My Orders
General Electric Washer Pumps
GET YOUR OFFICIAL General Electric PARTS TO ENSURE VICTORY
Popular General Electric Washer Pumps
This drain pump assembly is for washers. Drain pump assembly removes water from the washer during the drain portion of the cycle. The assembly may include multiple parts; refer to your parts diagram for a complete list of parts included.
This drain pump assembly is for washers. Drain pump assembly removes water from the washer during the drain portion of the cycle. The assembly may include multiple parts; refer to your parts diagram for a complete list of parts included.
Installation Instructions
Mike from NAPLES, FL
Washer ran fine but woudl not drain water - low humming noise
Drain all the water out of the tub with a shop vac
Remove rear drain hose and drained rest of water into a bucket
Remove small rear panel (bottom left hand corner) where the drain hose connects
Tipped washer up about 45 degrees to get underneath it - Supported it with a few paint cans
Remove internal drain hose/clamps ... Read more from pump - w/ pliers
Remove belt cover (gray plastic) with socket - 3 bolts
Remove wire assembly plug from socket
Remove old drain pump with socket - 3 bolts
Install new drain pump - 3 bolts - plug wire assembly into socket
Reinstall belt cover - 3 bolts
Reinstall hose to drain pump (note panel will be inside washer)
Feed drain hose panel through hole and reinstall - 1 nut
Re attached drain hose to exterior drain plug
You are done !
Remove rear drain hose and drained rest of water into a bucket
Remove small rear panel (bottom left hand corner) where the drain hose connects
Tipped washer up about 45 degrees to get underneath it - Supported it with a few paint cans
Remove internal drain hose/clamps ... Read more from pump - w/ pliers
Remove belt cover (gray plastic) with socket - 3 bolts
Remove wire assembly plug from socket
Remove old drain pump with socket - 3 bolts
Install new drain pump - 3 bolts - plug wire assembly into socket
Reinstall belt cover - 3 bolts
Reinstall hose to drain pump (note panel will be inside washer)
Feed drain hose panel through hole and reinstall - 1 nut
Re attached drain hose to exterior drain plug
You are done !
Read less
This is a drain pump, designed to work with your washing machine. It expels water from your washing machine during the draining cycle. The most common reason for needing to replace this drain pump is if your unit is not draining properly, is leaking, or if your pumps are not spinning. This model is gray in color and is encased in plastic. It about 9 inches high, almost 6 inches long, and 4 inches thick.
This is a drain pump, designed to work with your washing machine. It expels water from your washing machine during the draining cycle. The most common reason for needing to replace this drain pump is if your unit is not draining properly, is leaking, or if your pumps are not spinning. This model is gray in color and is encased in plastic. It about 9 inches high, almost 6 inches long, and 4 inches thick.
Installation Instructions
James from WILLOW STREET, PA
would not empty the water
read about the problem ordered the part and then installed
$61.55
In Stock
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. If you notice that your washing machine will not drain, there is a good chance that you will have to replace the drain pump. The drain pump is located inside the washing machine, near the bottom. To access the drain pump for this repair, you will need to remove the front panel. Before you begin this repair, be sure that the power source is disconnected and the water source is shut off.
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. If you notice that your washing machine will not drain, there is a good chance that you will have to replace the drain pump. The drain pump is located inside the washing machine, near the bottom. To access the drain pump for this repair, you will need to remove the front panel. Before you begin this repair, be sure that the power source is disconnected and the water source is shut off.
Installation Instructions
Gerald from Midlothian, VA
Washing Machine was not draining water from tub.
1. Drained the wash tub by taking the drain hose from the back of the washing machine and dropping it below the tub - water flowed out of hose a lot easier than trying to suck water out of tub using a pump (tried this on the first time I tried to fix washer). (Washing machine on 2nd floor of house and didn't want water running on floor)<
... Read more
br />2. Removed the 2 bolts holding the Pump/Motor assembly to the machine.
3. Removed both hose clamps on the Pump/Motor assembly and removed Pump.
4. Attached the new drain inlet hose to the pump and then to the tub with the original hose clamps.
5. Attached the drain hose to the pump and then plugged in the 2 wires for the pump.
6. Plugged in the washing machine and everything worked.
NOTES:
1. Hardest part was working with hose clamps (spring type clamps) in the tight space under the machine.
2. Easier to fix since I pulled machine apart a few days before - removing the clog in the pump/motor assembly only to get everything back together to find out that the motor was dead. Still well worth the time and effort due to not having to go out and buy a new Machine...
3. Removed both hose clamps on the Pump/Motor assembly and removed Pump.
4. Attached the new drain inlet hose to the pump and then to the tub with the original hose clamps.
5. Attached the drain hose to the pump and then plugged in the 2 wires for the pump.
6. Plugged in the washing machine and everything worked.
NOTES:
1. Hardest part was working with hose clamps (spring type clamps) in the tight space under the machine.
2. Easier to fix since I pulled machine apart a few days before - removing the clog in the pump/motor assembly only to get everything back together to find out that the motor was dead. Still well worth the time and effort due to not having to go out and buy a new Machine...
Read less
This drain pump access door is a durable component designed to cover the drain pump area on front-load washing machines, providing protection from dust and debris while allowing easy access for maintenance and repairs. Its precise fit helps keep internal parts safe and ensures a clean, finished look. Replacing a cracked, broken, or missing door restores proper protection and makes clearing debris or servicing the drain pump simple and convenient.
This drain pump access door is a durable component designed to cover the drain pump area on front-load washing machines, providing protection from dust and debris while allowing easy access for maintenance and repairs. Its precise fit helps keep internal parts safe and ensures a clean, finished look. Replacing a cracked, broken, or missing door restores proper protection and makes clearing debris or servicing the drain pump simple and convenient.
The drain pump removes water from the washer during the drain portion of the cycle.
The drain pump removes water from the washer during the drain portion of the cycle.
Installation Instructions
Jason from HARRIMAN, TN
Washer stopped during wash cycle and wouldn't open.
Removed three 7mm sheet metal screws from the bottom front panel.
The drain pump is in the front right.
Removed the manual drain screen to drain residual water from the system. A bucket was necessary to collect all the water.
Disconnected the inlet and outlet hose.
Disconnected the electric supply.
Removed two Phi ... Read more llips screws holding the pump to the bottom of the machine.
Slid the pump towards the rear to clear the support pegs and removed it from the front opening.
Installation is the reverse of those steps.
The drain pump is in the front right.
Removed the manual drain screen to drain residual water from the system. A bucket was necessary to collect all the water.
Disconnected the inlet and outlet hose.
Disconnected the electric supply.
Removed two Phi ... Read more llips screws holding the pump to the bottom of the machine.
Slid the pump towards the rear to clear the support pegs and removed it from the front opening.
Installation is the reverse of those steps.
Read less
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
This durable drain pump is designed to efficiently remove water from the washer tub during drain and spin cycles, ensuring smooth operation and preventing water buildup. Made from high-quality ABS plastic for impact and corrosion resistance, it provides long-lasting reliability. Common signs that your pump may need replacement include slow or incomplete draining, water pooling around the machine, or error codes related to drainage. The pump is typically located at the bottom of the washer for easy access. Installation is simple—always disconnect power, remove the old pump, and secure the new one in place.
This durable drain pump is designed to efficiently remove water from the washer tub during drain and spin cycles, ensuring smooth operation and preventing water buildup. Made from high-quality ABS plastic for impact and corrosion resistance, it provides long-lasting reliability. Common signs that your pump may need replacement include slow or incomplete draining, water pooling around the machine, or error codes related to drainage. The pump is typically located at the bottom of the washer for easy access. Installation is simple—always disconnect power, remove the old pump, and secure the new one in place.
Installation Instructions
Eric from HAMPTONVILLE, NC
Washer not draining
Ensure washer drum is empty of water before attempting repair. Disconnect the power to the appliance. Remove the front washer panel (a metal putty knife if needed to unlock the two upper tabs which releases the panel). Locate the existing drain pump at the bottom of the unit. Disconnect the two wires from the drain pump motor (one ora
... Read more
nge, one black/white). A pair of pliers and a gentle pull should do it. Using a small ratchet and socket, loosen and remove the two bolts that secure the drain pump to the bottom panel of the washer. Using a pair of pliers, squeeze the factory hose clamp on the large drain tube that connects the pump to the drum and remove the hose from the pump, being careful to capture any residual water from the drum. A towel is helpful to absorb the water. Repeat for the smaller discharge drain tube located on the side of the pump. Once both tubes are disconnected, remove the old pump. Install the new pump and reconnect everything in reverse order. Connect the small drain tube to the side of the pump. Connect the large drain tube from the drum. Ensure the clamps are properly secured. Insert and hand-tighten the two bolts that secure the pump to the bottom panel of the washer, making sure the bolts are snug but being careful not to overtighten. Reconnect the two wires to the motor. Restore power to the appliance. Run a quick wash cycle to ensure pump is working correctly and check for any water leaks. When satisfied, reinstall and secure the front washer panel.
Read less
Water left in the washer or clothes that remain very wet may point to a weak drain pump. A damaged impeller can also cause humming or drain error codes. Before replacing the pump, clean the filter and check the drain path for clogs. Match the new pump to the full appliance model and parts diagram. Unplug the washer, shut off the water, and prepare for spills. Reconnect each hose and wire correctly, tighten every clamp, and watch for leaks during a short test cycle.
Water left in the washer or clothes that remain very wet may point to a weak drain pump. A damaged impeller can also cause humming or drain error codes. Before replacing the pump, clean the filter and check the drain path for clogs. Match the new pump to the full appliance model and parts diagram. Unplug the washer, shut off the water, and prepare for spills. Reconnect each hose and wire correctly, tighten every clamp, and watch for leaks during a short test cycle.
This genuine recirculation pump assembly is designed to restore optimal cleaning performance in select GE washing machines. It works by drawing water from the bottom of the tub and redistributing it through the dispenser and other components, ensuring detergent is evenly dispersed and residue is minimized. Operating during both wash and spin cycles, the pump promotes consistent water movement, helping clothes come out cleaner while improving the efficiency of water and detergent use. If your washer is leaving clothes dirty, failing to fill or drain properly, making abnormal noises, or leaking near the pump area, these may be signs the pump needs replacement. Installation is straightforward for DIYers: unplug the washer, shut off the water supply, and wear gloves for safety. This OEM part is built for a precise fit and dependable performance, making it a confident solution for restoring your washer’s functionality.
This genuine recirculation pump assembly is designed to restore optimal cleaning performance in select GE washing machines. It works by drawing water from the bottom of the tub and redistributing it through the dispenser and other components, ensuring detergent is evenly dispersed and residue is minimized. Operating during both wash and spin cycles, the pump promotes consistent water movement, helping clothes come out cleaner while improving the efficiency of water and detergent use. If your washer is leaving clothes dirty, failing to fill or drain properly, making abnormal noises, or leaking near the pump area, these may be signs the pump needs replacement. Installation is straightforward for DIYers: unplug the washer, shut off the water supply, and wear gloves for safety. This OEM part is built for a precise fit and dependable performance, making it a confident solution for restoring your washer’s functionality.
Installation Instructions
Chris from BERRY, AL
Pump leaking
Tilt machine back to access pump on bottom of tub. Lay towel down to catch small amount of water. Use pair of pliers to remove clamp from recirculation pump hose. Remove 3 ten millimeter bolts from pump. Then use reverse procedure to install new pump.
This drain pump access door is designed to cover and protect the pump filter compartment on front-load washing machines, providing a clean, finished appearance while allowing convenient access for routine maintenance. Finished in a rich blue color, the door is made from durable, impact-resistant materials that withstand repeated opening, closing, and exposure to moisture during laundry use. It snaps securely into place using integrated mounting tabs, helping shield internal components from dirt, debris, and accidental contact. When the original access door becomes cracked, warped, or missing, the washing machine may be left exposed to damage or reduced efficiency. Installing a replacement restores proper coverage, maintains the appliance’s visual appearance, and ensures the pump filter area remains accessible for quick and easy cleaning.
This drain pump access door is designed to cover and protect the pump filter compartment on front-load washing machines, providing a clean, finished appearance while allowing convenient access for routine maintenance. Finished in a rich blue color, the door is made from durable, impact-resistant materials that withstand repeated opening, closing, and exposure to moisture during laundry use. It snaps securely into place using integrated mounting tabs, helping shield internal components from dirt, debris, and accidental contact. When the original access door becomes cracked, warped, or missing, the washing machine may be left exposed to damage or reduced efficiency. Installing a replacement restores proper coverage, maintains the appliance’s visual appearance, and ensures the pump filter area remains accessible for quick and easy cleaning.
