Frigidaire Washer Parts
Find your part
Enter your model number or a part number and click "Search"
Popular Frigidaire Washer Parts
Your Price
$24.08
Drive V-Belt
PartSelect Number PS1146950
Manufacturer Part Number 134511600
This rubber V-style drive belt slips on the motor pulley to bring the basket to the required speed. If you notice a burning rubber smell or grinding noises coming from your washer, your washer does not start, drain, spin properly (will not spin/spins slowly/will not agitate properly), or if your washer shakes or moves during the cycle; check your drive belt for signs of wear and tear. Replace the drive belt if you notice that the belt looks damaged. This OEM part is approximately 35 inches in length, and sold individually.
Fixes these symptoms
- Burning smell
- Noisy
- Spins slowly
- See more...
Installation Instructions
rodney from fairfield bay, AR
replace broken drive belt
carefully pry up on front washer top to release plastic keeper pins,remove 2 phillips screws from beneath lower front washer panel,slightly lift upward on panel to release.remove old broken belt,push new belt beneath large tub pulley,put belt on small motor pulley,push back belt tension /idler arm,start belt on large tub pulley,turn tub pulley by hand to run belt on,release tension on idler arm.replace front panel and lower top.WALAAH!!!! you are done.
Read more...
Your Price
$13.62
Door Strike
PartSelect Number PS890617
Manufacturer Part Number 131763310
The door strike on your washing machine allows your washer door to lock properly, and operate efficiently. If you notice that your washer door will not open or close, leaks or the washer will not start or spin, you may need to replace the door strike. This part is for front load washers and is white in color. The part is made of plastic and is roughly 2 inches in length. To complete this repair, you will only need a Phillips screwdriver. Most of our customers found this repair to be easy and took less than 15 minutes to complete it. This part is sold individually, not as a part of a kit, and is a genuine part approved by the original manufacturer.
Fixes these symptoms
- Door latch failure
- Door won’t close
- Leaking
- See more...
Installation Instructions
Joy from Columbia, MO
Broken Door Catch
This was one of the simpliest repairs I have ever done taking less than 5 minutes to complete. On the inner door I removed the two screws that hold the plastic catch in place. I then removed the broken catch and put the new catch in place. Finally I replaced the two screws that hold the catch in place and it was done.
Read more...
Your Price
$116.26
Front Load Washer Door Lock and Switch Assembly
2. Unscrew 2 nuts holding top in place in rear of unit using phillips head screwdriver.
3.Slide top back and remove.
4. Open door of washer and unscrew 2 screws holding in door lock unit.
5.Pull out unit from the top and install new unit reconnecting the 3 wire connections. Read more...
PartSelect Number PS12364048
Manufacturer Part Number 131763256
This door lock and switch assembly is manufactured to lock the door on your front load washer to prevent it from opening while it is running. You may need to replace the door lock and switch if the door does not open or lock. Your washer will not start if the door does not lock. This part is also known as a washing machine door lock assembly. As per the manufacturer, some models require a new wire harness and a door strike for this door lock assembly to work on the appliance. The original style lock would require the door lock kit.
Fixes these symptoms
- Leaking
- Lid or door won’t close
- Spins slowly
- See more...
Installation Instructions
DOUG from KING FERRY, NY
Door on washer wouldn't lock or start
1. Unplug unit.2. Unscrew 2 nuts holding top in place in rear of unit using phillips head screwdriver.
3.Slide top back and remove.
4. Open door of washer and unscrew 2 screws holding in door lock unit.
5.Pull out unit from the top and install new unit reconnecting the 3 wire connections. Read more...
Your Price
$141.86
Drain Pump - 120V 60 Hz.
PartSelect Number PS7783938
Manufacturer Part Number 137221600
This is a 120 volt, 60 hertz drain pump that is manufactured to remove water from the tub of your washer once your clothes are washed. This part is the pump and motor assembly, which includes a red flapper to prevent drain backflow. You will need to remove the front panel of your washer to access the drain pump. The tools you will need for the repair are a Phillips screw driver, a putty knife, a pair of slip joint pliers, and a 5/16 nut driver. Be sure to disconnect the water supply from your washer before doing the repair. The metal edges on the appliance are sharp, so use work gloves to safely complete the repair.
Fixes these symptoms
- Leaking
- Not draining
- Will not drain
- See more...
Installation Instructions
kenneth from willard, OH
would't spin all water out or rinse out clothes
uplugged washer took front off washer 2 screws pryed up top pump was mounted with 2 screws and 2 wires took off found change in pump and the fins to pump worn off ordered part off line the wait for part was longer than the amount of time to fix problem and cost of part saved me about $25-35 if I was to buy local worth wait save money and fix problem washes like new spins and drains all water from tub.
Read more...
Your Price
$19.48
Door Striker
PartSelect Number PS2378364
Manufacturer Part Number 131763302
This is a door striker, it is gray in color and is a part found on your washer. The purpose of the striker is to keep your washer door closed for usage. This piece will attach to your appliance lid and will activate the door switch when your lid is closed. The most common reasons for needing to replace this part are if your lid will not consistently open or close, and your washer will not consistently start. The only tool you will need to complete this installation is a Phillips screwdriver.
Fixes these symptoms
- Door won’t close
- Lid or door won’t close
- Will Not Start
- See more...
Installation Instructions
Paul from Grinnell, IA
Door Striker broke which was a result of the hinge problem.
Removed the screws holding the door. (One was stuck a little so used an air drill with Phillips head to get the torque needed but someone with a strong grip could have done it as it came out very easily). I removed most of the screws holding the front to back of door to exchange the hinge. There was a problem with the old hinge slopping around and not allowing the door to align properly when shutting it. The new hinge works better. See note*** below on doorframe. I pretty much was able to get the door back together and make it work. I then exchanged the door striker with no problem. It has a built in key so you cannot attach it incorrectly. The next thing was to just reattach the door to the machine and it worked right off the bat. ------------- *** Unfortunately, there were two screw mounts in the Outer Door Frame - Chrome Part Number: PS3495258 that were broken. This doorframe is listed as a $200+ chrome part whereas it is actually a plastic material that is extremely over priced for what it is. Like I mentioned two of the screw mounts had broken off so those screws are just "decoration" now. (These are screws that basically hold the back cover to the front cover). If this becomes a problem, I will simply modify what I have and make the screws fit before I spend $200+ on that part. (It looks like this could be drilled out and a long screw and nut run through to make it work. TELL THE WASHER OPERATOR… just be careful opening and closing the unit (don't slam the door but carefully close it) and it should work a lot longer. I might investigate the make up of a washer the next time I buy one … but the chrome vs. plastic is a hard one to spot. I hope this helps.
Read more...
Your Price
$45.08
Water Inlet Valve
PartSelect Number PS815509
Manufacturer Part Number 134190200
The water inlet valve has two ports for water to enter and controls the flow of water into a washing machine. Hot, cold, and warm water can easily enter the washer this way. If the water inlet valve is in any way damaged or defective, it may be slow to fill or even leak. Before beginning this replacement, make sure to unplug the washer from the power range or shut off the house circuit breaker. Remember to wear gloves for safety. Refer to the installation instructions and the diagram provided by the manufacturer for best results and accuracy.
Fixes these symptoms
- Leaking
- No hot or cold water
- See more...
Installation Instructions
alvaro from east hampton, NY
Washer Continued To Fill To Point Of Overflow
First I removed the top panel held by four screws at rear of panel, pulling the panel foward and up. Then disconnected the power and water connections. Then I removed the two screws holding the flow valve to the washer rear panel,pulled the valve foward ,removed the two electric connectors, pinched the water clamp with pliers and removed the water connection to the valve. Then replaced with the new valve followed the above steps in reverse order, finishing up by re placing the water connections and power. Then checked fo proper replacenent and leaks before replacing top panel.
Read more...
Your Price
$14.83
Upper Spin Bearing Washer
2) removed the 2 phillips screws at the bottom of the front panel then removed front panel, you need enough clearance by the floor, this is tricky because you have to lean washer back and push down on the front panel.
3) removed the agitator from the washer
4) lifted top of washer and leaned back against the wall and removed the splash tub cover one clip at a time with a flat screw driver.
5) removed the trunion, this is difficult and will take some time due to the corrosion from many years of use use a hammer (3Lb short handle) and tap one side then the other. You will need to rock it back and forth awhile.
6) lift the basket out of splash tub
7) I removed the hose for water level and removed the 3 bolts that hold the splash tub to the three base mounts (support arms).
8) remove the splash tub
9)change the plastic washer that is between the splash tub and the transmission in the bottom of the splash tub
10) change the bearing(metal sleeve) on the bottom of splash tub and lightly grease w/ a thin film of teflon grease
11) install splash tub and install the 3 bolts along w/ the water level tube
12) install the larger seal (w/ spring in it) and push into the splash tub firmly
13) use some tub and faucet silicone grease on the smaller seal because you don't want to damage this main seal, install the main seal (sits on top of the larger one that's in the tub already) be careful when getting to flat part of the shaft when installing ( spin around the shaft as you pass this point) it will keep the seal from coming out.
14) install trunion (sits down on top of the seal) you will feel the tension of the spring when bolting the trunion back into place.
15) install basket and bolt it to the trunion (I installed a new filter on the bottom of the basket and required some special glue, ask for "3M" GMGA600 adhesive.
16) installed splash tub cover, agitator and front cover.
Washer works great and is quieter than it was new. Read more...
PartSelect Number PS473382
Manufacturer Part Number 5308002401
The upper spin bearing for a washer can solve many issues such as loud and odd noises, or leaking water. Replacing the spin bearing could solve these issues. The tools needed for this replacement are screwdrivers, a socket set, and a putty knife. To repair, first lift the top of the washer and remove the screws at the bottom of the front panel to pull away. Next, pull off the dispenser cover, cup, and agitator. Detach switch tube from the tub cover and remove tub cover, then use the 1/2 inch socket to remove the trunnion bolts and pull out inner tub. For the rest of the installation instructions, refer to the diagram provided by the manufacturer. Remember to unplug the appliance from the power source as a safety precaution.
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
Patrick from Humble, TX
Noisy spin cycle
1) Unplugged washer and disconnected the hot and cold hoses.2) removed the 2 phillips screws at the bottom of the front panel then removed front panel, you need enough clearance by the floor, this is tricky because you have to lean washer back and push down on the front panel.
3) removed the agitator from the washer
4) lifted top of washer and leaned back against the wall and removed the splash tub cover one clip at a time with a flat screw driver.
5) removed the trunion, this is difficult and will take some time due to the corrosion from many years of use use a hammer (3Lb short handle) and tap one side then the other. You will need to rock it back and forth awhile.
6) lift the basket out of splash tub
7) I removed the hose for water level and removed the 3 bolts that hold the splash tub to the three base mounts (support arms).
8) remove the splash tub
9)change the plastic washer that is between the splash tub and the transmission in the bottom of the splash tub
10) change the bearing(metal sleeve) on the bottom of splash tub and lightly grease w/ a thin film of teflon grease
11) install splash tub and install the 3 bolts along w/ the water level tube
12) install the larger seal (w/ spring in it) and push into the splash tub firmly
13) use some tub and faucet silicone grease on the smaller seal because you don't want to damage this main seal, install the main seal (sits on top of the larger one that's in the tub already) be careful when getting to flat part of the shaft when installing ( spin around the shaft as you pass this point) it will keep the seal from coming out.
14) install trunion (sits down on top of the seal) you will feel the tension of the spring when bolting the trunion back into place.
15) install basket and bolt it to the trunion (I installed a new filter on the bottom of the basket and required some special glue, ask for "3M" GMGA600 adhesive.
16) installed splash tub cover, agitator and front cover.
Washer works great and is quieter than it was new. Read more...
Your Price
$57.71
Shock Absorber Kit
PartSelect Number PS3508101
Manufacturer Part Number 5304485917
This shock absorber kit is an authentic OEM part that is sourced directly from the manufacturer. The kit includes two dual-stage shock absorbers, one spare shock mounting pin, and four locking nuts. These shock absorbers keep your front-load washer from shaking vigorously by absorbing and reducing vibrations from the wash and spin cycles of your appliance. This kit comes with two shock absorbers because it is recommended to replace both at the same time, as they wear at the same rate. To access your washer shock absorbers, simply remove the lower access panel after disconnecting the power to the appliance.
Fixes these symptoms
- Leaking
- Noisy
- Spins slowly
- See more...
Installation Instructions
Douglas from Medical Lake, WA
Both vibration shock absorbers broken
removed 2 screws and removed top access cover. removed 2 screws and removed front access cover. removed 4 retaining pins (one with nammer and punch because it was stuck) connected lower ends of new shocks with plastic pins, extended each shock to slip fit and connected upper ends to wash tub mounts. Reinstalled panels. I wish I could say that it all went well from there but......when the shocks broke, apparently the hit the motor took was enough to cause an electronic failure of the speed cycle control chip. Now Im waiting for that part.
Read more...
Your Price
$102.29
Door Hinge with Bushings
PartSelect Number PS1152380
Manufacturer Part Number 134550800
This is a door hinge with bushings and works in conjunction with your washer. The purpose of this part is to attach to the outside of the front door panel to help with the lid opening and closing properly. The hinge will fasten the front panel of the washing cabinet to the lid of the washer. This piece is roughly 9 inches long, almost 3 inches high, and roughly 2.5 inches wide. The reason for needing to replace this part is if your lid/door will not open or close properly, which may lead to leaking.
Fixes these symptoms
- Leaking
- Lid or door won’t close
- Will Not Start
- See more...
Installation Instructions
Paul from Grinnell, IA
Door Striker broke which was a result of the hinge problem.
Removed the screws holding the door. (One was stuck a little so used an air drill with Phillips head to get the torque needed but someone with a strong grip could have done it as it came out very easily). I removed most of the screws holding the front to back of door to exchange the hinge. There was a problem with the old hinge slopping around and not allowing the door to align properly when shutting it. The new hinge works better. See note*** below on doorframe. I pretty much was able to get the door back together and make it work. I then exchanged the door striker with no problem. It has a built in key so you cannot attach it incorrectly. The next thing was to just reattach the door to the machine and it worked right off the bat. ------------- *** Unfortunately, there were two screw mounts in the Outer Door Frame - Chrome Part Number: PS3495258 that were broken. This doorframe is listed as a $200+ chrome part whereas it is actually a plastic material that is extremely over priced for what it is. Like I mentioned two of the screw mounts had broken off so those screws are just "decoration" now. (These are screws that basically hold the back cover to the front cover). If this becomes a problem, I will simply modify what I have and make the screws fit before I spend $200+ on that part. (It looks like this could be drilled out and a long screw and nut run through to make it work. TELL THE WASHER OPERATOR… just be careful opening and closing the unit (don't slam the door but carefully close it) and it should work a lot longer. I might investigate the make up of a washer the next time I buy one … but the chrome vs. plastic is a hard one to spot. I hope this helps.
Read more...
Your Price
$69.92
Tub Seal Assembly
2. Using my fingers, I released the tabs that connect the tub cover to the tub. It took some effort to remove the cap("Mechanism") over the bolt connecting the agitator to the agitator drive block because I didn't want to break the tab. Once removed, I removed the bolt and the agitator. I then removed the two bolts that clamp the Trunnion to the agitator shaft.
3. It took a little more effort to remove the tub because of corrosion, however, by rocking the tub back and forth I was able to work it free and remove it. I then removed the bolts connecting the Trunnion to the tub. It took a hammer to remove the Trunnion from the tub, once again because of corrosion.
4. After removing the tub, the seal assembly was next and it was easy to remove. I cleaned the agitator shaft with steel wool before beginning the reassembly to remove the corrosion. Before installing the new seal, I lubricated the agitator shaft and the inside of the seal with a silicone grease that is normally used for water faucets. The seal installed easily although care was required to insure that the seal did not twist out of place when sliding it down the agitator shaft.
5. The rest of the reassembly went easily. Since my old filter on the bottom of the tub was clogged, I replaced it with a new one. It took a little time to get every tab on the filter aligned properly so that it could be rotated into place, but it went easily. Everything else reassembled with no problems.
6. It took considerable time to figure out how to replace the drive belt idler arm assembly because I could not figure out how to remove the pin that the idler arm pivots on. I finally reviewed the parts list on-line again and determined that there is a small C-clip that holds it together. Once I knew that. I was able to see the clip and remove it. From that point on, it was very easy to remove the old assembly and reinstall the new one. If I had to do it over again, I would have changed the sleeve at the same time that I changed the idler assembly because the assembly still wobbles on the pin more than I would like. However, it works fine so I won't worry about it until other repairs are needed.
The parts that I ordered from Parts Select were exact matches for the parts that I removed. They were in stock and were shipped the next business day. I would rate the repair as very easy. Read more...
PartSelect Number PS459481
Manufacturer Part Number 5303279394
If you have a leaky washer, then your tub seal may be the culprit. The tub seal assembly may also be known as the washer tub seal, and is a part for your washer. The function of this piece is to make sure water does not lead from between the outer tub and the spin basket from around your basket drive shaft within your washer. To replace your old part with this one you will need a flathead screwdriver, Phillips head screwdriver, pliers, putty knife, 7/16 socket, spanner wrench, and a hammer.
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
Rick from Walkerton, IN
The primary problem was that the tub seal assembly was leaking.
1. I began by removing the two screws that hold the front panel in place. I then lifted the top free of the front panel and tilted it back to get it out of the way.2. Using my fingers, I released the tabs that connect the tub cover to the tub. It took some effort to remove the cap("Mechanism") over the bolt connecting the agitator to the agitator drive block because I didn't want to break the tab. Once removed, I removed the bolt and the agitator. I then removed the two bolts that clamp the Trunnion to the agitator shaft.
3. It took a little more effort to remove the tub because of corrosion, however, by rocking the tub back and forth I was able to work it free and remove it. I then removed the bolts connecting the Trunnion to the tub. It took a hammer to remove the Trunnion from the tub, once again because of corrosion.
4. After removing the tub, the seal assembly was next and it was easy to remove. I cleaned the agitator shaft with steel wool before beginning the reassembly to remove the corrosion. Before installing the new seal, I lubricated the agitator shaft and the inside of the seal with a silicone grease that is normally used for water faucets. The seal installed easily although care was required to insure that the seal did not twist out of place when sliding it down the agitator shaft.
5. The rest of the reassembly went easily. Since my old filter on the bottom of the tub was clogged, I replaced it with a new one. It took a little time to get every tab on the filter aligned properly so that it could be rotated into place, but it went easily. Everything else reassembled with no problems.
6. It took considerable time to figure out how to replace the drive belt idler arm assembly because I could not figure out how to remove the pin that the idler arm pivots on. I finally reviewed the parts list on-line again and determined that there is a small C-clip that holds it together. Once I knew that. I was able to see the clip and remove it. From that point on, it was very easy to remove the old assembly and reinstall the new one. If I had to do it over again, I would have changed the sleeve at the same time that I changed the idler assembly because the assembly still wobbles on the pin more than I would like. However, it works fine so I won't worry about it until other repairs are needed.
The parts that I ordered from Parts Select were exact matches for the parts that I removed. They were in stock and were shipped the next business day. I would rate the repair as very easy. Read more...
Appliance Type
Related Parts
- Frigidaire Washer Belts
- Frigidaire Washer Brackets and Flanges
- Frigidaire Washer Caps and Lids
- Frigidaire Washer Circuit Boards and Touch Pads
- Frigidaire Washer Dispensers
- Frigidaire Washer Doors
- Frigidaire Washer Handles
- Frigidaire Washer Hardware
- Frigidaire Washer Hinges
- Frigidaire Washer Hoses and Tubes
- Frigidaire Washer Knobs
- Frigidaire Washer Latches
- Frigidaire Washer Motors
- Frigidaire Washer Panels
- Frigidaire Washer Pumps
- Frigidaire Washer Seals and Gaskets
- Frigidaire Washer Springs and Shock Absorbers
- Frigidaire Washer Switches
- Frigidaire Washer Timers
- Frigidaire Washer Valves
Popular Frigidaire Washer Models
Below are the most popular Frigidaire Washer models we have. Enter your model number in the search box to find your model.
- FAFW3801LW3
- ATF6000FS1 Residential
- FAFW3511KW0
- FFFW5000QW0 WASHER
- GLTF1670AS0 Residential
- GLTF2940FS1 Residential
- FAFS4272LW0
- FWT449GFS1 Residential
- ATF6000ES1 Residential
- ATF6700FS1 Residential
- FAFW4011LW0
- GLTF2940ES0 Residential
- ATF8000FS1 Residential
- FWT445GES2 Residential
- GLTF2940ES3 Residential
- FTF530FS1 Residential
- GLTF2940FS2
- FTF2140FS1 Residential
- GLTF1040AS0 Residential
- LTF2140FS1 Residential