Official Drill Parts – PartSelect.com

Your Price

$13.44

PartSelect Number PS10156653

Manufacturer Part Number CB340

Set of 2 Carbon Brushes with wire leads and brush springs attached. The set contains genuine Makita replacement parts, and comes packaged in a Makita retail box. rnThis brush set will fit the Makita tools listed at the bottom of the page. • Worn brushes frequently are the cause behind a motor running poorly. • Replacing brushes can fix a motor that’s operating intermittently. • New brushes can restore a motor’s electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

Grinder Grinder/Sander Rotor Blade – Part Number: 1906PT

Your Price

$13.04

Drill Grinder Grinder/sander Rotor Blade

PartSelect Number PS12145308

Manufacturer Part Number 1906PT

Your Price

$15.21

Drill Rotor Blade Set

PartSelect Number PS10300599

Manufacturer Part Number CA144889

This is a set authentic replacement rotor blades commonly used on Chicago Pneumatic power tools. Supplied from original equipment manufacturer. These blades are attached to the rotor and they will push the air inside the power tool. This set includes four (4) compound material blades per order. Replacing these blades is an easy job and will require a set of wrenches and pliers.

Your Price

$5.95

Drill Shifter Button

PartSelect Number PS12525746

Manufacturer Part Number N397466

Your Price

$40.73

Drill Blades

PartSelect Number PS10336584

Manufacturer Part Number 01480

These authentic OEM sourced replacement rotor blades are commonly used on Dynabrade sanders and grinders. They are attached to the rotor inside the tool pushing the air. This set includes (4) compound material blades per order. Replacing these blades you will need a set of wrenches and pliers.

Blades/rotor (4 Pack) – Part Number: 01011

Your Price

$42.71

Drill Blades/rotor (4 Pack)

PartSelect Number PS10336518

Manufacturer Part Number 01011

These blades in your die grinders are located on the rotor within the motor housing. This OEM set includes four blades, each measuring approximately 1-1/2 inches by 3/8 inches. When the tool is turned on, the motor drives the rotor, causing the blades to spin rapidly and help you shape various materials. It is important to regularly check the condition of the blades and replace them if they are visibly worn out or misaligned. Additionally, pay attention to any unusual signs during operation, such as increased noise, vibration, or burning smells. To replace the blades, refer to your user manual for detailed instructions on how to disassemble the motor housing. Typically, you will need to secure the tool in a padded vise, then use an adjustable pin wrench to remove the lock ring. Proceed with disassembling the tool by removing the collet and rotor nut from the rotor shaft, followed by the cylinder, spacer, and the four blades from the rotor.

Your Price

$30.74

Drill Housing Assembly

PartSelect Number PS17016996

Manufacturer Part Number N578871

Housing Assembly

Your Price

$7.22

Drill Seal

PartSelect Number PS10336573

Manufacturer Part Number 01464

This is a manufacturer sourced replacement seal. It is specially produced for use with Dynabrade sanders. This is one of the seals for the tip valve/inlet bushing. Over time seals tend to shrink and crack allowing for air leaks. At that time it should be replaced to maintain top performance. It is made out of rubber material and it is sold individually. Replacing this item you would need a wrench to replace this item.