Murray Parts

Murray Appliance Parts

Popular Murray Parts

Your Price
$5.97
   In Stock
Murray Bearing
★★★★★
★★★★★
3 Reviews
PartSelect Number PS9006914
Manufacturer Part Number 532009040
The OEM bearing, also known as the flange bearing, is silver, made of metal, and sold individually. It is used on riding mowers to secure the wheel in place and allow it to rotate freely on the shaft. Over time, the part may become worn and damaged, which you will notice if you experience a squealing or grinding sound from the wheel in question, or you notice the wheel is sloppy on the shaft. You will need a hammer and punch to complete this repair, which most of our customers rated as easy. Make sure you tap the new bearing into place evenly inside the tire rim.
Installation Instructions
robert from EUREKA, CA
transaxle rotated forward on 2015 Husqvarna YT42DXLS
2015 Husqvarna YT42DXLS. Both transaxle support struts broke causing the transaxle rotated forward and shear transaxle mounting bracket. The transaxle was not damaged. All 3 parts required replacement. There are some good youtube videos to watch to show how to complete the repair.

HINT: I removed the mower deck and placed jack stands under the frame to support the rear end of the mower. I then supported the transaxle with a floor jack. This worked great for positioning/aligning the transaxle up to the frame after the new mounting bracket was installed.

HINT: Due to the shearing of the transaxle mounting bracket, it was difficult to get a socket to seat correctly on the some of the nuts securing the transaxle to the mounting bracket. I highly recommend getting 4 new nuts because you will likely damage/strip the nut while removing it.

HINT: The youtube videos all show removing the rear tires. The rear tires can be difficult to remove; and there are some interesting youtube videos on removing stuck rear tires. If you have a stuck rear tire, you can complete the repair with the tires on; it is just a bit more challenging to squeeze your hands behind the tire to reach the bolts. I was able to only get one tire off.

HINT: If I wasn't able to do the repair with the rear tire on, my idea for getting the rear tire off was to fabricate a bracket that would work with a gear puller. The plan was to utilize the two symmetrical 1/4 inch-ish size holes in the rim to install 12" long bolts. I would then install a C-channel over the bolts, which would place the C-channel directly over the axle. I would then drill a hold in the C-channel for the gear puller bolt to go through. The shoulders of the gear puller bracket would then push against the c-channel. I was planning on using a few large fender washers on the back side of the rim to help prevent the rim from getting damaged when pulling the tire. You will be pulling the rim about 3 inches to get it off the axle.

HINT: It look four hours to repair plus another half hour of watching youtube videos; probably would have taken two hours if I didn't spend two hours trying to take off one of the rear tires that was stuck.

HINT: Since I was working under the mower, I also replaced the drive (motion) belt as preventative maintenance.
Read more...
Your Price
$3.58
   In Stock
Murray Ring Klip Number T5304-75
★★★★★
★★★★★
1 Review
PartSelect Number PS9143890
Manufacturer Part Number 812000029
The Ring Klip Number T5304-75, also known simply as a ring clip, is an OEM part designed to secure your mower wheel to its axle. This part is black, made of metal, and around an inch in length. It is sold individually and may become damaged over time due to wear and fatigue.
Installation Instructions
Anthony from OLIVEHILL, TN
Wheel bushings were bad
Removed old clip removed rim from tractor, removed grease fitting on rim, took hammer and screw driver knocked out old bushing turned rim over knocked out other bushing. Press in new bushings reinstalled grease fitting slide tire back on tractor, put retaining washers on then locking clip put on dust cover grease at grease fitting. Repeat other side. Read more...
Your Price
$4.42
   In Stock
Murray Plug-Spark
★★★★★
★★★★★
1 Review
PartSelect Number PS9140427
Manufacturer Part Number 796112S
This part is the replacement spark plug for your engine. It measures approximately 2.5 inches by 1 inch. The spark plug creates the spark that ignites fuel in your engine during the combustion process. Over time, spark plugs can become worn and can go bad, which will prevent the engine from firing. You can test your spark plug for continuity with a multimeter, and inspect it for corrosion if you suspect the spark plug has gone bad. This is an OEM part sourced directly from the manufacturer and it is sold individually.
Fixes these symptoms
Installation Instructions
David from KNOXVILLE, TN
Replace carburetor
Loosened engine cover and moved out of the way
Removed air intake and filter
Loosened and disconnected gas line to carburetor
Unscrewed carburetor and disconnected from throttle arm
Reversed process using new carburetor, O-ring and gasket
Read more...
Your Price
$3.58
   In Stock
Murray Cap Axle Black 1 50 x 1 00
★★★★★
★★★★★
1 Review
PartSelect Number PS9007667
Manufacturer Part Number 532104757
This genuine black cap axle, also sometimes known as the dust cap, is around 2 inches in diamater and sold individually. Comprised of plastic, it is designed to keep debris out of the hub and axle of your lawn mower or garden tractor. Over time, your dust cap may become damaged or lost due to wear and tear. If this happens, dirt and debris can freely enter the axle and hub, causing damage. This is an easy repair to make and does not require any tools. Just look for the cap axle on the rim of the wheel to make your repair.
Installation Instructions
Anthony from OLIVEHILL, TN
Wheel bushings were bad
Removed old clip removed rim from tractor, removed grease fitting on rim, took hammer and screw driver knocked out old bushing turned rim over knocked out other bushing. Press in new bushings reinstalled grease fitting slide tire back on tractor, put retaining washers on then locking clip put on dust cover grease at grease fitting. Repeat other side. Read more...
Your Price
$3.58
   In Stock
Murray Washer 25/32 x 1-1/4 x 16 Ga.
★★★★★
★★★★★
2 Reviews
PartSelect Number PS9008998
Manufacturer Part Number 532121749
This OEM washer, also known as a flat washer, has dimensions of 25/32 x 1-1/4. Silver in color and metal, the washer is sold individually. Although this part can have a range of applications depending on the equipment, its general function is to spread the load under a bolt. Ensure you consult your owners manual or check your model number to confirm this is the washer you need for your equipment. This part will need to be replaced when your existing one is worn or damaged. It is an easy repair according to our customers, and does not require any special tools.
Installation Instructions
Frederick from BINGHAMTON, NY
Front wheels, too much end play
Shimmed the wheels out on axle.. No more slop. Read more...
Your Price
$12.77
   In Stock
Murray Cutting Head Assembly
★★★★★
★★★★★
1 Review
PartSelect Number PS10009816
Manufacturer Part Number 753-08169
Your Price
$17.26
   In Stock
Murray Carburetor Overhaul Kit
★★★★★
★★★★★
4 Reviews
PartSelect Number PS8984098
Manufacturer Part Number 498260
This is a replacement carburetor overhaul kit for your small engine. The carburetor is essential to the overall performance of your engine, and the carb can get clogged up over time for a variety of reasons. When your carb becomes clogged, it is often a good idea to take it apart and replace the various parts inside by purchasing a carburetor kit. This is a 15-piece set and contains everything that you will need to do a total overhaul of your carburetor. You may want to purchase some carb cleaner as well, to ensure that the new pieces in the carb kit fit and adhere properly.
Fixes these symptoms
Installation Instructions
Jonathan from LIBERTY TWP, OH
Smelled Gas Leaks
Inspected/removed fuel lines and found signs of leak. Removed and inspected carburetor and found that seals and gaskets were toast. Replaced said seals with ones from the kit that fit and replaced fuel lines.

Would be nice to have a fuel line kit with the big fuel line (tank to carb) and the little one (carb to engine) together with all the necessary clamps.
Read more...
Your Price
$46.68
   On Order
Murray Lawn Tractor Mandrel Assembly
★★★★★
★★★★★
2 Reviews
PartSelect Number PS12087499
Manufacturer Part Number 587819701
Your Price
$4.78
   In Stock
Murray Washer Hardened
PartSelect Number PS9015920
Manufacturer Part Number 532188967
This OEM hardened washer spreads load under the bolts of your lawn tractor. It is silver, made of metal, and is sold individually. Over time, the washer may become damaged due to wear and fatigue, and will need to be replaced. You may notice this part is damaged if you start hearing a grinding or rubbing noise between the tire rim and ring clip. You will need a pair of needle nose pliers to carry out this repair, which our customers generally found easy. You will locate the washer on the spindle, between the wheel and the ring clip.
Your Price
$7.58
   In Stock
Murray Seal--Oil (PTO Side)
★★★★★
★★★★★
2 Reviews
PartSelect Number PS9151828
Manufacturer Part Number 795387
This OEM Seal-Oil (PTO Side), also called the Oil Seal, is a Black, Nitrile Rubber, 2/14 O.D., individually sold part which is installed using a Seal Puller. Customers rate the installation difficulty as Medium. This part provides a seal around the crank shaft and engine block. When installing onto the engine block around the crank shaft, use something that makes contact around the entire seal, like a large socket or pipe, and tap into place evenly, ensuring that the housing is clean and dry. If the part is broken, likely due to fatigue, there will be leaking oil, and this part should be replaced using the model number on the original part to confirm it is the right fit for your model.
Installation Instructions
rodney from MUSCATINE, IA
governor not working
Had to pull the engine off the rider mower. Drained the oil took shield off the flywheel. Set it upside down on a 5 gal bucket. Took a 7/16 hand wrench to remove governor lever from bottom of engine. Left it in its location. Pulled 10 1/2 " bolts. Split engine case. Found the old governor had broke into pieces. Had to use a magnet to remove all the pieces. Removed the small clip and removed gear. Lubed shaft slid new on put new clip on. Lined governor weights with center piece tapped it in place very lightly. Cleaned gasket flanges pulled the shaft seal. Used the old seal as a seal driver. When putting the cover back on make sure the seal dont roll out. Take a mini screwdriver and tuck it in around shaft. Put bolts back in and tighten like instructions Read more...

Related Murray Parts

Popular Murray Models

Below are the most popular Murray models we have. Enter your model number in the search box to find your model.