General Electric Washer Hinges

General Electric Appliance Parts
Shop By Part Type

Popular General Electric Washer Hinges

Your Price
$74.34
  On Order
Door Hinge
PartSelect Number PS6447711
Manufacturer Part Number WH01X10653
Your Price
$6.25
  In Stock
Lid Bumper
★★★★★
★★★★★
(1)
PartSelect Number PS271095
Manufacturer Part Number WH1X2722
This bumper is sold individually. The bumper is located under the washer lid.
Fixes these symptoms
Installation Instructions
Guy from New Palestine, IN
I Placed A Heat Gun In The Freezer Section To Defrost The Coils And Did Not Return In Time. The Heat From The Heat Gun Rose Upward And Melted All Of The Soft Plastic Parts. The Good News Was That The 16 Parts Were Not Expensive But The One Main Part That Was Needed To Put It All Back Together Took 3
I replaced all of the plastic parts as well as the heat coil that is mounted at the bottom of the coils that keeps the coils from freezing up. If I had not melted the plastic parts the coil could have been replaced in 2 days, 1 day to receive the part and the next to do the work. This is the second time I have had to replace this heater. Read more...
Your Price
$6.24
  In Stock
Door Hinge
★★★★★
★★★★★
(1)
PartSelect Number PS8756812
Manufacturer Part Number WE1M1033
Screws NOT included.
Fixes these symptoms
Your Price
$6.24
  In Stock
Hinge Bushing
★★★★★
★★★★★
(1)
PartSelect Number PS271111
Manufacturer Part Number WH1X2741
Installation Instructions
Michael from Ballwin, MO
unit would not agitate or spin
I checked the motor,it was bad I was pulling to 20 amps too much. The washer was still not working and the motor was bad so I checked the lid switch for continuity. The switch was a magnet type so with the lid down you should have continuity. In other words, a closed circuit. When the lid is opened, you should have a open circuit, Which would show no continuity. An open circuit means a break in the circuit. To change hinge bushings, raise lid, remove the screws on the outside of the lid, remove hinge, remove lid, insert new hinge bushings, place hinge through lid into bushings, and then put the screws back into the lid. If you followed these steps you should be done. Read more...
Your Price
$7.79
  In Stock
Short Wire Form Hinge
PartSelect Number PS271110
Manufacturer Part Number WH1X2740
When the lid is being closed, the angle of this hinge applies pressure to the lid lever.
Installation Instructions
Jeff from Blacklick, OH
Needed to replace a rusted washer lid
All the parts were delivered in 3 days, every part fit perfectly.

The on line parts service person was very helpful.

We saved hundreds of dollars!

Highly recommend.
Read more...
Your Price
$14.01
  In Stock
Hinge Bushing
★★★★★
★★★★★
(1)
PartSelect Number PS268416
Manufacturer Part Number WH01X10025
Fixes these symptoms
Installation Instructions
Thomas from Baltimore, MD
knob asm control/ bushing hing
First remove clip with srewdriver and pulled the knob off, then replace with new knob and replaced the clip, the next thing I removed two screws with a philps screwdriver and remove the the bracket then I slip the bushing on the bracket took a little while to figure how to replace it in the process of replacing the two screws I broke the bracket which I will order later, the only real problem I had was I did not have to order the timer knob clip because it came with the knob the picture did not imform me that it was there other then that it was easy Read more...
Your Price
$8.46
  In Stock
Wire Form Hinge - Long
PartSelect Number PS271113
Manufacturer Part Number WH1X2743
Installation Instructions
Jeff from Blacklick, OH
Needed to replace a rusted washer lid
All the parts were delivered in 3 days, every part fit perfectly.

The on line parts service person was very helpful.

We saved hundreds of dollars!

Highly recommend.
Read more...
Your Price
$75.51
  In Stock
Door Hinge
PartSelect Number PS8756998
Manufacturer Part Number WH01X20169
Your Price
$55.17
  On Order
HINGE
PartSelect Number PS11721789
Manufacturer Part Number WH01X20901
Installation Instructions
Suzanne from Mc Cayesville, GA
Broken hinge
Unplug the machine. Remove the door by taking out the 4 screws holding the hinge cover. Then remove the three screws that attach the hinge to the door. You may need to remove the hinge pin (mine fell off as the top of the hinge was broken) Set aside the door. Remove the spring clamp that holds the rubber boot to the washer front. Use needle nose pliers to pull the spring away from the boot and use a screw driver to ply it away from the boot around the ring. Gently lift away the left side of the boot to reach the hinge. Remove the four screws that hold the hinge to the washer frame. Reach in and remove the broken hinge.
Insert the new hinge and replace the 4 screws. Replace the rubber boot over the lip of the washer frame. Replace the spring clamp around the rubber boot being careful that the boot seats evenly all the way around the washer door opening. This was the hardest part! Reattach the door. to the hinge and replace the hinge plate over the hinge.
Read more...
Your Price
$6.68
  On Order
HINGE DOOR PLATE
PartSelect Number PS1482315
Manufacturer Part Number WH01X10340

Related Parts