Troy-Bilt Log Splitter Parts

This rubber and plastic spider bushing is a genuine OEM part for various makes of log splitters and is sold as an individual part. Measuring at approximately 2-inches by 2-inches, this bushing is attached to the motor or drive shaft and is used to support the rotating shaft and other components, all while allowing smooth rotation and proper alignment. The spider bushing rides between the couplings, connecting the engine and the hydraulic pump. If you notice excessive vibrations from the motor, check the drive motor shaft for a cracked bushing or couplings, since they work together and are often replaced at the same time.

This genuine flat washer distributes fastener pressure across the mounting surface and may also serve as a spacer in compatible outdoor power equipment assemblies. It measures 0.385 of an inch across the inner opening,0.870 of an inch across the outer edge, and 0.090 of an inch thick. This washer is sold individually, and you should confirm the equipment you are repairing matches with this washer before ordering.

This is a genuine OEM replacement part, it is sold individually. The purpose of this filter is to help eliminate dirt, dust and debris from contaminating the carburetor and damaging the engine. A dirty air filter can cause the engine from operating properly. This filter can be cleaned a time or two by using an air supply. But it is advised to replace it once it becomes dirty.

This authentic OEM air filter assembly includes a pleated paper air filter and a foam pre-filter. It is located in the air cleaner housing of your lawn equipment. Its purpose is to filter out dust and debris, ensuring that the engine receives clean air for efficient fuel combustion. If your filter is clogged or torn, it is necessary to replace it. A clogged or damaged filter can cause difficulties when starting your machine. It can also lead to increased fuel consumption, costly repairs, and potential engine failure. To replace the filter, locate the air cleaner housing, remove the cover by pressing the push tab and lifting it up, then take off the air filter from its base. This assembly is sold individually.

This coupler connects the engine or motor to the hydraulic pump in your lawn equipment. It has a 0.5-inch inside diameter and is typically located near the rear coupling support bracket. If the coupler is broken, you will notice excessive play, cracks, or a loss of power transmission. Failure to replace a broken coupler can result in reduced power, poor operation, or complete equipment failure. To remove the coupling from your machine, remove any retaining bolts, screws, or clamps securing it in place using a wrench or socket. Afterward, gently wiggle or twist the coupling to release it. This replacement part is sourced directly from its original equipment manufacturer and is sold individually.

This genuine manufacturer-sourced component is specially made for use with MTD and Troy-Bilt log splitters. It is an identical replacement for a missing or a faulty coupling that was installed on a new unit. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind this high-quality part is made of durable metal and is sold individually. Note, the other #718-04392 Coupling, . 500 is sold separately.

An authentic item that is supplied directly from the original equipment manufacturer for use with Yard Machines and MTD lawn and garden equipment. It is a high-quality replacement for a missing or worn filter assembly which helps to remove harmful contaminants from the air that is supplied in the engine. Please note this part is sold individually, it includes the main pleated paper filter and the foam pre-filter.

This Cotter Pin is a silver 5/32x1-1/4 metal part, sold individually and certified by the original equipment manufacturer. It connects to the axel shaft after the wheel and washer have been installed but before the hub cap. It is used to prevent the wheel from falling off, and if it breaks (due to fatigue) the wheel will fall off. Check your model number for the correct size of replacement cotter pin to know you are ordering the correct model. This is a one-time use product, which should be replaced during any other repair in which it is disturbed or dislodged.

This gray metal adjustable gib fits between two shafts and locks them together so they turn as one. It is 2 inches long and sold individually. Replace it if one shaft spins freely without turning the drive shaft. Turn off the machine and disconnect power before repair. Check the model number before ordering.