Log Splitter Parts

Why Genuine OEM Matters

Shop By Brand Shop By Part Type

Popular Log Splitter Parts

Snow Blower Carburetor Gasket – Part Number: 951-11569A

Your Price

$6.22

Log Splitter Snow Blower Carburetor Gasket

PartSelect Number PS9170612

Manufacturer Part Number 951-11569A

Log Splitter Spider Bushing – Part Number: 735-04103

Your Price

$18.02

Log Splitter Spider Bushing

PartSelect Number PS9106439

Manufacturer Part Number 735-04103

This rubber and plastic spider bushing is a genuine OEM part for various makes of log splitters and is sold as an individual part. Measuring at approximately 2-inches by 2-inches, this bushing is attached to the motor or drive shaft and is used to support the rotating shaft and other components, all while allowing smooth rotation and proper alignment. The spider bushing rides between the couplings, connecting the engine and the hydraulic pump. If you notice excessive vibrations from the motor, check the drive motor shaft for a cracked bushing or couplings, since they work together and are often replaced at the same time.

Log Splitter Coupling – Part Number: 718-04395

Your Price

$23.29

Log Splitter Coupling

PartSelect Number PS9299988

Manufacturer Part Number 718-04395

Lawn Mower Drive Belt – Part Number: 954-04032B

Your Price

$26.85

Log Splitter Lawn Mower Drive Belt

★★★★★

1 Review

PartSelect Number PS9172714

Manufacturer Part Number 954-04032B

3/8 x 36-1/8-inch This ground drive belt (part number 954-04032B) is for lawn mowers. Ground drive belt 954-04032B drives the transmission, which propels the lawn mower wheels. Wear work gloves to protect your hands when installing this part.

Log Splitter Coupling – Part Number: 718-04392

Your Price

$16.63

Log Splitter Coupling

PartSelect Number PS9095317

Manufacturer Part Number 718-04392

This coupler connects the engine or motor to the hydraulic pump in your lawn equipment. It has a 0.5-inch inside diameter and is typically located near the rear coupling support bracket. If the coupler is broken, you will notice excessive play, cracks, or a loss of power transmission. Failure to replace a broken coupler can result in reduced power, poor operation, or complete equipment failure. To remove the coupling from your machine, remove any retaining bolts, screws, or clamps securing it in place using a wrench or socket. Afterward, gently wiggle or twist the coupling to release it. This replacement part is sourced directly from its original equipment manufacturer and is sold individually.

Lawn Mower Air Valve – Part Number: 934-0255

Your Price

$5.95

Log Splitter Lawn Mower Air Valve

★★★★★

1 Review

PartSelect Number PS9311038

Manufacturer Part Number 934-0255

Log Splitter Back Plate – Part Number: 781-0790A-0637

Your Price

$45.43

Log Splitter Back Plate

PartSelect Number PS9130747

Manufacturer Part Number 781-0790A-0637

This back plate, also known as a wedge plate, is sourced directly from the manufacturer for use in log splitters. It is a flat, metal plate found at the rear end of the machine, with a length of 8 inches and a width of 2 inches. It provides support and stability to the log splitter during use. The plate may fail due to excessive stress, physical damage, or corrosion. If the plate has cracks, or bends, the log splitter will become unstable and unsafe to operate. The internal components of the log splitter may also fall out of alignment and cause further damage to the equipment. Use a wrench to remove the fasteners that secure the plate to the log splitter frame. Clean the mounting area and install the new plate. Reinstall the fasteners and be careful not to overtighten them as this can damage the surface of the plate.

Air Cleaner Housing Assembly – Part Number: 951-14439

Your Price

$40.98

Log Splitter Air Cleaner Housing Assembly

PartSelect Number PS11813659

Manufacturer Part Number 951-14439

Chipper / Shredder Adjustable Gib – Part Number: 781-0351

Your Price

$20.98

Log Splitter Chipper / Shredder Adjustable Gib

★★★★★

1 Review

PartSelect Number PS9305203

Manufacturer Part Number 781-0351

The Adjustable Gib (Keyway) is a gray, metal, 2 inch, individually sold part rated as easy to install by consumers. It locks two shafts together so they can rotate. You will know if you need to replace this part if the shaft is freely spinning and will not spin with the drive shaft. You can see this happening when the shaft is turning, or you can turn the shaft by hand to see if the two parts connect. The part is attached between the two shafts.