My Orders
Frigidaire Washer Valves
GET YOUR OFFICIAL Frigidaire PARTS TO ENSURE VICTORY
Popular Frigidaire Washer Valves
This OEM water inlet valve assembly with flow meter fits select Frigidaire, Electrolux, White Westinghouse, and Tappan washers. It regulates water flow for efficient operation and energy savings. Unplug the washer and shut off the water supply before installing. Refer to your owner’s manual for model-specific guidance. Verify compatibility before ordering.
This OEM water inlet valve assembly with flow meter fits select Frigidaire, Electrolux, White Westinghouse, and Tappan washers. It regulates water flow for efficient operation and energy savings. Unplug the washer and shut off the water supply before installing. Refer to your owner’s manual for model-specific guidance. Verify compatibility before ordering.
The water inlet and dispenser valve is used in washing machines. The function of this part is to control and monitor the amount of water flow into the washer. If there is leaking during use, your machine will not fill with water, or there is no hot or cold water entering the washer, it is important to replace the water valve to solve the problem. For this repair, you will need a Phillips head screwdriver and a flathead screwdriver. For installation instructions, refer to the manual provided by the manufacturer. Remember to unplug your appliance from the power source before beginning this repair.
The water inlet and dispenser valve is used in washing machines. The function of this part is to control and monitor the amount of water flow into the washer. If there is leaking during use, your machine will not fill with water, or there is no hot or cold water entering the washer, it is important to replace the water valve to solve the problem. For this repair, you will need a Phillips head screwdriver and a flathead screwdriver. For installation instructions, refer to the manual provided by the manufacturer. Remember to unplug your appliance from the power source before beginning this repair.
Installation Instructions
Julie from Lancaster, OH
Valve dispener would spray water all over inside of washer.
My husband made the repair. First, he had to remove the dryer off of the top of the washer since it's a stacking unit. Disconnect water lines. Next he removed two screws from the back of the washer that allows you to remove the lid. Now unsnap a trim piece that is on the back surrounding the water connections and an exhaust port. Rea
... Read more
ch inside the washer, turn the exhaust port unlocking it and pushing out the back of the washer as far as you can to get it out of the way. Disconnect the electrical lines from the valve dispenser. Remove the two screws that fasten the valve dispenser to the washer. Install the new dispenser and reassemble.
Read less
This water inlet valve works with washers
This water inlet valve works with washers
Frigidaire Washer Dispenser Housing And Water Inlet Valve Assembly
Part #5304512102
$135.25
In Stock
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
The water inlet valve has two ports for water to enter and controls the flow of water into a washing machine. Hot, cold, and warm water can easily enter the washer this way. If the water inlet valve is in any way damaged or defective, it may be slow to fill or even leak. Before beginning this replacement, make sure to unplug the washer from the power range or shut off the house circuit breaker. Remember to wear gloves for safety. Refer to the installation instructions and the diagram provided by the manufacturer for best results and accuracy.
The water inlet valve has two ports for water to enter and controls the flow of water into a washing machine. Hot, cold, and warm water can easily enter the washer this way. If the water inlet valve is in any way damaged or defective, it may be slow to fill or even leak. Before beginning this replacement, make sure to unplug the washer from the power range or shut off the house circuit breaker. Remember to wear gloves for safety. Refer to the installation instructions and the diagram provided by the manufacturer for best results and accuracy.
Installation Instructions
alvaro from east hampton, NY
Washer Continued To Fill To Point Of Overflow
First I removed the top panel held by four screws at rear of panel, pulling the panel foward and up. Then disconnected the power and water connections. Then I removed the two screws holding the flow valve to the washer rear panel,pulled the valve foward ,removed the two electric connectors, pinched the water clamp with pliers and remo
... Read more
ved the water connection to the valve. Then replaced with the new valve followed the above steps in reverse order, finishing up by re placing the water connections and power. Then checked fo proper replacenent and leaks before replacing top panel.
Read less
This water inlet valve controls the flow of water into your appliance, ensuring proper filling during wash cycles. Ideal for replacing a faulty valve that causes leaks or filling issues, it restores efficient operation. Installation involves disconnecting power and water supply, removing the old valve, and securing the new one in place.
This water inlet valve controls the flow of water into your appliance, ensuring proper filling during wash cycles. Ideal for replacing a faulty valve that causes leaks or filling issues, it restores efficient operation. Installation involves disconnecting power and water supply, removing the old valve, and securing the new one in place.
This genuine OEM washer water inlet valve controls the flow of hot and cold water into the tub during wash cycles, ensuring accurate water levels and temperatures. Operated by dual solenoids, the valve opens and closes based on signals from the control board to manage water supply efficiently. Designed for durability and precision, this replacement part restores proper functionality when the original valve is worn or defective. Professional installation is recommended for best performance.
This genuine OEM washer water inlet valve controls the flow of hot and cold water into the tub during wash cycles, ensuring accurate water levels and temperatures. Operated by dual solenoids, the valve opens and closes based on signals from the control board to manage water supply efficiently. Designed for durability and precision, this replacement part restores proper functionality when the original valve is worn or defective. Professional installation is recommended for best performance.
Installation Instructions
William from Tivoli, NY
Water valve froze, and cracked
I have a stackable unit. My son and I removed the dryer from the top of the washer, removed the top, and rear panels on the washer. We romoved the old water valve, and installed the new one. It was a VERY simple repair.
This washer water inlet valve controls the flow of hot and cold water into the machine, helping ensure proper fill levels, temperature balance, and consistent wash performance. Using electrically operated solenoids, it opens and closes based on the selected cycle to regulate water intake. Replacement is recommended if the washer is slow to fill, not filling at all, leaking, or experiencing inconsistent water levels, helping restore reliable and efficient operation.
This washer water inlet valve controls the flow of hot and cold water into the machine, helping ensure proper fill levels, temperature balance, and consistent wash performance. Using electrically operated solenoids, it opens and closes based on the selected cycle to regulate water intake. Replacement is recommended if the washer is slow to fill, not filling at all, leaking, or experiencing inconsistent water levels, helping restore reliable and efficient operation.
This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.
This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.
Installation Instructions
william from goldsboro, NC
the cold water would not stop from draining into the wash tub
unscrew the top from the back. lift it up. Support the top and then unplugged the old valve, unscrewed it took the drain hose off it and presto the old came right out. align the new one was a little tricky and attached the drain hose and tightened the screw hook up the wires reattach the top and I was done. 30/45 minutes. I was really sur
... Read more
prized that the part I ordered was the same one I took out. Thanks for being there.
Read less