Thermador Oven Parts

Thermador Oven MICROSWITCH This microswitch, also known as a safety switch, is a genuine OEM replacement part for use in microwaves. It is a highly sensitive switch which responds to slight changes in pressure or position, and ensures that the microwave only operates when the door is shut. The switch can fail due to physical damage or electrical failure, resulting in difficulties closing the door, and turning on the appliance. To remove the faulty switch, disconnect the wiring connectors and take note of where they are positioned. Place the new switch in position and reattach the wiring connectors to the appropriate terminals and close the microwave door to check that the switch engages appropriately.

Thermador Oven SENSOR This temperature sensor is an OEM replacement part designed for use in ovens/ranges. The sensor detects the temperature inside the oven and relays this information to the control board, which controls the heating elements in the oven. If the sensor experiences electrical failure or mechanical damage, you will likely notice uneven cooking, inaccurate temperature readings, and difficulties heating up the oven. You can access the sensor by either removing the back panel of your appliance or by reaching through the oven/range cavity from the front. Carefully disconnect the wires attached to the sensor and pull the sensor out of the appliance. Mount the new sensor in the correct position and reconnect the wires appropriately.

Thermador Oven HEATER-ELEMENT This OEM heater element, or bake element, is approximately 22 inches wide and generates heat in your oven for cooking and baking. It is commonly located at the bottom of the oven. The element is secured to a bracket with two screws and connects to the power source. You may suspect a faulty element if your oven cooks food unevenly or fails to heat up. If the element has breaks, bulges, or holes in the heating coil, it needs to be replaced. To check if it has shorted out, use a multimeter in continuity mode or the lowest ohms setting. Touch the probes to the wire terminals. A functioning element should cause the multimeter to beep or display a reading of approximately 10 to 75 ohms. To replace the element, start by shutting off the oven at the circuit breaker and unplugging the appliance. Open the oven door and pull out the racks. Unthread the screws at the back of the oven using a screwdriver. Gently pull the element out to access the wiring behind it, ensuring not to pull out any insulation or lose the wires in the insulation or behind the stove. Please keep in mind that this replacement part does not come with any accompanying hardware.

Thermador Oven SENSOR

Thermador Oven SHELF

Thermador Oven FUSE

Thermador Oven HEATER-ELEMENT This 27-inch heating element features two terminals with support brackets that connect to compatible 27-inch ovens. This heating element is a genuine OEM part that is sold individually without any other parts or hardware. If you notice your oven/range is not heating up effectively or at all or is heating certain parts within your range and not heating others, this element is likely the reason why. Replacing this heating element is quite simple and only requires that you turn off and disconnect your oven from power before unscrewing and disconnecting the old heating element. With the old element removed, you should inspect the terminals connecting within the oven for corrosion, arcing, and general damage. Then you can install the new heating element, connect the range to power and test the element with a thermometer and toast to check the browning level throughout the interior of the oven.

Thermador Oven HEATER-ELEMENT This is a 27-inch heating element that is designed for use within various makes and models of ovens and is a genuine OEM part that heats the appliance. This heating element comes with the necessary support brackets on the terminals to attach within your range. If you find that your range/oven is not heating evenly, taking noticeably longer to heat up, or simply not heating at all during the bake setting or is burnt out, you will need to replace the element immediately. Replacing this heating element is easy and only involves you disconnecting the range/oven from its wall outlet and using a screwdriver to disconnect and remove the element support bracket, allowing you to replace it. But before you replace your old element with the new, inspect the terminals within your oven for any sign of arcing, corrosion, or damage.

Thermador Oven SEAL-DOOR

Thermador Oven TANK

★★★★★

★★★★★

1 Review