This assembly comes with two shocks, four nuts, one leveling leg pin and instructions. These shock absorbers keep the washer from vigorous shaking during it's cycles.
This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
7 questions answered by our experts.
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Katie
January 24, 2020
My washing machine will advance by hand, but not automatcally.
For model number WSXH208A1WW
Hello, Thank you for your question. Typically the part you need to replace when the machine will not advance is the timer, that is -PartSelect Number: PS269881. We hope this helps.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Ted
February 10, 2020
Have oil spots on cloths after wash. Also makes loud noise on the spin cycle
For model number WSXH208A1WW
Hello and thank you for writing.
When the rubber breaks down, oil and grease can make their way out of the outer tub assembly PS273277. If the watertight seals that keep the engine compartment dry fail, then that oil and grease can enter the washing machine's drum during a wash cycle. Oil doesn't mix with water, so that's why you see spots on your clean clothes. It would make this noise if the bearing of the tub has gone defective which seems to be the case here. The bearing is included in the assembly. We hope this helps. Please contact us anytime if you require further assistance.
Hello Richard, thank you for writing. We have researched the model you have provided and have found the part you are looking for is the Door Lock Assembly PartSelect Number PS12343346. Good luck with your repair.
Hello Connie, thank you for your inquiry. The bearing and seal is not available separately. The Rear Outer Tub with Bearing and Shaft Seal is part PS273277. We hope this information will help you.
Hi Bob,
Thank you for your question. The washer measures 25.75 inches deep by 36.0 inches high by 26.75 inches wide and has a capacity of 3.1 cubic feet. If you have any questions, please let us know. We are open 7 days a week. We look forward to hearing from you!
Disconected power & hoses. Removed 4 screws from two tabs at rear of top. Slid top fwd & up to remove. Removed two screws from lower front panel and removed panel. Removed back cover screws and back cover. Placed sling arround tub & lifted with 2"X4" on strap placing additional wood under sling supported by edges of machine. Removed one scred and loosened mother that held spring hook in place. removed broken end and remainder of spring. hooked spring in hole in tub and raised spring upper hook on to support , re installed retainer. Went to lower side and removed plastic push bolts, by slipping a 1/2 " deep socker over front end and pulling from back with plirers.allign the holes in the new shock with the mount holes and nock them in place. remove sling from arround tub and re assemble all removed parts.
This is the second time in the same 7 year old appliance. Remove the front bottom cover by removing 2 screws. Then remove the 2 screws holding the pump down. Then unclip the electrical wire from the pump and remove both hoses from the pump by squeezing the spring clamps with a pliers. Have a pan to collect the water that will drain from the lines. Take the new pump and install it in reverse order from above.
after pulling pins and installing new shocks, the washer still made loud ,disturbing sounds during use. Did some more investigating, turns out the inner bearings on the drum are bad. Apparently a problem with this model. Probably why the original shocks broke in the first place.
The Fix App makes it easy to manage all your stuff in one place. Just snap a photo and we'll find and store your user manuals, receipts, and product information in one easy-to-find place!
"Like magic. I took a picture of the model number on my refrigerator, and the app identified it right away … Very convenient. I'm impressed." ★★★★★ - Clever Jeff
