My Orders
Hammer Drill Parts
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
Shop By Brand
View More
Popular Hammer Drill Parts
Length: 8'
Gauge: 18
Wires: 2
Type: Bare Wire
This cord is a genuine DeWalt replacement part. This cord is compatible with the list of models below. This part is made for double insulated tools It is a two wire cord with two prongs and does not need a ground wire. The cord is sold individually. Installation of this part requires the new cord wires to go correctly into wire terminals also routing the cord and wires in the right path can help avoid pinching when the tool case (Plate) is put back into place.
Length: 8'
Gauge: 18
Wires: 2
Type: Bare Wire
This cord is a genuine DeWalt replacement part. This cord is compatible with the list of models below. This part is made for double insulated tools It is a two wire cord with two prongs and does not need a ground wire. The cord is sold individually. Installation of this part requires the new cord wires to go correctly into wire terminals also routing the cord and wires in the right path can help avoid pinching when the tool case (Plate) is put back into place.
This Ball Bearing is sealed on both sides. It is a genuine replacement part and is sold individually.
Ball bearings are used to reduce friction between rotating parts.
The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. This reduces wear on the tool and allows it to run smoothly.
Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.
This Ball Bearing is sealed on both sides. It is a genuine replacement part and is sold individually.
Ball bearings are used to reduce friction between rotating parts.
The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. This reduces wear on the tool and allows it to run smoothly.
Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.
Genuine Makita replacement part. Set of 2 Carbon Brushes with wire lead attached. • Worn brushes are often the cause of a poorly running motor • Replacing brushes can fix an intermittent motor • New brushes can restore a motor's electric braking Carbon motor brushes are one of the most commonly replaced power tool components. Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power. A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned. When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.
Genuine Makita replacement part. Set of 2 Carbon Brushes with wire lead attached. • Worn brushes are often the cause of a poorly running motor • Replacing brushes can fix an intermittent motor • New brushes can restore a motor's electric braking Carbon motor brushes are one of the most commonly replaced power tool components. Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power. A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned. When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.
Length 8 Foot
Length: 6'
Gauge: 18
Wires: 2
Type: Bare Wire
This power supply cord is a genuine OEM sourced replacement part. It is specially made to supply power from a standard outlet to Makita power tools. A cracked or damaged cord should be replaced before continuing to use the tool. This rubber insulated cord is sold individually. It comes with a rubber sleeve grommet that is not sold separately.
Replacing this power supply cord you will need a screwdriver.
• Remove the housing screws
• Remove the the housing
• Disconnect the old cord wires
• Remove the old power cord
• Secure the new cord in place
• Connect the wires
• Reassemble and test the new cord
Length 8 Foot
Length: 6'
Gauge: 18
Wires: 2
Type: Bare Wire
This power supply cord is a genuine OEM sourced replacement part. It is specially made to supply power from a standard outlet to Makita power tools. A cracked or damaged cord should be replaced before continuing to use the tool. This rubber insulated cord is sold individually. It comes with a rubber sleeve grommet that is not sold separately.
Replacing this power supply cord you will need a screwdriver.
• Remove the housing screws
• Remove the the housing
• Disconnect the old cord wires
• Remove the old power cord
• Secure the new cord in place
• Connect the wires
• Reassemble and test the new cord
Installation Instructions
Bruce from HILLSBORO, OR
Old power cord frayed at the grommet entering the drill casing
Did not do repair as replacement part did not match description on partselect website. The grommet is not part of the replacement that was sent. Order #22962198
Email sent (11/16/2023) to partselect.com has gone unanswered
Thanks?
Email sent (11/16/2023) to partselect.com has gone unanswered
Thanks?
This set includes 2 Carbon Brushes with wire leads and brush springs attached. The set contains genuine Makita replacement parts, and comes packaged in a retail box. This brush set will fit the Makita tools listed at the bottom of the page. • Worn brushes frequently are the cause behind a motor running poorly. • Replacing brushes can fix a motor that's operating intermittently. • New brushes can restore a motor's electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.
This set includes 2 Carbon Brushes with wire leads and brush springs attached. The set contains genuine Makita replacement parts, and comes packaged in a retail box. This brush set will fit the Makita tools listed at the bottom of the page. • Worn brushes frequently are the cause behind a motor running poorly. • Replacing brushes can fix a motor that's operating intermittently. • New brushes can restore a motor's electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
This is a genuine brush set designed for use with Milwaukee rotary hammers. This assembly includes two (2) carbon brushes with lead wires attached. Please note brush holders are sold separately. Due to prolonged contact with an armature brushes will gradually wear down and will require replacement. It is advised to replace both brushes at the same type. To complete this repair you would need a screwdriver. • Make sure the unit is unplugged • Remove screws from the housing to gain access to the armature and brushes • Remove old brushes and secure the new ones in brush holders • Re-assemble and test the tool
This is a genuine brush set designed for use with Milwaukee rotary hammers. This assembly includes two (2) carbon brushes with lead wires attached. Please note brush holders are sold separately. Due to prolonged contact with an armature brushes will gradually wear down and will require replacement. It is advised to replace both brushes at the same type. To complete this repair you would need a screwdriver. • Make sure the unit is unplugged • Remove screws from the housing to gain access to the armature and brushes • Remove old brushes and secure the new ones in brush holders • Re-assemble and test the tool
This is a genuine OEM replacement part, it is sold individually. This Ball Bearing is sealed on both sides. • Ball bearings are used to reduce friction between rotating parts. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. • This reduces wear on the tool and allows it to run smoothly. • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.
This is a genuine OEM replacement part, it is sold individually. This Ball Bearing is sealed on both sides. • Ball bearings are used to reduce friction between rotating parts. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. • This reduces wear on the tool and allows it to run smoothly. • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.
This is a 1/2-inch OEM keyless chuck for hammer drills, allowing users to swiftly change drill bits and attachments without requiring a chuck key. Due to the mechanical stresses it undergoes, the jaws of the chuck can break or wear significantly, resulting in a loss of grip or excessive play. If you encounter difficulty tightening or loosening the chuck jaws on your drill or notice wobbling during operation, replacement is necessary. To replace this chuck assembly, you will need a screwdriver or drill to remove the initial left-handed screw on the inside. To completely remove the chuck, it is recommended that you secure the drill in a vise or use the drill itself, along with an Allen key, to detach the main chuck assembly from the drill. Once the old chuck is removed, you can effortlessly install the new chuck along with its securing screw. Please note that this chuck assembly is sold individually and does not include any additional securing hardware that may be required.
This is a 1/2-inch OEM keyless chuck for hammer drills, allowing users to swiftly change drill bits and attachments without requiring a chuck key. Due to the mechanical stresses it undergoes, the jaws of the chuck can break or wear significantly, resulting in a loss of grip or excessive play. If you encounter difficulty tightening or loosening the chuck jaws on your drill or notice wobbling during operation, replacement is necessary. To replace this chuck assembly, you will need a screwdriver or drill to remove the initial left-handed screw on the inside. To completely remove the chuck, it is recommended that you secure the drill in a vise or use the drill itself, along with an Allen key, to detach the main chuck assembly from the drill. Once the old chuck is removed, you can effortlessly install the new chuck along with its securing screw. Please note that this chuck assembly is sold individually and does not include any additional securing hardware that may be required.
Genuine Milwaukee replacement part, this item is sold individually. This Chuck Key tightens the jaws of the 1/2 inch capacity Chucks on all the Drill models shown below. For convenience a Chuck Key Holder part number 48-66-4040 can be ordered. It is attached to the power cord then the Chuck Key is attached to it.
Genuine Milwaukee replacement part, this item is sold individually. This Chuck Key tightens the jaws of the 1/2 inch capacity Chucks on all the Drill models shown below. For convenience a Chuck Key Holder part number 48-66-4040 can be ordered. It is attached to the power cord then the Chuck Key is attached to it.
This cord protector is a genuine Milwaukee replacement part and is sold individually. Cord Protectors are designed to slide onto your cord and fit securely at the end, where it's firm rubber will protect the base of the cord from getting bent and pinched, which can expose the wires and become a safety hazard.
This cord protector is a genuine Milwaukee replacement part and is sold individually. Cord Protectors are designed to slide onto your cord and fit securely at the end, where it's firm rubber will protect the base of the cord from getting bent and pinched, which can expose the wires and become a safety hazard.