EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

General Electric Washer Motors

Popular General Electric Washer Motors

This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. If you notice that your washing machine will not drain, there is a good chance that you will have to replace the drain pump. The drain pump is located inside the washing machine, near the bottom. To access the drain pump for this repair, you will need to remove the front panel. Before you begin this repair, be sure that the power source is disconnected and the water source is shut off.
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. If you notice that your washing machine will not drain, there is a good chance that you will have to replace the drain pump. The drain pump is located inside the washing machine, near the bottom. To access the drain pump for this repair, you will need to remove the front panel. Before you begin this repair, be sure that the power source is disconnected and the water source is shut off.
What this part fixes:
  • Burning smell
  • Draining Issues
  • Leaking
Installation Instructions
Gerald from Midlothian, VA
Washing Machine was not draining water from tub.
1. Drained the wash tub by taking the drain hose from the back of the washing machine and dropping it below the tub - water flowed out of hose a lot easier than trying to suck water out of tub using a pump (tried this on the first time I tried to fix washer). (Washing machine on 2nd floor of house and didn't want water running on floor)<br />2. Removed the 2 bolts holding the Pump/Motor assembly to the machine.
3. Removed both hose clamps on the Pump/Motor assembly and removed Pump.
4. Attached the new drain inlet hose to the pump and then to the tub with the original hose clamps.
5. Attached the drain hose to the pump and then plugged in the 2 wires for the pump.
6. Plugged in the washing machine and everything worked.

NOTES:
1. Hardest part was working with hose clamps (spring type clamps) in the tight space under the machine.
2. Easier to fix since I pulled machine apart a few days before - removing the clog in the pump/motor assembly only to get everything back together to find out that the motor was dead. Still well worth the time and effort due to not having to go out and buy a new Machine...
$218.03
In Stock
Installation Instructions
Darryl from FARR WEST, UT
Bad dryer motor
Replaced dryer motor which was a perfect fit thanks to your help. The process was helped by the internet videos available for the step by step procedure of taking the dryer apart and replacing the bad motor. I also was able to completely clean the inside of the dryer thoroughly, and reassemble it back together .
$121.40
In Stock
Enhance the performance of your washing machine with this top-notch 1/3 HP motor from GE. Specifically designed to effectively spin the basket and drive the agitator in agitation or tumbling mode, it ensures your washer is performing at its best. Remember to unplug your washer prior to installing this part to ensure safety. And don't forget to wear work gloves during installation to protect your hands. Settle only for genuine GE parts for optimal performance and longevity. Practicality and reliability make this GE Motor and Nut bundle an excellent choice for maintaining your appliance.
Enhance the performance of your washing machine with this top-notch 1/3 HP motor from GE. Specifically designed to effectively spin the basket and drive the agitator in agitation or tumbling mode, it ensures your washer is performing at its best. Remember to unplug your washer prior to installing this part to ensure safety. And don't forget to wear work gloves during installation to protect your hands. Settle only for genuine GE parts for optimal performance and longevity. Practicality and reliability make this GE Motor and Nut bundle an excellent choice for maintaining your appliance.
$110.55
In Stock
Original Equipment Manufacturer

MAKE THIS REPAIR A GUARANTEED WIN

OVER 2 MILLION PARTS TO ENSURE VICTORY

This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. This pump has sound isolation mounting washers and a filter.
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. This pump has sound isolation mounting washers and a filter.
What this part fixes:
  • Will not drain
Installation Instructions
Trent from Shreveport, LA
Washing machine would cease functioning at the spin cycle and would not drain.
Remove the front coverfrom the machine. This is done by removing the 3 screws at the bottom of the panel. The panel then drops down and pulls straight off. The pump is located on the front right wall of the of the machine. You will notice a 2-3 inch diamete threaded cap on the right side of the front wall of the machine. This is the front of the pump and access to the filter. Place a large bucket under this cap and slowly loosen the cap. All of the water remaining in the machine will begin to drain (this could be a lot of water. Do not remove the cap completely so that you can quickly stop the flow of water if needed). Once all water is drained from the appliance, Disconnect the two hoses from the pump using a pair of pliers to looses the presure clamps, sliding the clamps back an then pulling off the hoses (be careful of any remaining water in the hoses). Then remove the two screws from the rear base of the pump that secure it to the bottom floor panel of the washer. Slide the pump slightly to the rear to free it from the fittings on the front wall of the machine and the lift the pump up. At this point, firmly pull out the wiring harness plugged into the top right side of the pump. Install the new pump by plugging in the wiring harness and resecuring the pump. Plug in the machine and run on the rinse and spin cycle to test.
Use this with either a top load or front load washer. This pump has an horizontal mount.
Use this with either a top load or front load washer. This pump has an horizontal mount.
What this part fixes:
  • Leaking
  • Will not drain
Installation Instructions
Thomas from Walpole, MA
Pump Motor Failed
First, remove the 2 screws that hold the lower front cover in place, remove the cover and disconnect the plug and the ground wires from the pump. Next attach the washing machine drain hose to a wet vac, since even if the machine is empty, there will still be water in the outer tub and the pump. Suck the whole thing dry, remove the 2 bolts that hold the cover onto the pump, use a pliers to remove the 2 hose clamps, remove the hoses (no mess because of the vacuum). Remove the 2 screws that hold the pump to the base of the washer and remove the pump. Save the mounting bracket from the bottom of the pump. Orient the outlet on the new pump to match your old one if needed, instructions to do this are included with the new pump. Install the mounting bracket onto the new pump. Mount the pump to the washing machine base, reconnect the hoses, the cover and the wiring. Put the drain hose back into your drain. Run the machine, check for function and leaks. If all is well, replace the lower cover. Don't forget to tell your wife that the job was a whole lot harder than it looked.
$60.28
In Stock
Installation Instructions
Jose E from Mission, TX
Grinding noise LIke Gears that are not setting correctly.Disc
Disconnect power,turn off water,disconnect hose hot and cold. Disconnect drain hose careful water may drain out after you disconnect. Move washer to a place where you have enough room to work.Now lean washer to the floor on its back side Make sure to hold the lid from falling back I secure the lid with tape so it would not open. The washer should on its back side , you should see a gray wheel with a nut.Remove nut and pull the gray wheel off. you feel a magnetic pull, Once removed, you will see 3 screws remove stator now remove all screws holding the speed senors remove Mode shifter hold the Clutch because the spring is under it. Once you start it easy to replace. install new parts.
$179.19
In Stock
Boost your washer's functionality with this 1/2 HP drive motor and nut from renowned brand GE. It plays an essential role in your washing machine by spinning the spin basket and driving the agitator or spin basket during the agitation or tumbling program. For safety, always unplug your washer before beginning the installation of this part and don't forget to wear work gloves to safeguard your hands. Designed with durability and efficiency in mind, this robust 1/2 HP drive motor ensures your washer operates at optimal performance, significantly enhancing your laundry routine.
Boost your washer's functionality with this 1/2 HP drive motor and nut from renowned brand GE. It plays an essential role in your washing machine by spinning the spin basket and driving the agitator or spin basket during the agitation or tumbling program. For safety, always unplug your washer before beginning the installation of this part and don't forget to wear work gloves to safeguard your hands. Designed with durability and efficiency in mind, this robust 1/2 HP drive motor ensures your washer operates at optimal performance, significantly enhancing your laundry routine.

More General Electric Washer Parts

People often need to fix these common parts