Dynabrade Drill Parts
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Dynabrade Drill Parts
Your Price
$45.53
In Stock
Dynabrade Drill Blades
PartSelect Number PS10336584
Manufacturer Part Number 01480
These authentic OEM sourced replacement rotor blades are commonly used on Dynabrade sanders and grinders. They are attached to the rotor inside the tool pushing the air. This set includes (4) compound material blades per order. Replacing these blades you will need a set of wrenches and pliers.
Your Price
$47.76
In Stock
Dynabrade Drill Blades/rotor (4 Pack)
PartSelect Number PS10336518
Manufacturer Part Number 01011
These blades in your die grinders are located on the rotor within the motor housing. This OEM set includes four blades, each measuring approximately 1-1/2 inches by 3/8 inches. When the tool is turned on, the motor drives the rotor, causing the blades to spin rapidly and help you shape various materials. It is important to regularly check the condition of the blades and replace them if they are visibly worn out or misaligned. Additionally, pay attention to any unusual signs during operation, such as increased noise, vibration, or burning smells. To replace the blades, refer to your user manual for detailed instructions on how to disassemble the motor housing. Typically, you will need to secure the tool in a padded vise, then use an adjustable pin wrench to remove the lock ring. Proceed with disassembling the tool by removing the collet and rotor nut from the rotor shaft, followed by the cylinder, spacer, and the four blades from the rotor.
Your Price
$9.67
On Order
Dynabrade Drill Seal
PartSelect Number PS10336573
Manufacturer Part Number 01464
This is a manufacturer sourced replacement seal. It is specially produced for use with Dynabrade sanders. This is one of the seals for the tip valve/inlet bushing. Over time seals tend to shrink and crack allowing for air leaks. At that time it should be replaced to maintain top performance. It is made out of rubber material and it is sold individually. Replacing this item you would need a wrench to replace this item.
Your Price
$68.19
In Stock
Dynabrade Drill Throttle Lever Assy., Safety L
PartSelect Number PS12023128
Manufacturer Part Number 01950
This part has been OEM sourced and is intended to be used with buffers, sanders, right angle reciprocating filers, and die grinders from Dynabrade. The metal lever assembly includes the safety lock and attaches to the body of the tool. This item is used to actuate the valve stem to allow compressed air into the tool to drive the rotor. The throttle lever assembly is sold as an individual replacement part.
Your Price
$17.45
In Stock
Dynabrade Drill Tip Valve
PartSelect Number PS10336578
Manufacturer Part Number 01472
This is a genuine OEM part. The Dynabrade tip valve is manufactured for use with orbital sanders, finishers and grinders. This metal and plastic valve often sits in the air inlet bushing, and is supported by a spring. The valve is sold individually, please see specific manual for additional repair information. A pair of pliers, wrench and a screwdriver may be necessary for installation.
Your Price
$6.41
In Stock
Dynabrade Drill Felt Silencer
PartSelect Number PS10336916
Manufacturer Part Number 04078
This felt silencer is supplied directly from the original equipment manufacturer. The Dynabrade part is compatible with a variety of different power tools and equipment. This item is fitted between the lock ring and the air control ring, minimizing the noise. The felt silencer is sold individually. For the repair, you may need a wrench and pliers.
Your Price
$46.32
In Stock
Dynabrade Drill Vanes (4/pkg.)
PartSelect Number PS10336548
Manufacturer Part Number 01185
This is an authentic component which is sourced directly from the original equipment manufacturer for use with Dynabrade equipment. This part is made of layered fabric and laminate and is used to spin the rotor. This part is designed to slowly wear down over time, to avoid damage to the cylinder. It is advisable to replace all the rotors at the same time for even wear. Keep in mind these high-quality blades are sold in a pack of four. Please make sure to check the owners manual and the appropriate diagrams of your model for the correct location and application of these parts.
Your Price
$13.72
In Stock
Dynabrade Drill Muffler Cap
PartSelect Number PS10338783
Manufacturer Part Number 56028
This is an authentic OEM component from Dynabrade. The plastic muffler cap is compatible with many sander devices. Fitted in the muffler assembly, the part secures the muffler insert. This part is made to help decrease the exhaust noise and capture any excess oil. The muffler cap is sold individually. A wrench and a screwdriver may be needed for the installation.
Your Price
$32.60
In Stock
Dynabrade Drill Bearing
PartSelect Number PS10336892
Manufacturer Part Number 02649
This authentic replacement part is designed for use with Dynabrade power tools. Ball bearings are used to reduce friction between rotating parts. It is one of the bearings for the rotor. The rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. Over time bearings may begin to wear out compromising tools functionality and eventually requiring a replacement. This part is made from durable metal and it is sold individually.
Your Price
$33.32
In Stock
Dynabrade Drill Bearing
PartSelect Number PS10336514
Manufacturer Part Number 01007
This is an original part assembled by the original manufacturer. It is compatible with various Dynabrade handheld power tools, such as grinders and finishers. Ball bearings are used to buffer between moving parts. They also serve to keep parts correctly positioned while assuring steady directional movement. Ball bearings need frequent replacement because of this high-wear role. This steel part is sold individually.
Dynabrade Drill Appliance Types
Popular Dynabrade Drill Models
Below are the most popular Dynabrade Drill models we have. Enter your model number in the search box to find your model.
- 53091 3/8" Pistol Grip Drill
- 53090 3/8" Pistol Grip Drill
- 53200 3,200 RPM Vacuun Drill
- 53048 1/4" Right Angle Drill
- 53047 1/4" Right Angle Drill
- 53080 7 Deg. 1/2" Drill
- 53070 400 RPM Drill
- 53075 400 RPM Lightweight Drill
- 53060 3/8" Pistol Grip Drill
- 53081 7 Deg. 1/2" Drill
- 53074 5,000 RPM Drill
- 53095 3/8" Pistol Grip Drill
- 53078 5,000 Lightweight Drill
- 53094 .7 Hp Pistol Grip Drill
- 53071 650 RPM Drill
- 53135 1/4" Central Vacuum Min-Angle Head Drill
- 53435 3,200 RPM Drill
- 52986 .4HP Pistol Grip 3/8" Drill
- 53037 .5HP Straight Line Drill
- 53076 650 RPM Lightweight Drill