Hardwick Oven Parts
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Hardwick Oven Parts
Your Price
$57.79
In Stock
Hardwick Oven Flat Style Igniter Kit
PartSelect Number PS1573892
Manufacturer Part Number 12400035
The flat style oven igniter kit is used in gas ovens and ranges. It is what provides the heat needed to open the gas valve, and it ignites fuel for the burner assembly. This part can be used for both bake and broil elements, and it can replace both short and long igniters. However, it cannot replace round style oven igniters. If your igniter glows for 90 seconds or more without igniting the burner, this means it is too weak to open the valve. The element in your igniter may have shorted it and it might not glow at all, or it might only glow orange or red. It needs to glow white hot; if it cannot get hot enough the gas will not be released from the safety valve and it will be impossible to light the burner in your oven. This kit includes the igniter, ceramic wire nuts, an insulation pad, a metal bracket, a variety of plug ends, and an instruction sheet. The body length is 3 3/4 inches, and the element inside is approximately 1 1/2 inches. This replacement part has an amperage range of 3.3 to 3.6. The element inside this igniter is extremely fragile, do not touch it. Before you start repairing your oven or range, make sure you have unplugged it and shut off the gas supply.
Fixes these symptoms
- Element will not heat
- Gas igniter glows, but will not light
- Gas smell
- See more...
Installation Instructions
James from Ferndale, MI
Oven would not work but the Broiler did
The oven had been working intermittently for a while and after repeated threats of starvation from my spouse I finally took a look even though it was summer and the grill was working fine. The Igniter would glow red when the oven was turned on but the gas would not flow to it no matter what the temperature setting. I searched online and found this site that explained it was possible for the igniter to glow but if it was not drawing the correct amperage (because its resistance was too high) then the main brain would not allow the gas valve to open. So I took a look at the broiler and it had the same igniter. I measure the resistance of both of them and the oven igniters resistance was higher (don't rememeber the reading) then I moved the Igniter from the broiler to the oven and the oven worked from there it was just a matter of ordering the part. End of story except for I am still doing all the cooking on the barbecue outside.
Read more...
Your Price
$103.52
In Stock
Hardwick Oven Range Bake Element
Then I connected the two wires on the new element. I pushed the wires back in the insulation in the wall of the cabinet. Then I inserted the two screws and tightened them in.
SUPER EASY!!!!!
This $40 part saved me $1500 on a new double wall oven. Read more...
PartSelect Number PS11757472
Manufacturer Part Number WPY04000066
The bake element is the heating element that is found at the bottom of the oven and is responsible for 90 percent of the bake heating. This spade style bake element is 16 inches wide, and connects with push-on wire terminals. It has a terminal depth of three inches and a total element length of nineteen inches. You may need to replace the heating element if your oven produces little to no heat, the oven will not heat evenly, or the element will not heat at all. This element comes with an instructions sheet and is intended for use with electric ovens. To see if this part will fit your oven, please check the list of compatible brands below.
Fixes these symptoms
- Element will not heat
- Little to no heat when baking
- Oven is too hot
- See more...
Installation Instructions
DENISE from GERMANTOWN, TN
bottom heating element in oven disintegrated
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I threw away the old pieces.Then I connected the two wires on the new element. I pushed the wires back in the insulation in the wall of the cabinet. Then I inserted the two screws and tightened them in.
SUPER EASY!!!!!
This $40 part saved me $1500 on a new double wall oven. Read more...
Your Price
$37.51
In Stock
Hardwick Oven 2 Piece Broiler Pan
shipment & arrival of new parts unbelievably fast....thanks Read more...
PartSelect Number PS971245
Manufacturer Part Number 4396923
This is cookware designed for use in your range or oven. It is a two-piece dish that is used to grill or cook food while the broil function is on, meaning it can withstand high temperatures. This set includes both the pan and the grid. The grid is the top part. The slotted design allows grease to easily drip into to the pan below. Not only does it catch all of the drippings, it also prevents splatter and smoke while cooking. The pan can also be used separately for baking and roasting. This cookware features a durable porcelain finish, which means it is incredibly easy to clean, and is dishwasher safe. It is roughly 1.5 inches deep, and measures approximately 16.5 inches by 12.5 inches. If your two-piece broil plan is lost, rusted, or damaged this is the replacement you need.
Installation Instructions
Lois from Elmer, NJ
Bought house & stove was missing rack & broiler
slid in grooveshipment & arrival of new parts unbelievably fast....thanks Read more...
Your Price
$71.04
In Stock
Hardwick Oven Door Seal - Top
The (1) gasket ordered for the "horizontal"/upper position was an exact replacement and fit like a charm.
However, the pair of (2) gaskets ordered for the "vertical"/sides position were not designed for this range and needed MODIFICATION in order to be installed. Specifically, the metal strips at the end of the gaskets were TOO WIDE to fit into the existing holes in the oven frame.
I was able to make the metal strips Using a pair of needle-nose pliers and a pair of nipper-pliers, I was able to flaten-out each of the four metal strips, cut each metal strip [basically in half], re-bend the halfed-strips into "hook" shapes, and then re-insert the metal hooks into the existing 3/16" holes.
So far, so good; no complaints from the tenant! Read more...
PartSelect Number PS11743943
Manufacturer Part Number WP7212P006-60
This oven door seal creates a protective seal around an oven door to prevent heat from running out of a closed oven and keeps room air from entering the oven. This part is 17.5 inches long and made of rubber. The metal hook on both ends of the seal is there to keep it in place. Remove screws to take off old seal using pliers and replace it with the new seal. For detailed installation instructions and accurate guidance, refer to the diagram provided by the manufacturer. As a safety precaution make sure to unplug oven from power source and wait for oven to cool before starting this replacement project.
Installation Instructions
David from Albany, NY
Tenant complaind that oven door gaskets were worn out.
No "repair" needed, just parts replacement. The oven door had (3) rubber-like gasket strips, held in place by metal strips at each end of the gaskets, which fit into 3/16" diameter holes in the oven frame. The (1) gasket ordered for the "horizontal"/upper position was an exact replacement and fit like a charm.
However, the pair of (2) gaskets ordered for the "vertical"/sides position were not designed for this range and needed MODIFICATION in order to be installed. Specifically, the metal strips at the end of the gaskets were TOO WIDE to fit into the existing holes in the oven frame.
I was able to make the metal strips Using a pair of needle-nose pliers and a pair of nipper-pliers, I was able to flaten-out each of the four metal strips, cut each metal strip [basically in half], re-bend the halfed-strips into "hook" shapes, and then re-insert the metal hooks into the existing 3/16" holes.
So far, so good; no complaints from the tenant! Read more...
Your Price
$14.20
Special Order
Hardwick Oven Glass Clip - Black
PartSelect Number PS1643208
Manufacturer Part Number 7112P093-60
The glass clip for your oven helps to hold the exterior glass in place. If you notice that your exterior glass is askew, or will not stay in place, you may need to replace the glass clip. This clip is just over an inch in height, and 1 inch in width. This part is made of black plastic and is square on the bottom, but triangular on the top. This is an OEM part sourced directly from the manufacturer. This product is sold individually. When ordering you will have to enter the order quantity.
Installation Instructions
Janellen from Aiken, SC
blower motor died
Pulled the motor and blower wheel from below. Replaced both. I think it was easier to replace the two together than just the motor.I also had old light indicators so we replaced them since the stove was sort of apart. The repair was not difficult at all, and my 30+ stove top looks and runs great!
Read more...
Your Price
$55.75
In Stock
Hardwick Oven Indicator Light Kit
PartSelect Number PS2079029
Manufacturer Part Number 715396K
This indicator light kit comes with two red jewel light lenses.
Your Price
$126.83
In Stock
Hardwick Oven Door Seal
PartSelect Number PS11743839
Manufacturer Part Number WP701650
This oven door seal is twenty-one inches wide. This woven style door gasket is gray in color.
Installation Instructions
Rosemary from Pawleys Island, SC
seal was black and stiff from burned in spilled grease and sauce
Unscrewed and pulled the door off and then took the three layers of the door apart in order to clean off the burned-on goop and remove the old and insert the new seal. The last screw was rusted in and the drill stripped it so that it was impossible to remove. I levered the remaining two layers apart, holding them open with screw drivers, and inserted the new seal. Had to be careful with the shaping of the metal core of the seal and the distribution of the sealing fabric. Phew! I saved the screws from each layer separately by taping them to the counter in the order of removal. This made reassembly easier. Getting the door back on was a bit difficult and I needed another pair of hands to help me.
Read more...
Your Price
$69.86
In Stock
Your Price
$7.11
In Stock
Hardwick Oven NUT- SNAP
PartSelect Number PS11743921
Manufacturer Part Number WP7103P114-60
This is an OEM part sourced directly from the manufacturer. This snap nut is round, and is made of black plastic. It is approximately half an inch in diameter. This snap nut should snap into place, rather than being screwed in. This product is designed for use in the door of your range/stove/oven. Many of our customers have rated this repair as easy. This part is sold individually.
Hardwick Oven Appliance Types
- Hardwick Cooktop Parts
- Hardwick Freezer Parts
- Hardwick Grill Smoker Parts
- Hardwick Microwave Parts
- Hardwick Parts
- Hardwick Range Parts
Popular Hardwick Oven Models
Below are the most popular Hardwick Oven models we have. Enter your model number in the search box to find your model.
- SKJ7141819DE Wall, Continuous-Clean, Gas
- CKD7122810AC Wall, Standard, Gas
- CJ7141819DE Wall, Standard, Gas
- CJ7141809RC Wall, Standard, Gas
- CG7241A819R Wall, Continuous-Clean, Gas
- EPF7-31819AE
- SH7241819R Wall, Standard, Gas
- EE7-11819R Wall, Electric
- CKD7224810AC Wall, Standard, Gas
- EF7-11819AE Wall, Electric
- CKD7121810AC Wall, Continuous-Clean, Gas
- CG8422MW729RG Wall, Standard, Double, Gas
- CKD7221819A Wall, Continuous-Clean, Gas
- CH7241819R Wall, Continuous-Clean, Gas
- CG8422MY729RG Wall, Standard, Double, Gas
- CJ7122809RC Wall, Standard, Gas
- BEV7110 Wall, Electric
- CKG8421MW729RG Wall, Standard, Double, Gas
- EPE7-31819AE Wall, Electric
- CKD7222819A Wall, Standard, Gas
