Hotpoint Oven Parts

Hotpoint Appliance Parts
Shop By Appliance Type

Popular Hotpoint Oven Parts

Your Price
$31.18
  In Stock
Bake Element - 240V
★★★★★
★★★★★
(75)
PartSelect Number PS249424
Manufacturer Part Number WB44X200
This is a 240 volt bake element for your oven or range. The kit comes with two installation screws and the element. The element functions by supplying heat from the bottom of the oven to bake or cook your food. You may need to replace the bake element if your oven is not heating properly. This is a black metal part (Width 13 inches, length 16.5 inches, depth 1-1/2 inches ) which can be installed onto your range with a screwdriver. Installation is rated as "medium" difficulty. This element is the part that heats to allow cooking, and if broken or missing you'll be unable to cook. This part attaches to the lower section of the range. Refer to your model number and user manual to ensure this part is right for you. Each screw gets screwed into each wire terminal with a Phillips screw driver. Hold the wires forward to make sure the wires do not fall back through the rear of the oven. Unplug your appliance or shut off your circuit breaker to the appliance before installing the new part.
Fixes these symptoms
  • Element will not heat
  • Little to no heat when baking
  • Little to no heat when broiling
  • See more...
Installation Instructions
Beth from Matthews, NC
Replacment of the bake unit
The hardest part was removing the old nuthead screws off the old bake burner. Once those were off installing the new bake element was simple. One screw in each wire terminal, two hex head screws to hold the unit in place. Works like a charm! Read more...
Your Price
$14.72
  In Stock
40WATT 15AMP INCANDESCENT BULB
★★★★★
★★★★★
(5)
PartSelect Number PS217532
Manufacturer Part Number 40A15
Installation Instructions
J. Douglas from Grass Valley, CA
Broken plastic parts
Cleaned the refrigerator as the old parts were removed. Installed new parts as the old parts were removed so as to easily identify the replacement parts. Very easy and wife was extremely happy after old plastic parts self destructed over a period of months and refrigerator was essentially unusable on the bottom two drawers. Read more...
Your Price
$43.73
  In Stock
Broil Element
★★★★★
★★★★★
(21)
PartSelect Number PS249411
Manufacturer Part Number WB44X173
The broil element is located at the top of the oven and gives off heat in order to bake evenly. If you notice that the element is not heating up or is not cooking evenly it could be because it is broken or burnt out. The depth of the screw-on terminals is 2-3/4 inches and they are 1-1/4 inches apart. Does not include mounting bracket. All you need for this simple repair is small screwdriver. To complete this repair, you will need to first turn the oven off (or shut off the house circuit breaker), remove the two screws that are holding the old element in place, remove the two wires from the old part, and then connect them to the new part and screw back into place.
Fixes these symptoms
  • Element will not heat
  • Little to no heat when baking
  • Little to no heat when broiling
  • See more...
Installation Instructions
Harry from Rancho Santa Margarita, CA
Needed to replace cracked bake & broil element
This repair is very simple and only required about 15-20 minutes per unit. After turning off the power to your oven at the main breaker box, it's just a matter of removing two 1/4" screws and pulling out the units. The tricky part is removing the power plugs to the elements and not letting them slip back into the insulation. Once you plug in the new elements and screw them back in you are good to go. Once note, while you have everything out, it is a great opportunity to give your oven a good cleaning. Read more...
Your Price
$41.48
  In Stock
Bake Element - 220V 2300W
★★★★★
★★★★★
(67)
PartSelect Number PS249466
Manufacturer Part Number WB44X5082
This bake element goes in the bottom of your range and is 220 volts and 2300 watts. This closed hinged style element with screw-in terminals measures at 15-1/4 inches long and 18-1/4 inches wide. The bottom bake element provides heat for baking. Tools you will need for this repair include pliers, screwdrivers, and an adjustable wrench. Before you begin this installation, remember to shut off the house circuit breaker or unplug your range. For safety purposes we also recommend wearing work gloves.
Fixes these symptoms
  • Element will not heat
  • Little to no heat when baking
  • Little to no heat when broiling
  • See more...
Installation Instructions
Wilbur from Taylorville, IL
element quit working
Unhooked electrical wiring from unit and rehooked new unit to electrical wiring. Read more...
Your Price
$8.22
  In Stock
Light Cover
★★★★★
★★★★★
(8)
PartSelect Number PS247415
Manufacturer Part Number WB36X192
This light bulb lens covers the interior light bulb in an oven, range, or stove. No tools are necessary to replace this part. Simply slide off the wire bracket to remove the existing light bulb lens. Disconnect power to your appliance before this repair. It is recommended to check the light bulb while the lens cover is removed in case it needs to be replaced. Be sure to remove all broken glass, if applicable, before installing new lens. This part is sourced directly from the genuine manufacturer, and is sold individually.
Installation Instructions
Edward from Ashland, MA
I Tried to remove Oven Light and got a spark that took out the Control Panel.
Oven light was easy - Snapped the Wire Bail, removed the Glass Protect and removed the buld. Installed new bulb, installed Glass Protect and snapped the Wire Bail. The Control Panel was a little harder and had to remove the 4 screws holding the metal Back Plate cover. I wrote down all the wire connections and then unplugged the wires. I took a 1/4 nutdriver and removed 4 screws holding Control panel in place and removed the Panel. The new control panel did not come with the Switch Face Plate so I removed the old one with a razor blade. The Switch Face Plate had plenty of adhessive so I just aligned the Face Plate with the Control Panel and seated it in place - thankfully it held firmly. I installed the Control Panel with Face Plate into the range and secured it with 4 screws using nutdriver. I plugged the wire connectors into the Control Panel and installed the Metal Back Plate to the range and secured it with 4 screws. Plugged the Range into the sockets and checked it for operation. Everything worked Ok including the new oven light. Read more...
Your Price
$27.93
  In Stock
Broiler Pan - Large
★★★★★
★★★★★
(9)
PartSelect Number PS1517612
Manufacturer Part Number WB48X10056
This large broiler pan is found in the bottom of your oven and is used to catch drippings from broiling foods. This part includes the grate and bottom pan and is made of porcelain. The grate measures 15-1/2 inches wide by 13 inches deep and the pan is about 17 inches wide by 13 inches deep. No tools are required to replace this item, simply pull out the lower drawer of your range, pull down the front of the drawer, slide the pan out and slide the new one into place. This is a genuine part sourced right from the manufacturer.
Installation Instructions
kevin from miami, FL
missing trim and trim bracket
Attatched trim bracket to cabniet with screws that by the way were not supplied then attached plastic trim to bracket Read more...
Your Price
$9.57
  In Stock
Washer - 12 Pack
PartSelect Number PS234480
Manufacturer Part Number WB1X119D
Your Price
$6.24
  In Stock
RECEPTACLE PUSH-IN
★★★★★
★★★★★
(5)
PartSelect Number PS752188
Manufacturer Part Number WB08T10026
This part is the replacement light socket for your oven. The oven light socket provides power to the light, and at the same time holds the light bulb in place.
Installation Instructions
Richard from Menifee, CA
No problems encountered.
Used nutdriver to remove screws holding cover over oven light socket, unclipped electrical connectors, removed socket by hand, then reversed the foregoing. Easy. Read more...
Your Price
$8.22
  In Stock
Single Heating Element Support Clip
★★★★★
★★★★★
(6)
PartSelect Number PS243701
Manufacturer Part Number WB2X9719
The metallic clip, or also known as a broil element support, is for a oven element on a range. This part holds the broil element in place on top of the oven. If your support clip is broken then this replacement should be the solution. The tools needed for this project are slip joint pliers. For safety precautions, make sure to unplug your range from the power source, or shut off the house circuit breaker before starting this project. Refer to the installation instructions for best results and accuracy.
Fixes these symptoms
Installation Instructions
Paul from Canton, NY
broiling element had burned through, req. its replacement
First I removed the two screws that hold the element in place. I also removed a screw that held one end of a support bracket. I then pulled the element out about 3 inches and disconnected the two wires. Reversing these steps, I finished the element's replacement.

I had noticed that the former element was sagging at the front end. I installed the additional clips (not original) on each forward end of the element for additional support.
Read more...
Your Price
$108.94
  In Stock
Oven Sensor
★★★★★
★★★★★
(4)
PartSelect Number PS236043
Manufacturer Part Number WB21X5301
It is possible that your oven is cold because of a fault in the temperature sensor. The temperature sensor regulates oven temperature in modern ranges, like a thermostat. It is on the back wall near the broiler on the top wall. On a newer oven, there may be a fault code displayed. Faulty temperature sensors are often responsible for F3 and F4 error messages on an electric range. Check your manual or the manufacturer website to find out the proper resistance of the temperature sensor. To check your sensor, unplug the oven and use a multi-meter to see if your sensor is at the correct resistance.
Fixes these symptoms
  • Element will not heat
  • Little to no heat when baking
  • Oven is too hot
  • See more...
Installation Instructions
James from Austin, TX
Oven tempature was approximately 150 degrees to low
This repair is EASY if you know how to use an ohm meter. If not, seek help for this step.

SYMPTOM:
The oven (JKP27WOP3WG or JKP27WP3WG and many ovens like it ) was not getting hot enough. Verifying the cooking temperature with an typical oven thermometer, I was able to determine that the oven was cooking temperature was about 150 degrees to low.

FAILURE POINTS:
There are two logical failure points (1) The oven sensor ( WB21X5301 about $75), or the (2) the controller board (PS238233 about $252). In my case it was the controller board. When replaced the oven worked beautifully.

REPAIR:
As with any repair, you MUST DISCONNECT POWER TO THE UNIT BEFORE SERVICING!!!

Pull oven from the wall:
- Disconnect power by flipping the circuit breaker to the OFF position.
- Remove the top flange / cowling from the top of the oven (it just pulls off)
- Remove two screws under the top flange / cowling
- The whole unit easily slides out, but it is highly recommended that you use two people to place the oven on the floor.

As a diagnostic between these two parts, if the oven sensors measure approximately 1.1K ohms of resistance at room temperature, then it is probably not the sensor. The oven sensor wires are connected to two white wires that run up to the controller board. You need to disconnect the oven sensor to make the measurement. You may either completely remove the oven sensor by cutting the wire (be sure to allow yourself enough slack so that they may be safely reconnected) where it connects to the white wires, OR, (preferred method) if leaving the oven sensor partially installed,
- Remove the top sheet metal cover (10 screws)
- Remove the service connect cover (2 screws - this is where the main Power cord comes into the unit)
- Disconnect the white wires from the controller board (this connector which also includes other circuits is on the left side when looking at the controller board).
- Remove two screws from oven sensor but just let in dangle down so that you can put the sensor in the ice water / boiling water.

Measure the resistance under the following conditions. Your ohm meter should read APPROXIMATELY...
- 1.02K ohms in ice water
- 1.09K ohms at room temperature
- 1.36K ohms in boiling water.
If you get approximately these readings, then it is NOT the oven sensor. If that checks out then re-install the sensor AND the connector.

If it is NOT the sensor, replace the controller board.
- Take a moment to write down the color of the wire to the LETTERING (N, L, G, C / COM,,,) on the controller board. The connectors are in different locations on the new controller board so the wire color to the letter designation is significant.
- Carefully remove the wires one at a time
- VERY carefully remove the keypad ribbon cable from the right side of the controller board.
-- The ribbon cable will disconnect by releasing some little pressure clips on the side of the connector.
- Remove the controller board (4 screws)
- Install new controller board (4 screws)
- VERY carefully connect the keypad ribbon cable on the right side.
-- Make sure that the connector is in the OPEN position first, then,
-- Slide in the cable ensuring that all parts of the ribbon made it into the connector, then
-- Press down on the connector locking tabs.
- Reconnect each wire to the correctly lettering on the board.
-- Again, the connectors MAY BE in a different order on the replacement controller board. Match color to letter.
- Reconnect the (5 wire?) connector that includes the white oven sensor wires.
- Make sure everything looks normal, (i.e. no wires are pinched, remove tools from top of oven area, etc.)
- Re-install top cover.
- Re-install service connect cover.

You can test the unit while it is out of the cabinet,
- Make SURE that all sheet metal covers are in place.
- Flip power breaker to "On".
- Test that oven gets to the desired temp.
Read more...

Appliance Type

Popular Hotpoint Oven Models

Below are the most popular Hotpoint Oven models we have. Enter your model number in the search box to find your model.