My Orders
GE Washer Parts
GET YOUR OFFICIAL General Electric PARTS TO ENSURE VICTORY
Popular GE Washer Parts
Installation Instructions
Henry from OKANOGAN, WA
Noisy spin, no agitation.
Cleaned pulleys. Replaced worn belt.
This is a mode shifter or shift actuator for models of washing machine. Mode shifters are designed to change the function of the washing machine motor, between spinning cycles and agitation, and is usually installed at the bottom of the washer. If your washing machine is not spinning or agitating during its washing cycle, or if it simply does not start, this shift actuator is likely bad and in need of replacing. This shift actuator is made mostly of plastic, and features two holes to secure it with screws, as well as a single wire harness that connects within your washing machine. This shifter is an OEM part and is sold individually.
This is a mode shifter or shift actuator for models of washing machine. Mode shifters are designed to change the function of the washing machine motor, between spinning cycles and agitation, and is usually installed at the bottom of the washer. If your washing machine is not spinning or agitating during its washing cycle, or if it simply does not start, this shift actuator is likely bad and in need of replacing. This shift actuator is made mostly of plastic, and features two holes to secure it with screws, as well as a single wire harness that connects within your washing machine. This shifter is an OEM part and is sold individually.
What this part fixes:
- Cycle Not Advancing
- Noisy and Marks Left on Clothes
- Spinning Issues
Installation Instructions
Marvin from SHOSHONE, ID
Washer not spinning
Tilt washer back.
Remove belt gaurd.
Remove belt.
Remove pulley.
Remove clutch and shifter.
Install in reverse order
Remove belt gaurd.
Remove belt.
Remove pulley.
Remove clutch and shifter.
Install in reverse order
This is a clutch for your washing machine. The clutch is made of a white plastic material and is used within washing machines to engage and disengage the transmission during the wash and spin cycles, and ultimately help spin the basket of the tub so your clothes finish damp and not soaked. If your washer has issues with spinning or agitating, this part is likely broken or has worn out, and will need to be replaced. To replace this part, some disassembly of your washer will be required, and tools like a screwdriver and socket wrench will be needed. This clutch is sold as an individual and does not come with any other parts.
This is a clutch for your washing machine. The clutch is made of a white plastic material and is used within washing machines to engage and disengage the transmission during the wash and spin cycles, and ultimately help spin the basket of the tub so your clothes finish damp and not soaked. If your washer has issues with spinning or agitating, this part is likely broken or has worn out, and will need to be replaced. To replace this part, some disassembly of your washer will be required, and tools like a screwdriver and socket wrench will be needed. This clutch is sold as an individual and does not come with any other parts.
Installation Instructions
Marvin from SHOSHONE, ID
Washer not spinning
Tilt washer back.
Remove belt gaurd.
Remove belt.
Remove pulley.
Remove clutch and shifter.
Install in reverse order
Remove belt gaurd.
Remove belt.
Remove pulley.
Remove clutch and shifter.
Install in reverse order
This drain pump assembly is for washers. Drain pump assembly removes water from the washer during the drain portion of the cycle. The assembly may include multiple parts; refer to your parts diagram for a complete list of parts included.
This drain pump assembly is for washers. Drain pump assembly removes water from the washer during the drain portion of the cycle. The assembly may include multiple parts; refer to your parts diagram for a complete list of parts included.
Installation Instructions
Mike from NAPLES, FL
Washer ran fine but woudl not drain water - low humming noise
Drain all the water out of the tub with a shop vac
Remove rear drain hose and drained rest of water into a bucket
Remove small rear panel (bottom left hand corner) where the drain hose connects
Tipped washer up about 45 degrees to get underneath it - Supported it with a few paint cans
Remove internal drain hose/clamps ... Read more from pump - w/ pliers
Remove belt cover (gray plastic) with socket - 3 bolts
Remove wire assembly plug from socket
Remove old drain pump with socket - 3 bolts
Install new drain pump - 3 bolts - plug wire assembly into socket
Reinstall belt cover - 3 bolts
Reinstall hose to drain pump (note panel will be inside washer)
Feed drain hose panel through hole and reinstall - 1 nut
Re attached drain hose to exterior drain plug
You are done !
Remove rear drain hose and drained rest of water into a bucket
Remove small rear panel (bottom left hand corner) where the drain hose connects
Tipped washer up about 45 degrees to get underneath it - Supported it with a few paint cans
Remove internal drain hose/clamps ... Read more from pump - w/ pliers
Remove belt cover (gray plastic) with socket - 3 bolts
Remove wire assembly plug from socket
Remove old drain pump with socket - 3 bolts
Install new drain pump - 3 bolts - plug wire assembly into socket
Reinstall belt cover - 3 bolts
Reinstall hose to drain pump (note panel will be inside washer)
Feed drain hose panel through hole and reinstall - 1 nut
Re attached drain hose to exterior drain plug
You are done !
Read less
This is a manufacturer-made suspension rod and spring assembly for your washing machine. This suspension rod is one of four suspension rods that make up the entirety of the inner suspension of your washing machine, and if worn out or damaged, must be replaced immediately. If you hear loud or excessive banging noises from your washing machine, this and/or other suspension rods within the washing machine are worn out. This specific suspension rod is the left assembly, so the parts for the other side of your washing machine will also be required when replacing this one, considering they all wear at a relatively similar rate. This suspension rod assembly is sold individually, so it does not come with any other suspension rods.
This is a manufacturer-made suspension rod and spring assembly for your washing machine. This suspension rod is one of four suspension rods that make up the entirety of the inner suspension of your washing machine, and if worn out or damaged, must be replaced immediately. If you hear loud or excessive banging noises from your washing machine, this and/or other suspension rods within the washing machine are worn out. This specific suspension rod is the left assembly, so the parts for the other side of your washing machine will also be required when replacing this one, considering they all wear at a relatively similar rate. This suspension rod assembly is sold individually, so it does not come with any other suspension rods.
Installation Instructions
Lawrence from FREDERICKSBRG, TX
Faild to spin with leavy clothes
Unplugged washer and hoses. Removed 4 screws in back control panel and 4 screws holding control panel down. Drained capacitor and checked that. It was good. Pryed washer top off with screw driver. Used vice grips to remove old and install new spring rods, replacing them one at a time. While lid was off I cut a small diameter pool noodle i
... Read more
n half and cut 4 half noodles the size of each side. I unclipped one side of the tub cap and ran an 11" zip tie through the hole in the middle of one side and back up and out where the tub skirt and cap meet, then tied the half noodle to the edge of the tub cap and snapped down cap. Then repeated with the other three sides. I did this so heavier clothes, if they got out of balance, would continue to spin. The noodles keeping the tub from moving too far out of balance. The rod springs helped with lighter loads but still shut down spinning with heavy clothes. The machine always handled heavy clothes for 7 years until the last month or so. If it breaks with the noodles, I'll get another new machine.
Read less
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
This rod and spring assembly is designed to fit with washing machines and is made by the original manufacturer of your washer. It is a part of the washer suspension system that helps to stabilize and support the drum. The rod is a cylindrical plastic component that connects the drum to the outer frame of the washing machine. The spring is made of metal and provides tension and elasticity. The assembly is designed to absorb shocks and vibrations while the washer is running to help prevent excessive movement. If the assembly is damaged or out of alignment, the washer will be unstable and noisy. This assembly is designed to fit on the right side of the washer.
This rod and spring assembly is designed to fit with washing machines and is made by the original manufacturer of your washer. It is a part of the washer suspension system that helps to stabilize and support the drum. The rod is a cylindrical plastic component that connects the drum to the outer frame of the washing machine. The spring is made of metal and provides tension and elasticity. The assembly is designed to absorb shocks and vibrations while the washer is running to help prevent excessive movement. If the assembly is damaged or out of alignment, the washer will be unstable and noisy. This assembly is designed to fit on the right side of the washer.
Installation Instructions
Lawrence from FREDERICKSBRG, TX
Faild to spin with leavy clothes
Unplugged washer and hoses. Removed 4 screws in back control panel and 4 screws holding control panel down. Drained capacitor and checked that. It was good. Pryed washer top off with screw driver. Used vice grips to remove old and install new spring rods, replacing them one at a time. While lid was off I cut a small diameter pool noodle i
... Read more
n half and cut 4 half noodles the size of each side. I unclipped one side of the tub cap and ran an 11" zip tie through the hole in the middle of one side and back up and out where the tub skirt and cap meet, then tied the half noodle to the edge of the tub cap and snapped down cap. Then repeated with the other three sides. I did this so heavier clothes, if they got out of balance, would continue to spin. The noodles keeping the tub from moving too far out of balance. The rod springs helped with lighter loads but still shut down spinning with heavy clothes. The machine always handled heavy clothes for 7 years until the last month or so. If it breaks with the noodles, I'll get another new machine.
Read less
This lid lock, also known as a door lock, is a genuine OEM replacement part for your washing machine. The lid lock keeps your washer lid closed during the washing cycle. If this part is broken, your washer may not run because it thinks the door is open, or it will not keep the door locked during the wash cycle. To replace this part, make sure you disconnect power to the appliance and wear work gloves.
This lid lock, also known as a door lock, is a genuine OEM replacement part for your washing machine. The lid lock keeps your washer lid closed during the washing cycle. If this part is broken, your washer may not run because it thinks the door is open, or it will not keep the door locked during the wash cycle. To replace this part, make sure you disconnect power to the appliance and wear work gloves.
Installation Instructions
Wiley from Wilson, NC
Wife pull up door when it was in lock mode
Lift up door removed lid lock with screwdriver installed new part
The tub dampening straps support the wash tub and reduce vibration by keeping the tub at the center of the cabinet. If your washer shakes and moves, or is making a loud banging noise during the wash cycle, the washing machine tub could be off-balance, meaning one or more of these straps may be loose, or broken. Other symptoms include: the washer leaking, not agitating, or pumping but not spinning. These straps are sold individually. However, we recommend that you replace all 4 straps at the same time. It is also recommended that you check the tub for cracks where these straps mount.
The tub dampening straps support the wash tub and reduce vibration by keeping the tub at the center of the cabinet. If your washer shakes and moves, or is making a loud banging noise during the wash cycle, the washing machine tub could be off-balance, meaning one or more of these straps may be loose, or broken. Other symptoms include: the washer leaking, not agitating, or pumping but not spinning. These straps are sold individually. However, we recommend that you replace all 4 straps at the same time. It is also recommended that you check the tub for cracks where these straps mount.
Installation Instructions
molly from laguna niguel, CA
broken dampening strap and loose agitator
first remove the front washer cover by finding the two pressure clips that hold it to the top lid. gently push the putty knife into the clips one at a time. this will raise and separate them from the front panel. the panel will tilt forward and u can now remove it from the bottom clips by sliding it up and out. to open the top cover u rem
... Read more
ove the two 1/4 in screws on the sides of the front panel and lift the top. make sure to secure it in place or unplug the single electrical connection at the rear and remove the whole top from the clips, its really simple and the most convenient mehtod. to remove the straps u can now get to all four without much interference. there are two size screw heads so make sure u have a nut driver or small socket set. after changing the straps i went to change the agitator coupling. the agitator pulled directly up without a problem. just put your two hands under and pull straight up with one good jolt. the plastic coupler has one bolt in the middle that came out easily with a small socket set. my problem arose when the plastic coupler would not come off the metal shaft. after a short time of pulling and prying i finally decided to cut it off. using a small hacksaw and taking my time i put two cuts into the coupler. they were on opposite sides and where vertical, running along the steel shaft. i could now split it in two and it came off very easily and quickly. now when putting on the new one make sure the splines line up. push as far down as u can then use the center bolt to seat the gear all the way down. the agitator also has to be lined up just right. it also has splines on the interior that allow it to line up with the coupler and merely push down until it reseats itself in place. replace the top of the washer and then the front panel. don't forget to rebolt the top panel to the frame. push the front panel in until it snaps into place. full replacement time was about 40 minutes and actually not bad with the right tools.
Read less
This is an agitator assembly for washing machines. Agitators are used within top load washing machines to move back and forth and effectively wash your clothes. However, if the agitator currently in your washing machine is damaged and/or worn out, it needs to be replaced for your washing machine to operate properly. Replacing this agitator assembly will require a wrench, and for you to turn off the power and water supply for your washing machine. This agitator assembly is an OEM part that is sold individually and does not come with any other parts or accessories.
This is an agitator assembly for washing machines. Agitators are used within top load washing machines to move back and forth and effectively wash your clothes. However, if the agitator currently in your washing machine is damaged and/or worn out, it needs to be replaced for your washing machine to operate properly. Replacing this agitator assembly will require a wrench, and for you to turn off the power and water supply for your washing machine. This agitator assembly is an OEM part that is sold individually and does not come with any other parts or accessories.
Installation Instructions
MICHAEL from LK PEEKSKILL, NY
Agitator wore out over time and needed to be replaced
Replacing was easier than opening the box it came in. Used a 7/16 socket and a few extensions to reach the bottom of the agitator. It came out super quick cleaned out the fabric softener older than my kids from under it. Lined up the groves of the new one and it slid easily. I took a small piece of painters tape and crumbled it into a sm
... Read more
all ball and put it in the socket to keep the bolt in place while it lowered it into the agitator. Made it snug and we were back in business good as new!!!
Read less
This auger is an authentic OEM replacement part specially designed for washing machines. It is a white, spiral-shaped agitator located in the center of the wash basket. During the wash cycle the auger rotates to move the clothes, lifting them up and then dropping them back down into the water and detergent solution. By agitating the clothes, the auger helps to loosen dirt, stains, and debris, to ensure that your clothes receive a thorough and effective cleaning. Signs of a faulty auger include unusual noises like grinding and scraping, incomplete wash cycles, and torn or tangled clothing.
This auger is an authentic OEM replacement part specially designed for washing machines. It is a white, spiral-shaped agitator located in the center of the wash basket. During the wash cycle the auger rotates to move the clothes, lifting them up and then dropping them back down into the water and detergent solution. By agitating the clothes, the auger helps to loosen dirt, stains, and debris, to ensure that your clothes receive a thorough and effective cleaning. Signs of a faulty auger include unusual noises like grinding and scraping, incomplete wash cycles, and torn or tangled clothing.
Installation Instructions
Cody from BALDWIN CITY, KS
Broken auger; could turn both ways.
Upper portion of auger spins on bottom portion so they need to be locked together with a screwdriver to twist off counter clockwise. Good instructions here: https://m.youtube.com/watch?v=Qr4GzTJBho0&vl=en. Someone needs to hold the tub while another uses the strap wrench to turn the auger counter clockwise. Should pop off with a bit of f
... Read more
orce. New one pops on easy.
Read less
Genuine OEM GE Washer Parts
GE dryers are known for their high power and cleaning efficiency. If you own a GE washer, you are likely familiar with features such as the UltraFresh Vent System, Odor Block, and SmartDispense. To keep enjoying these features, you will likely need to perform regular maintenance on your washer. We are here to help!
PartSelect has been a leading online retailer for over 25 years, and we are proud to carry genuine OEM parts for various GE models such as the GE Adora, GE Allura, and GE Profile. Each OEM part is designed to the same high quality as the original. And for your peace of mind, we offer a?365-day?return period and a 1-year warranty on all our electronic parts. Browse our wide selection of GE control boards, drain pumps, door switches, filters, and more.
- Fit
- Quality
- Warranty
Common GE Washing Machine Problems and How to Fix Them
Troubleshooting your GE washing machine may look tough, but don’t worry. We provide expert repair guides to help you find and address any issues you may have. You can trust our ability to make troubleshooting your washing machine easy and successful.
Noisy GE Washing Machine – Your GE washing machine has a variety of parts that experience motion during use. It is not uncommon for these parts like pumps and drive belts to become worn over time and start to create unpleasant noises like knocking or grinding. Determining the cause of the noise in your washing machine is as easy as isolating the area where the noise is coming from.
Leaking GE Washing Machine – It may be alarming to see water leaks coming from your GE washing machine. With the motion created by use, it is not uncommon to see a part like a pump or hose develop a bad seal or become damaged leading to a water leak. You can address the problem by finding the source of water to ensure all connections are in place and no damage is present, making sure your machine can run without any water leaks.
GE Washing Machine Will Not Start – Dealing with a GE washing machine that won’t start can be annoying. This is frequently related to damaged drive motors or start switches, but it could also be due to a broken door or lid strike. After making sure the problem is not simply caused by a loose power cord, which can happen as the machine moves during use, you should first inspect the lid or door strike for any damages which would not allow this to latch, then move on to the electrical parts such as drive motor or start switch. By addressing these areas you can fix the problems, allowing your appliance to start once again.
GE Washing Machine Will Not Spin – It can be unsettling when your GE washing machine’s spinning function is not working as expected. With the number of moving parts in your machine, it’s not surprising to face issues like a damaged door lock or a worn-out direct drive motor coupling. By inspecting these areas, you can pinpoint and repair the issue, ensuring your washing machine spins properly.
GE Washing Machine Does Not Drain – If your GE washing machine is failing to drain, it could be as simple as checking the parts essential for proper drainage. This issue is often caused by obstructions within a connection hose or a blockage within the pump itself. By looking at these key areas, you can identify and resolve the problem, allowing your washing machine to drain after each cycle.
Related General Electric Washer Articles
Troubleshooting and repair help from people who do this every day.
How to Clean Your Top Load Washer
How to properly clean your top load washer to eliminate odor and keep it fr...
How to Remove Common Items From Your Front Load Washer
Find your mysteriously missing coins, socks and bank cards by taking a quic...
How to Clean a Front Load Washer
Spring is here, and we are cleaning up all our appliances! A washer is supp...