Oven Parts

This is a grease filter compatible with various microwaves. Grease filters are used to collect food grease and prevent buildups on the internal components of the microwave, such as the fans and other electronics. This grease filter is made of mesh and measures 7.5 inches long by 5 inches wide. If your current microwave grease filter is clogged with grease and not able to be easily cleaned, it should be replaced. This filter can be replaced easily by pulling on its D-clasp and pushing the new filter into place. Depending on how many filters your microwave uses, you may want to consider how many you need before ordering. This filter is an OEM part and is sold individually.

This is a flat style oven igniter used to light the oven burner in a gas range. When the element in this igniter glows white hot, the gas is released from the safety valves, which lights the oven burner. If your range is not heating properly, or not heating at all, it might indicate a problem with this part. If the element in the igniter is only glowing red or orange, or not glowing at all, it will need to be replaced. This is a shorter style igniter. It is 3.72 inches in length, and it features an 18-inch wire lead. This kit includes the igniter, an instruction sheet, a mounting bracket, and the two ceramic wire nuts needed for installation. This part has an amperage range of 3.2 to 3.6. Unplug your appliance before you start any repair work.

This is a 240 volt bake element for your oven or range. The kit comes with two installation screws and the element. The element functions by supplying heat from the bottom of the oven to bake or cook your food. You may need to replace the bake element if your oven is not heating properly. This is a black metal part (Width 13 inches, length 16.5 inches, depth 1-1/2 inches ) which can be installed onto your range with a screwdriver. Installation is rated as "medium" difficulty. This element is the part that heats to allow cooking, and if broken or missing you'll be unable to cook. This part attaches to the lower section of the range. Refer to your model number and user manual to ensure this part is right for you. Each screw gets screwed into each wire terminal with a Phillips screw driver. Hold the wires forward to make sure the wires do not fall back through the rear of the oven. Unplug your appliance or shut off your circuit breaker to the appliance before installing the new part.

The bake element in your oven is the part that provides heat when cooking. If your oven is too hot, or not hot enough, or does not heat evenly, you may need to replace the bake element. This part is 2600 Watts and 240 Volts. It is a closed hinged style bake element which is 15-3/4 inches long and 16-5/8 inches wide. The terminal depth is three inches and they are 1-3/4 inches apart. This part is made of metal and is black in color. Be sure to disconnect power to the oven before completing this repair.

This is a single OEM water filter used in refrigerators to remove impurities and particles from water that goes through the water and ice dispenser. It is used for reducing cysts, turbidity, lead, mercury, herbicides, and more. If your icemaker is not making ice, not dispensing ice, dispenses too little ice, or there is leakage and the fridge is making loud noises, replacing the water filter may be the solution. This filter is located in the front, top right of side-by-side refrigerators. You will know it is time for a new filter when the light on the freezer door dispenser lights up red, or after 6 months (200 gallons) of use. No tools are required for this easy repair. First, press the release button to pull out the old water filter and push and lock in the new water filter. Run water through the dispenser for about 3 minutes to prime the filter for use. Dispose of the water or use it to water plants. Press the indicator for 3-10 seconds to reset after this repair is complete. This carbon-based filter measures 6 x 3 x 7 Inches and is white plastic.

The temperature sensor, also known as the oven temperature sensor assembly is usually found in the back of the oven. The function of the oven temperature sensor assembly is to measure the temperature inside your oven while it is on and send the temperature back up to the electronic control, which adjusts as necessary. If your oven is having difficulty achieving warmer temperatures and/or keeping warmer temperatures up, you may want to test your temperature sensor. Before you make this repair remember to unplug your range from the power source, and turn off the gas shut off valve.

This charcoal filter is a genuine OEM replacement part that is compatible with various models of microwave. It has a length of approximately 8 inches by 5 inches. The filter is designed to absorb odors, grease, and smoke generated during cooking and vent them outside or recirculate clean air back into the kitchen. The charcoal filter consists of activated charcoal, which is highly effective at trapping airborne particles. If there is a persistent odor in the kitchen even after cleaning the microwave and surrounding area, it may indicate that the charcoal filter is saturated and no longer effective. Additionally, if there is visible damage to the filter, such as cracks or holes, the filter should be replaced. It is recommended to replace the filter every 6 months.

This washer lid lock assembly is designed for top-load washing machines and ensures the lid remains securely closed during wash and spin cycles. It replaces worn or malfunctioning latches, helping prevent the machine from starting or pausing when the lid isn’t properly shut. The assembly includes the solenoid mechanism that engages the lock, contributing to safe and efficient operation. Compatible with a wide range of models, it’s an ideal solution for restoring reliable performance to your appliance.

This long oven sensor is also commonly known as a temperature sensor. It is designed for use with ovens and ranges. It is similar to a thermostat; it measures and regulates the internal temperature of your oven cavity. There is an adapter at one end, a probe at the other, and they are connected by an insulated wire. The probe is approximately 7 inches long. You can test the sensor with a multi-meter for functionality. You need to check the model-specific manual to determine what the proper resistance is for your specific appliance. This oven sensor comes with two wire harness adapters and a set of instructions.

The bake element is located at the bottom of the oven and gives off heat in order to bake evenly. If you notice that the element is not heating up or is not cooking evenly, it could be because it is broken or burnt out. All you need for this simple repair is a small screwdriver. To complete this repair, you will need to first turn the oven off (or shut off the house circuit breaker), remove the two screws that are holding the old element in place, remove the two wires from the old part, and then connect them to the new part and screw back into place.