General Electric Washer Panels
Find your part
Enter your model number or a part number and click "Search"
Popular General Electric Washer Panels
Your Price
$64.66
In Stock
Top Panel - White
PartSelect Number PS10061526
Manufacturer Part Number WH44X21834
Installation Instructions
Michael from FLORENCE, SC
Top had rusted out around the bleach dispenser and rusty water was getting in the clothes
Top panel was exactly what I needed and fit perfectly. To replace the top panel I first unplugged power. Removed control panel on top of machine. Removed front panel by placing a putty knife under front corners and pushing down on front panel. Removed two screws holding top panel to frame. Removed lid switch from top panel then removed lid from top panel. Lift up front of top panel and slide out of cabinet. Replaced new top panel in reverse order. The only thing I overlooked when ordering top panel was the plastic bumpers and rubber guides for the lid. Had to remove old parts from old top panel and use them. Overall job took about 45 minutes.
Read more...
Your Price
$167.97
In Stock
Your Price
$142.56
Special Order
Backsplash Panel - White
2. Using socket, remove three bolts on back of machine near top
3. Carefully slide backsplash to the right until tabs clear slots at bottom of backsplash
4. On back of backsplash, remove left two controls by pushing retainer tab inward and rotating counterclockwise
5. Remove right control by removing retaining screw with screwdriver
6. Reattach left controls to new backsplash by twisting clockwise until retaining tabs click into position
7. Reattach right control and secure with retaining screw
8. Slip backsplash tabs into holes and slide backsplash left into position
9. Replace three bolts on back using socket
10. Press left knobs back onto stems
11. Replace right knob with retainer clip Read more...
PartSelect Number PS1482474
Manufacturer Part Number WH42X10656
Installation Instructions
Jay from CLIFTON, NJ
Replace damaged backsplash MFR Part# WH42X10656
1. Remove left two control knobs by pulling straight out; remove right control knob by pulling retainer clip with needle nose pliers2. Using socket, remove three bolts on back of machine near top
3. Carefully slide backsplash to the right until tabs clear slots at bottom of backsplash
4. On back of backsplash, remove left two controls by pushing retainer tab inward and rotating counterclockwise
5. Remove right control by removing retaining screw with screwdriver
6. Reattach left controls to new backsplash by twisting clockwise until retaining tabs click into position
7. Reattach right control and secure with retaining screw
8. Slip backsplash tabs into holes and slide backsplash left into position
9. Replace three bolts on back using socket
10. Press left knobs back onto stems
11. Replace right knob with retainer clip Read more...
Your Price
$6.58
On Order
Your Price
$186.79
In Stock
Your Price
$226.63
Special Order
Your Price
$144.49
Special Order
Your Price
$352.95
In Stock
Your Price
$120.41
Special Order
Your Price
$294.32
In Stock
Related Parts
- All General Electric Washer parts
- General Electric Washer Agitators
- General Electric Washer Belts
- General Electric Washer Caps and Lids
- General Electric Washer Circuit Boards and Touch Pads
- General Electric Washer Dispensers
- General Electric Washer Drums and Tubs
- General Electric Washer Hardware
- General Electric Washer Hinges
- General Electric Washer Hoses and Tubes
- General Electric Washer Knobs
- General Electric Washer Latches
- General Electric Washer Motors
- General Electric Washer Power Cords
- General Electric Washer Pumps
- General Electric Washer Seals and Gaskets
- General Electric Washer Springs and Shock Absorbers
- General Electric Washer Switches
- General Electric Washer Timers
- General Electric Washer Valves
