Official Electric Drill Parts

Your Price

$20.09

PartSelect Number PS12508695

Manufacturer Part Number N413423

This OEM housing assembly in your impact driver is the protective outer casing that encloses the internal components of the tool, providing structural support. The assembly consists of both the top and bottom sides and it operates using a 20-volt battery. To identify if the housing assembly is broken, look for visible cracks, fractures, or loose components. Excessive vibration or unusual noises during operation can also indicate a problem. To replace the housing assembly, remove all the screws and separate the case. Transfer all the components from the old case to the new one, ensuring switches like the forwards and reverse switch and power settings are properly aligned. Then, reassemble the case by putting all the screws back in using a screwdriver with a Torx bit. Note that the screws are sold separately from the housing.

Carbon Brush Assembly – Part Number: 22-18-0680

Your Price

$5.37

Electric Drill Carbon Brush Assembly

PartSelect Number PS10122192

Manufacturer Part Number 22-18-0680

Genuine Milwaukee replacement part. Includes 1 Carbon Brush with wire lead, brush spring and bracket attached. • Worn brushes frequently are the cause behind a motor running poorly. • Replacing brushes can fix a motor that's operating intermittently. • New brushes can restore a motor's electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

Your Price

$11.22

Electric Drill Carbon Brush Set

PartSelect Number PS10156649

Manufacturer Part Number CB303

This set of two carbon brushes is a genuine Makita replacement part, packaged in an official Makita retail box. Each brush includes wire leads and attached brush springs, and is designed to restore optimal performance in compatible Makita tools. Carbon brushes are among the most commonly replaced components in power tools, as they gradually wear down through friction and regular use. Worn brushes can lead to intermittent motor function, reduced power, or diminished electric braking. Replacing them can resolve these issues and restore proper motor performance. Signs of wear include brushes worn near the wire lead, or those that are cracked, pitted, or burned. When replacing carbon brushes, it’s also important to inspect the armature for any signs of damage, such as burns or cracks, which may indicate a more serious motor issue.

Videos!

Your Price

$22.86

Electric Drill Power Cord

PartSelect Number PS10169875

Manufacturer Part Number 330072-98

Length: 8' Gauge: 18 Wires: 2 Type: Bare Wire This cord is a genuine DeWalt replacement part. This cord is compatible with the list of models below. This part is made for double insulated tools It is a two wire cord with two prongs and does not need a ground wire. The cord is sold individually. Installation of this part requires the new cord wires to go correctly into wire terminals also routing the cord and wires in the right path can help avoid pinching when the tool case (Plate) is put back into place.

Your Price

$10.42

Electric Drill Carbon Brush

PartSelect Number PS10122195

Manufacturer Part Number 22-18-0701

Genuine Milwaukee replacement part. This brush is sold individually, 2 are needed for the tools shown below. It is always best to replace both brushes, even if only one is worn.Worn brushes frequently are the cause behind a motor running poorly.Replacing brushes can fix a motor that's operating intermittently. New brushes can restore a motor's electric braking.Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

Your Price

$6.18

Electric Drill Carbon Brush

PartSelect Number PS10167153

Manufacturer Part Number 176846-04

This carbon brush is an authentic DeWalt replacement part. It is sold individually, 2 are needed to make a set • Worn brushes are frequently the cause of a poorly running motor. • Replacing brushes can fix an intermittently operating motor. • New brushes can restore a motor's electric braking. Carbon motor brushes are one of the most commonly replaced power tool parts. The reason is that carbon brushes are wear items, meaning that through friction and use they will gradually wear away and eventually will need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, also check your armature for burns, cracks, or other damage which are indications of a larger motor problem needing attention.

Your Price

$20.92

Electric Drill Power Cord

PartSelect Number PS10153834

Manufacturer Part Number 664064-4

Length 8 Foot Length: 6' Gauge: 18 Wires: 2 Type: Bare Wire This power supply cord is a genuine OEM sourced replacement part. It is specially made to supply power from a standard outlet to Makita power tools. A cracked or damaged cord should be replaced before continuing to use the tool. This rubber insulated cord is sold individually. It comes with a rubber sleeve grommet that is not sold separately. Replacing this power supply cord you will need a screwdriver. • Remove the housing screws • Remove the the housing • Disconnect the old cord wires • Remove the old power cord • Secure the new cord in place • Connect the wires • Reassemble and test the new cord

Installation Instructions

Bruce from HILLSBORO, OR

Old power cord frayed at the grommet entering the drill casing

Did not do repair as replacement part did not match description on partselect website. The grommet is not part of the replacement that was sent. Order #22962198
Email sent (11/16/2023) to partselect.com has gone unanswered
Thanks? Read more...

Your Price

$18.61

Electric Drill Carbon Brush

PartSelect Number PS10122196

Manufacturer Part Number 22-18-0702

Original Milwaukee replacement part. This Brush is sold individually, most repair jobs will require Two (2) of this item. As pictured, this brush is ready to install and includes carbon brush, wire lead, and spring. Over time, brushes will wear down and eventually require replacement. Carbon motor brushes are one of the most commonly replaced power tool components. Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power. A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned. When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.

Videos!

Your Price

$6.15

Electric Drill Carbon Brush

PartSelect Number PS10122113

Manufacturer Part Number 22-16-0275

Genuine Milwaukee replacement part Includes 1 Carbon Brush sold individually. Please go to the schematic listings for your tool to find the brush assembly parts compatible with this carbon brush and your tool. This carbon brush will fit a wide variety of Milwaukee tools. • Worn brushes are frequently the cause of a poorly running motor. • Replacing brushes can fix an intermittently operating motor. • New brushes can restore a motor's electric braking. Carbon motor brushes are one of the most commonly replaced power tool parts. The reason is that carbon brushes are wear items, meaning that through friction and use they will gradually wear away and eventually will need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, also check your armature for burns, cracks, or other damage which are indications of a larger motor problem needing attention.

Your Price

$11.22

Electric Drill Carbon Brush Set

PartSelect Number PS10156657

Manufacturer Part Number CB408

This #191938-1 (CB-408) Makita carbon brush set contains two individual carbon brushes with wire leads and brush springs attached. The set contains genuine Makita replacement parts, and comes packaged in a Makita retail box. This brush set will fit the Makita tools listed at the bottom of the page. • Worn brushes are often the cause of a poorly running motor • Replacing brushes can fix an intermittent motor • New brushes can restore a motor's electric braking Carbon motor brushes are one of the most commonly replaced power tool components. Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power. A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned. When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.

Shop by Department

Top Appliance Brands

Top Lawn Equipment Brands

Electric Drill Parts

Popular Electric Drill Parts

Related Electric Drill Parts

Popular Electric Drill Models

Shop by Department

Top Appliance Brands

Top Lawn Equipment Brands

Sample Model Number Tags

EasyApplianceParts is Now PartSelect!

Electric Drill Parts

Find Your Part

Popular Electric Drill Parts

Related Electric Drill Parts

Popular Electric Drill Models