MTD Log Splitter Parts
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular MTD Log Splitter Parts
MTD Log Splitter Snow Blower Carburetor Gasket
PartSelect Number PS9170612
Manufacturer Part Number 951-11569A
MTD Log Splitter Spider Bushing
PartSelect Number PS9106439
Manufacturer Part Number 735-04103
This rubber and plastic spider bushing is a genuine OEM part for various makes of log splitters and is sold as an individual part. Measuring at approximately 2-inches by 2-inches, this bushing is attached to the motor or drive shaft and is used to support the rotating shaft and other components, all while allowing smooth rotation and proper alignment. The spider bushing rides between the couplings, connecting the engine and the hydraulic pump. If you notice excessive vibrations from the motor, check the drive motor shaft for a cracked bushing or couplings, since they work together and are often replaced at the same time.
MTD Log Splitter Lawn Mower Drive Belt
PartSelect Number PS9172714
Manufacturer Part Number 954-04032B
This genuine drive belt is an original replacement part sourced directly from the manufacturer and is commonly used in Craftsman lawn mowers and edgers. Made from flexible rubber, it transfers power from the engine to the pulley that drives the cutting blades. Over time, the belt may become brittle or cracked due to wear and exposure, requiring replacement to maintain optimal performance. Measuring 3L x 35.80 inches, this belt is sold individually. A wrench may be needed for installation, depending on your equipment model.
MTD Log Splitter Coupling
PartSelect Number PS9095317
Manufacturer Part Number 718-04392
This coupler connects the engine or motor to the hydraulic pump in your lawn equipment. It has a 0.5-inch inside diameter and is typically located near the rear coupling support bracket. If the coupler is broken, you will notice excessive play, cracks, or a loss of power transmission. Failure to replace a broken coupler can result in reduced power, poor operation, or complete equipment failure. To remove the coupling from your machine, remove any retaining bolts, screws, or clamps securing it in place using a wrench or socket. Afterward, gently wiggle or twist the coupling to release it. This replacement part is sourced directly from its original equipment manufacturer and is sold individually.
MTD Log Splitter Air Cleaner Housing Assembly
PartSelect Number PS11813659
Manufacturer Part Number 951-14439
Introducing the MTD Air Cleaner Housing Assembly, a necessary component for your lawn and garden equipment engines. Specifically designed to house the air filter for your engine, this product ensures optimal performance and longevity of your engine by maintaining clean air for combustion. Constructed with top-quality materials by MTD, this assembly enhances the overall efficiency of your equipment. Be sure to put on your work gloves while installing this part to ensure maximum hand safety. Trust MTD's commitment to quality and innovation. Improve your engine's health today with our air cleaner housing assembly.
MTD Log Splitter Back Plate
PartSelect Number PS9130747
Manufacturer Part Number 781-0790A-0637
This back plate, also known as a wedge plate, is sourced directly from the manufacturer for use in log splitters. It is a flat, metal plate found at the rear end of the machine, with a length of 8 inches and a width of 2 inches. It provides support and stability to the log splitter during use. The plate may fail due to excessive stress, physical damage, or corrosion. If the plate has cracks, or bends, the log splitter will become unstable and unsafe to operate. The internal components of the log splitter may also fall out of alignment and cause further damage to the equipment. Use a wrench to remove the fasteners that secure the plate to the log splitter frame. Clean the mounting area and install the new plate. Reinstall the fasteners and be careful not to overtighten them as this can damage the surface of the plate.
MTD Log Splitter Chipper / Shredder Adjustable Gib
PartSelect Number PS9305203
Manufacturer Part Number 781-0351
Introducing the Adjustable Gib by MTD, a vital component for your log splitter. This 2'' long spacer is designed to be positioned between the wedge assembly and back plate of your log splitter. Its role is crucial for the seamless operation of your equipment, ensuring maximum productivity. Should your gib be worn or damaged, a replacement is readily at hand to take its place. To ensure safety during installation, it is recommended to wear work gloves. Upgrade your log splitter's performance today with our MTD Adjustable Gib.
MTD Log Splitter Appliance Types
Related MTD Log Splitter Parts
- MTD Log Splitter Belts
- MTD Log Splitter Hoses and Tubes
- MTD Log Splitter Latches
- MTD Log Splitter Oil Plugs
- MTD Log Splitter Pumps
- MTD Log Splitter Spark Plugs
Popular MTD Log Splitter Models
Below are the most popular MTD Log Splitter models we have. Enter your model number in the search box to find your model.
- 530 Log Splitter
- 24BF560D062 Wood Splitter
- 24BF560D062 Wood Splitter
- 630 Log Splitter
- 24AF550C000 Log Splitter
- 24AD586B000 Log Splitter
- 24AF572B729 Log Splitter
- 560 Log Splitter
- 510 Log Splitter
- 511 Log Splitter
- 24BF510B105 Log Splitter
- 24BF550M006 Log Spillter
- 24BF550M006 Mtd Log Splitter
- 24BF552B729 25 Ton Splitter
- 622 Log Splitter
- 24AA510A022 Log Splitter
- 24AA510A022 MTD Log Splitter Model 24AA510A022 Parts
- 24BG57M3004 27 Ton Log Splitter
- 24BG57M3004 Mtd Gold Log Splitter
- 550THRU570 Log Splitter