The tub dampening straps support the wash tub and reduce vibration by keeping the tub at the center of the cabinet. If your washer shakes and moves, or is making a loud banging noise during the wash cycle, the washing machine tub could be off-balance, meaning one or more of these straps may be loose, or broken. Other symptoms include: the...Read more washer leaking, not agitating, or pumping but not spinning. These straps are sold individually. However, we recommend that you replace all 4 straps at the same time. It is also recommended that you check the tub for cracks where these straps mount.
This set (Knob and Clip Assembly, Control Knob, Dryer Control Knob) allows you to replace the knob on your timer if it is damaged or missing. The plastic knob can break around its shaft, or the retainer clip inside the knob can fall out and no longer stay securely on the control shaft. If your knob no longer stays in place, it’s time to p...Read morelace it. The knob is attached to the d-shaped shaft of the control mechanism. This model has a 2 inch diameter, 1-1/14 inch depth, and comes in white plastic.
This is a replacement timer knob for your washing machine. To complete this repair you will need a pair of needle nose pliers. Turn off power to the washer before you start. Pull off the timer knob and use your pliers to remove the retaining clip. The new knob will already have a clip in place. Line up the knob opening with the shaft and slide it on.
This clip ensures that the knob is securely fastened to the control shaft, allowing you to properly select the correct time and setting for your dryer. If your dryer will not start or shut off, the timer will not advance, or the dryer shuts off too soon, the issue may be the control knob itself. This clip is sold individually. Although th...Read moreis part fits with some different brands, be sure to check the list of brands below to make sure it fits with your dryer unit. Refer to the manual provided by the manufacturer for further installation instructions.
The drain hose is black in color and made of flexible material. This is a part for your top-load washer. The hose measures 57 inches long. This part moves the water out of the washer and into the drain. If this parts cracks or becomes damaged it will leak during the drain cycle of your wash and you may find water on the floor. To access t...Read morehe hose, you will need to move the washer away from the wall to get to the back of the appliance. There will be two screws holding it in place that will need to be removed.
This is a dual-action agitator for a washer. It is an OEM replacement part that is sourced from the manufacturer. The agitator tosses your clothes to clean them efficiently. This plastic dual-action agitator is white in color. It is approximately 18 inches tall with a base diameter of about 12 1/4 inches. No tools are required for this re...Read morepair. Your agitator has eight tabs that fasten on the drive block of your washer, which is driven by the transmission. This part does not include the agitator coupling kit, which is frequently purchased at the same time as the agitator.
This timer dial with compression ring shows you which part of the cycle your washer is in. It is white in color and can be found mounted on the timer shaft. You may need to replace this part if your old timer dial is cracked or damaged, or if it is not indicating correctly. This part is sold separately from the timer knob, and the timer knob clip.
The main tub seal is located between the transmission and the outer tub. Its the primary water seal in the outer tub for the transmission-shaft. If your washer is leaking during the fill cycle, or at agitation time, your tub seal may need to be replaced. You can check if the tub seal needs to be replaced by watching that area during an ac...Read moretual fill cycle. Take off the front panel, or if it is a front-loading washer, the rear panel. Without touching the washing machine, observe the place where the shaft of the transmission comes into the tub and the weep holes at the housing of the rear bearing. If there is water leaking, the tub seal is at fault.
NOTE: This seal is difficult to replace and should probably be installed by a qualified technician.
This is a tub bearing and it is meant to work in conjunction with your washing machine. The purpose of this part is to aid in keeping the inner tub of your washing machine spinning smoothly during a wash cycle. The most common reasons for needing to change your tub bearing is if your appliance is noisy or shaking/moving during the wash cy...Read morecle, another common symptom is leaking water. This part is sold individually and measures to have an inner diameter of roughly 1 inch, and an outer diameter of roughly 2 inches.
This split ring is supplied by the original equipment manufacturer, and it is designed to secure the tub bearing in washing machines. It is a circular metal ring, with an outer diameter of 2 inches. The ring has a split or gap, which allows it to expand and contract for easy installation and removal. It is typically located on the inner s...Read moreide of the washing machine outer tub, where it provides stability and prevents the washer from excessively shaking during use. It is normal for the split ring to become worn, corroded, or damaged due to age, exposure to moisture, and excessive stress. A faulty split ring will lead to a noisy, unstable washer and eventually cause the tub assembly to fall out of alignment. Remove the washer panels to access the outer tub and split ring. Carefully detach the damaged split ring from the tub and position the new split ring in its place. Ensure that it is properly aligned and securely fastened before reattaching the panels.
This tub bearing goes in your washing machine. You will find it on the bottom of the outer tub, where the transmission goes through the tub. If you hear metal on metal when the washer is spinning, you may need to replace the tub bearing. This bearing is made of metal, and is approximately 3 inches wide and 2 inches tall.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
2
3
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Davis - For model number GTWN2800D1WW
December 5, 2019
Seems to agitate very slowly is this normal?
Hello Davis, thank you for writing. Replacing the Agitator Coupling, part number PS1482517 for your model washer should improve this. Good luck with your repair!
4 peoplefound this instruction helpful.
Was this helpful?
Thank you for voting!
Eric - For model number GTWN2800D1WW
March 9, 2023
Does this machine have a filter for the drain?
Hello Eric, thank you for contacting us. According to our research, your model does not contain any filters for the drain. We hope this helps!
4 peoplefound this instruction helpful.
Was this helpful?
Thank you for voting!
Mike - For model number GTWN2800D1WW
September 2, 2022
Clothes are still wet after spin cycle. Also little water puddles in the Tub. Have to run spin cycle twice. What could be causing this?
Hi Mike, thank you for contacting us. Most of the times, for a washer that spins but still turns out wet clothing, this is a drain hose problem. It could be clogged, kinked, or positioned incorrectly. You will also need to clean the drain filter, located behind a small access panel at the bottom of the washer. Open the panel, take out the filter, and remove any accumulated debris. If the filter has checked out, the next thing to do is to check the drain pump. You can access the drain pump by removing the drain hose and the back panel of your washer. Check for debris, which should be obvious to see. If you find no blockages, you will need to test the drain pump to see if it is actually working properly. Test the pump for continuity using a multimeter. A reading other than 5-10 ohms means the pump has malfunctioned and needs replacement. You will also need to check the belt. Over time, the belt that helps spin the washer drum can become stretched, which will affect how fast the washer can spin. If the belt is stretched out, it can slide around during the cycle and will not allow the washer to reach the speeds that it needs to in order to remove all excess water. Please contact us anytime if you require further assistance.
Can the agitator be replaced with an impeller. The existing agitator is ruining my clothes.
Hi Verlene,
Thank you for your question. If the agitator in your washer is ruining you clothes, you may be overloading it. If you are overloading the washer, this may cause your clothes to become damaged during the wash cycle. Overloading the washer places a lot of pressure on the bearings, drum and the motor, causing these parts to wear out and become damaged over time. Overloading the washer may also push articles of clothing into the door or under the agitator which would cause them to pull when the washer is running. Try washing the clothes in smaller loads. Also, check the labels on your clothes to see how they should be washed and make sure you are using the correct wash cycle for the clothes that you are washing. Clothes that are considered delicate should be washed by hand. We hope this helps. Thank you and have a great day.
1 personfound this instruction helpful.
Was this helpful?
Thank you for voting!
Janet - For model number GTWN2800D1WW
February 23, 2020
Why washer does not spin and drain sometime
Hello Janet, Thank you for the question. We suggest checking the Lid Switch, PartSelect Number PS1482372 to see if the wiring is loose or the switch is damaged. If damaged, it will not allow the Spin and drain cycle to start. We hope this helps.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Control knob teeth were worn
510 of 517 peoplefound this instruction helpful.
Charles from Dallas, GA
Really Easy
Less than 15 mins
Pliers
I spoke to a very nice young ladie who took my order and I received my order within two days. I pull the clasp off of the old knob and replace the knob and the clasp with the new part and it now works great. Thank you for helping me find the part I needed.
Was this helpful?
Thank you for voting!
The original Knob just fell apart
380 of 390 peoplefound this instruction helpful.
Irina from Englewood, NJ
Really Easy
Less than 15 mins
The repair was so easy when I got the part, I did it myself without any help in 5 seconds!
Was this helpful?
Thank you for voting!
washing machine would not go through all cycles or agitate
230 of 294 peoplefound this instruction helpful.
Brian from Millerplace, NY
Easy
15 - 30 mins
After removing frt panel which prys off I checked for anything obvious like a loose belt. Then I jiggled the magnet switch located on the inside of the loading cover. I saw the machine start agitating the it stopped again when I stopped touching it. I ordered the new part and spliced it in with the wire crip tool. Now the machine is A ok.
My Orders
