Garbage Disposer Parts

Popular Garbage Disposer Parts

Your Price
$21.24
   In Stock
Garbage Disposer Garbage Disposal Drain Stopper
★★★★★
★★★★★
8 Reviews
PartSelect Number PS12726321
Manufacturer Part Number WC11X20163
The splash guard, also known as a mounting gasket, is used for garbage disposals. The guard creates a tight seal between the sink and the garbage disposal ring. This part is black in color and made of rubber. It covers the top of the sink drain and it opens in the center to allow water and food particles into garbage disposal. It does this while ensuring liquids and food do not splash back into the sink. This should be a solution to your issue of garbage coming back out of the sink. Refer to the instructional diagram provided by the manufacturer for installation instructions.
Fixes these symptoms
Installation Instructions
Alan from HOPEWELL, VA
No stoppet
Put it in the hole. Read more...
Your Price
$39.58
   In Stock
Garbage Disposer Sink Flange
★★★★★
★★★★★
1 Review
PartSelect Number PS12722852
Manufacturer Part Number WC15X20161
The sink flange attaches to your sink drain opening and provides a connection to mount the disposal unit to the sink itself. If your food waste disposer is leaking, there are a few places that you should inspect. If the leak appears to be coming from around the connection to the sink, look carefully at the sink flange, as there could be an issue with the flange itself, or its gaskets. Remember to disconnect the power from your food waste disposal unit before beginning this repair. This OEM replacement part has an outer diameter of approximately 4.5 inches, and an inner diameter of approximately 3 inches.
Fixes these symptoms
Your Price
$17.43
   In Stock
Garbage Disposer Flange Gasket - Fiber
PartSelect Number PS6883604
Manufacturer Part Number WC03X10008
This item is sold individually. The fiber sink flange gasket works with your food waste disposer. This part creates a seal that prevents any water from leaking. It is positioned between the sink flange and the disposal mounting ring. The flange may break apart over time and cause leaking and will need to be replaced. The flange gasket is donut shaped and is 4 inches in diameter. Before beginning this repair make sure the power to the food waste disposer has been disconnected. This is an OEM part that is obtained right from the manufacturer.
Fixes these symptoms
Installation Instructions
Donald from Tampa, FL
Leaky GE Disposall
Mount Ring was very difficult to remove. Hammer needed to unlock. Once removed, rubber and fiber gaskets were easily replaced. Cushion Mount did not attach properly to sink flange after many attempts, so Mount Ring was placed too high for hopper to attach. The cushion mount was finally placed on flange correctly (not sure why it attached incorrectly previously) but all is well with no leaks. Dishwasher hose needed to be re-attached after hopper mounted and locked in position. Read more...
Your Price
$32.72
   In Stock
Garbage Disposer Splash Guard
★★★★★
★★★★★
7 Reviews
PartSelect Number PS11742344
Manufacturer Part Number WP4211334
The splash guard, also known as a mounting gasket, is used for garbage disposals. The splash guard creates a watertight seal between the sink flange and the garbage disposal ring. The rubber cover covers the top of the sink drain and it opens in the center to allow water and food particles into the garbage disposal while keeping liquids and food from splashing out or back into the sink. This should fix any issue or symptom of garbage coming back out of your sink. Refer to the manufacturer-approved instructional diagram for installation and accurate guidance.
Fixes these symptoms
Installation Instructions
Richard from CENTERVILLE, UT
Worn out splash guard
Ask my grandson to replace it. He’s a genius. He used hammer to release the disposer circular latch. He then removed the old splash guard and installed the new one. Love him Read more...
Your Price
$17.70
   In Stock
Garbage Disposer DISPOSER DRAIN ELBOW KIT
★★★★★
★★★★★
1 Review
PartSelect Number PS12722851
Manufacturer Part Number WC14X20160
This is an elbow outlet and gasket for a food waste disposer or garbage disposer. This part connects the disposer to the drain pipe in your home. If you notice a blockage or a leak, you may need to replace this part. It is black in color, made of plastic, and measures about 6 inches tall.
Your Price
$12.72
   In Stock
Garbage Disposer Disposer Splash Guard
★★★★★
★★★★★
1 Review
PartSelect Number PS257945
Manufacturer Part Number WC3X124
This splash guard attaches to the garbage disposal in your sink, and prevents water and food debris from splashing back up when the disposal is operating. If your current splash guard is damaged, you should consider replacing it. This part is black in color, and is made of rubber. It is approximately 3 inches in diameter. This splash guard has a small opening in the middle that is approximately 1/4-inch in diameter, as well as 12 smaller openings and slits that allow you to feed water and food items into the garbage disposal. This product is sold individually, and works in conjunction with the stopper, part 3506779.
Installation Instructions
Aubrey from Hugo, OK
Splash guard worn out
pulled out the old and stuck in the new--so easy a caveman could do it. Read more...
Your Price
$11.10
   In Stock
Garbage Disposer Hose Clamp
★★★★★
★★★★★
2 Reviews
PartSelect Number PS11740613
Manufacturer Part Number WP285655
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installation, you will need a flat head screw driver to replace the clamp and a drill to access the screws to remove the front of the washer. Be careful if you do not have specific clamp pliers as the clamp could fly off. Once the front of the washer has been removed, take a quick look for water damage or any obvious signs of where the leak is coming from. If it is not obvious, run water to test.
Fixes these symptoms
Installation Instructions
Stephen from Laveen, AZ
Drive Pump Leaked
It took some trial and error but overall not a difficult project. 1. Take the front covers off. 2. Undo the pully spring to loosen belt 3. Remove belt off idler pulley wheel and free up belt from the large wheel. 4. Disconect the wiring harness and the hoses. 5. Undo the motor mounting bolts (4) 6. Take motor out of washer and remove the 3 screws holding the pump to the motor. 7. The pump had melted to the shaft and required I chisel the pump off of the shaft. 8. Attach new pump paying attention to where the belt is positioned. 9. Reattach the motor bolts, hoses, and wiring harnes. 10. Attach the belt and test the pump. 11. Put the front back on. Read more...
Your Price
$7.76
   In Stock
Garbage Disposer Hose Clamp
★★★★★
★★★★★
1 Review
PartSelect Number PS11743008
Manufacturer Part Number WP596669
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This clamp is used to securely attach a hose to another part of your appliance, which helps prevent leaks from those connections. Depending on the appliance, it can attach hoses to drain pumps, water inlet valves, pressure switches, and injector nozzles. We recommend you refer to model-specific diagrams for appropriate uses and exact placement. This hose clamp is made of metal, and is sold individually. To access and replace this part you will need a nut driver, pliers, and screwdrivers. Before you begin any repair work, make sure you have unplugged your appliance, and shut off the water supply if applicable.
Fixes these symptoms
Installation Instructions
jeff from lindenhurst, IL
Washing Machine was leaking water
Loosened the hose clamp, removed the injector valve and injector nozzle assembly, replaced both and tightened with new hose clamp. Fixed the problem for less than $20!! Washing machine is 20 years old and this was the first problem--hopefully it is now good for another 20 years! Read more...
Your Price
$11.30
   In Stock
Garbage Disposer SUPPORT RING
★★★★★
★★★★★
1 Review
PartSelect Number PS7783352
Manufacturer Part Number WC05X10002
This support ring, also known as mounting ring, is a genuine OEM replacement part for use in food waste disposers. It is a circular plastic piece with an outer diameter of 4.75 inches. It is found inside the disposer housing where it provides support and stability to the unit. The ring helps to evenly distribute the weight of the disposer and waste evenly, so that the disposer does not fall out of alignment. Over time, the support ring may break due to the continuous grinding within the unit, and the exposure to moisture and waste. If the ring is no longer able to stabilize the unit, you will notice food and waste leakage, excessive vibrations, and damage to the disposer components. To begin this repair, first disconnect the disposer from the mounting assembly, and pull out the faulty ring. Place the new ring in its place and reattach the disposer to the mounting assembly.
Your Price
$7.95
   In Stock
Garbage Disposer Sink Flange Gasket/Seal
PartSelect Number PS11742343
Manufacturer Part Number WP4211302
This is a sink flange gasket that is designed for use within various models of sinks and is installed between the strainer and garbage disposal. Made of rubber and measuring approximately 4.5-inches in outer-diameter, this seal can become damaged or worn over time and through extended use can lead to leaks from the disposal, at which time it will need replacing. This seal is sold individually, and because there are two seals in the gasket, you may need to consider acquiring multiple. When replacing this flange gasket, you will likely need a screwdriver and wrench to gain access to the pipes holding this seal. It is important that you disconnect the power and water supply before doing any repairs.
Fixes these symptoms

Garbage Disposer Brands

Popular Garbage Disposer Models

Below are the most popular Garbage Disposer models we have. Enter your model number in the search box to find your model.