Maytag Washer Motors
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Maytag Washer Motors
Your Price
$21.45
In Stock
Maytag Washer Direct Drive Motor Coupling
First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pump.
The motor comes off next. Unplug the electrical connector from the motor and two wires from the capacitor. Remove the two screws holding the clamps in place and then pop off the two clamps. You will need to hold up the motor with one hand while you remove the clamps or it will fall to the floor once the clamps are removed.
One piece of the coupling assemble will be attached to the motor and the other will be attached to the gearcase drive shaft. If you want to clean up the mess created by the shredded rubber center piece of the coupling assembly you will have to take off the motor mounting plate. It is held on by two bolts and removing it makes installing the coupling easier but probably not necessary.
Push the back half of the coupling on to the gearcase drive shaft until the shaft is flush with the face of the coupling. Install the new rubber center piece on to the coupling then re-install the motor mounting plate. Install the other half of the coupling on to the motor shaft and lift the motor up to the coupling. You have to rotate the motor shaft by spinning the fan blades until the coupling lines up so you can slide it into the other half of the coupling. Then just reattach the motor, connectors and water pump in the reverse order of disassembly. Read more...
PartSelect Number PS1485646
Manufacturer Part Number 285753A
This direct drive motor coupling (Direct Drive Washer Motor Coupling, Motor Coupling, Washer Motor Coupling, Coupling Kit) provides a cushioned connection between the transmission and the motor shaft. It attaches to the direct-drive transmission and the motor shaft. If this part is defective it will affect the agitator in your washer because of its direct connection with the motor. Your washer may not agitate, spin slowly, or not spin at all. The coupling must be replaced when there is no longer a consistent connection between the transmission and the motor shaft. The coupling can wear over time because of its location between two major parts of the dryer. It is subject to material fatigue over time from normal use, or breakage caused by frequent overloading. The part measures approximately 2 inches in diameter, and is constructed of plastic and metal. This model comes in black/white.
Fixes these symptoms
- Burning smell
- Draining Issues
- Leaking
- See more...
Installation Instructions
Jeff from Wayne, NJ
No movement from Basket & agitator
The job looked intimidating but turned out to be very easy.First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pump.
The motor comes off next. Unplug the electrical connector from the motor and two wires from the capacitor. Remove the two screws holding the clamps in place and then pop off the two clamps. You will need to hold up the motor with one hand while you remove the clamps or it will fall to the floor once the clamps are removed.
One piece of the coupling assemble will be attached to the motor and the other will be attached to the gearcase drive shaft. If you want to clean up the mess created by the shredded rubber center piece of the coupling assembly you will have to take off the motor mounting plate. It is held on by two bolts and removing it makes installing the coupling easier but probably not necessary.
Push the back half of the coupling on to the gearcase drive shaft until the shaft is flush with the face of the coupling. Install the new rubber center piece on to the coupling then re-install the motor mounting plate. Install the other half of the coupling on to the motor shaft and lift the motor up to the coupling. You have to rotate the motor shaft by spinning the fan blades until the coupling lines up so you can slide it into the other half of the coupling. Then just reattach the motor, connectors and water pump in the reverse order of disassembly. Read more...
Your Price
$97.46
In Stock
Maytag Washer Drive Motor With Pulley
1) Removed back - 6 screws
2) Removed dryer vent - 2 screws on top, 3 on bottom
3) Popped the top open
4) Removed Front of dryer cabinet - 2 screws
5) Removed Belt
6) Removed Drum
7) Cleaned up all lint
8) Pop off motor retainers front and back
Here is the tricky part for me.
9) Removed vent fan on back of motor.
I did not know that the back of the fan was square, and you could put an open ended wrench on it to hold it while you also have a vice grip on the front motor shaft. Then its a simple left to loosey operation. I first tryed to turn the fan blade to take it off, but proved to be to tight.
10) Repeat backwards to reassemble
While I had it apart I also replaced the Drum support rollers & Installed a new belt. Not that diffucult of a repair Good Luck, was certainly better than buying a new one at + $300.00 at Black Friday rates. Read more...
PartSelect Number PS334304
Manufacturer Part Number 279827
This OEM drive motor is designed to operate the drum in electric and gas dryers by turning the drive belt, enabling proper rotation during drying cycles. Compatible with most Whirlpool-incorporated dryer brands manufactured before 1996, it includes a pre-attached pulley, which is not available separately. If the motor has shorted out or failed, the drum will no longer spin, and replacement is necessary to restore full functionality. Installation requires disconnecting the dryer from its power source before removing the old motor and installing the new one. This component is sold individually and meets original equipment standards for performance and reliability.
Fixes these symptoms
- Drum Not Spinning
- Noisy
- Will Not Start
- See more...
Installation Instructions
Mark from Fremont, NE
Wife told me Dryer would make a funny sound, then stop + had an a funny smell as well. The Electric motor that drove the unit was overheating and locking up, It was time to be replace.
The best part of my repair was I had everything back in service in 3 days. And one of these days was to consider just buying a new dryer. Had parts overnited and all parts fit and easy to replace.1) Removed back - 6 screws
2) Removed dryer vent - 2 screws on top, 3 on bottom
3) Popped the top open
4) Removed Front of dryer cabinet - 2 screws
5) Removed Belt
6) Removed Drum
7) Cleaned up all lint
8) Pop off motor retainers front and back
Here is the tricky part for me.
9) Removed vent fan on back of motor.
I did not know that the back of the fan was square, and you could put an open ended wrench on it to hold it while you also have a vice grip on the front motor shaft. Then its a simple left to loosey operation. I first tryed to turn the fan blade to take it off, but proved to be to tight.
10) Repeat backwards to reassemble
While I had it apart I also replaced the Drum support rollers & Installed a new belt. Not that diffucult of a repair Good Luck, was certainly better than buying a new one at + $300.00 at Black Friday rates. Read more...
Your Price
$158.79
In Stock
Maytag Washer 2speed Drive Motor 60hz 120v
PartSelect Number PS11743427
Manufacturer Part Number WP661600
This is a 2-speed drive motor for your washing machine. The motor rotates the spin basket when the washing machine is in spin or tumbling mode. You will likely need to replace the motor if you are experiencing burning smells or your washer will not start. The tools you will need to make this repair include a number two Phillips screwdriver, a flat-blade screwdriver, and a 5/16 nut driver.
Fixes these symptoms
- Burning smell
- Spinning Issues
- Will not agitate
- See more...
Installation Instructions
Lowell from Dover, DE
Washer had water leak in lower front and would not drain.
Laid the washer on its back and found leak in water pump. Found out it was caused by vibration from motor with bad bearing. Removed pump and motor which were held on by clips. Both were removed and replaced without removing cabinet from machine.
Read more...
Your Price
$132.29
In Stock
Maytag Washer Rotor
PartSelect Number PS11769961
Manufacturer Part Number W10915701
This motor rotor connects to the spin basket shaft and rotates the spin basket in washers. Unplug the washer before installing, and wear work gloves for safety. Verify compatibility with your model before purchasing.
Fixes these symptoms
- Spinning Issues
- Will not agitate
- See more...
Your Price
$177.05
On Order
Maytag Washer Motor With Pulley
Note: it ios easier to install the belt fully on the two smaller puleys attcahed to the drive motor and pump and then wrap as much as you can around the larger drum pulley. Hold the belt in one hand and turn the drum pulley clockwise with the other and the belt will follow and install. reverse steps to reassemble. Read more...
PartSelect Number PS11738839
Manufacturer Part Number WP21001950
This motor is a 2 speed, 1/2 HP, 120V, 60Hz.
Fixes these symptoms
- Burning smell
- Will not agitate
- Will not drain
- See more...
Installation Instructions
Michael from Warminster, PA
The belt and pulley on the drive motor broke
unplug the washer. Removed the top of the washer by removing the hold scews and tabs on the upper back. Place a scew drive under the front and pry up to release the snap tabs. Then the front panel by removing the two screws on top and lift the panel up to expose the motor at bottom front. Remove the motor cover (plastic)and motor from the base, replace the pulley on the shaft (you may need to break or pry the old pulley off) install the new pulley making sure it is all the way up the shaft locking the tabs into the shat groove. Reinstallmotor to the base. To replace the belt, tilted the unit backwards to access the pulleys from the bottom and installed.Note: it ios easier to install the belt fully on the two smaller puleys attcahed to the drive motor and pump and then wrap as much as you can around the larger drum pulley. Hold the belt in one hand and turn the drum pulley clockwise with the other and the belt will follow and install. reverse steps to reassemble. Read more...
Your Price
$110.45
In Stock
Maytag Washer Rotor
PartSelect Number PS12584381
Manufacturer Part Number W11260238
Stay at the forefront of appliance maintenance with this genuine ROTOR from Whirlpool. Specifically built for efficient compatibility with various models of Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef, its prime function is attaching to the spin basket shaft, thus aiding the rotation of the spin basket. Ensure safe installation by unplugging your washer and wearing work gloves for protection. Let ROTOR's performance consistency cater to your appliance care requirements. The significance of verifying your model and part number before ordering cannot be overemphasized for perfect fit and top-tier function. Remember, parts may appear identical, but critical differences in size and shape can impact performance.
Your Price
$192.49
In Stock
Maytag Washer Motor Rotor
PartSelect Number PS10064560
Manufacturer Part Number W10754161
This washer rotor is a genuine replacement component designed to drive the spin basket in select washing machines. It functions by generating a magnetic field that interacts with the stator, producing the torque required to rotate the drum at various speeds during wash and spin cycles. The rotor plays a critical role in ensuring smooth, stable operation, reducing noise and vibration while enhancing energy efficiency. Common symptoms indicating the need for replacement include a washer that won’t spin, leaves clothes excessively wet, or produces unusual motor sounds. Compatible with a range of Whirlpool-family brand models, installation should be performed with the appliance unplugged and may require basic tools and reference to model-specific instructions.
Fixes these symptoms
- Spinning Issues
- Will not agitate
- See more...
Your Price
$128.66
In Stock
Maytag Washer Drive Motor - One Speed 120v
PartSelect Number PS2003768
Manufacturer Part Number 12002351
Are you looking to give your Samsung dishwasher a new lease of life? We've just the thing you need ? the authentic OEM Samsung Upper Basket Assembly. As a genuine Samsung part, it's designed exactly for your dishwasher model. That means fitting it is as straightforward as can be; just use your appliance's manual for step-by-step instructions. Made from sturdy white plastic, this upper basket is built to last. But it's not just about toughness; it's also about doing an amazing job. It securely holds your dishes in place throughout the dishwashing cycle, so you can trust it to deliver spotless dishes every time. This upper dishrack is meant to work smoothly with your Samsung dishwasher models, promising perfect performance in each and every wash. So why wait? Bring back your dishwasher?s optimal efficiency with this reliable part.
Fixes these symptoms
- Burning smell
- Will not agitate
- Will Not Start
- See more...
Installation Instructions
Eric from Seabeck, WA
Washer motor start windings burned up
The motor was easy to replace: unplug the wiring harness, slip off the belts, release the tension springs from the motor carriage with needle-nose pliers, and then unbolt the motor carriage with socket set and remove from the washer. Remove the pulley from the old motor with allen wrench and transfer the carriage to the new motor. Reverse operation for everything and you are back in business. The hardest part was the far back screw holding the carriage, a wobble extension helped.
Read more...
Your Price
$160.29
In Stock
Maytag Washer Stator
PartSelect Number PS11769960
Manufacturer Part Number W10915700
Introducing the STATOR from Whirlpool - a genuine OEM part, meticulously crafted for select models of Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef appliances. This motor stator plays an integral role in the functionality of your washer, working harmoniously with the motor rotor to effortlessly rotate the spin basket. To ensure the longevity of your appliance and to keep it running smoothly, it's advised to unplug your washer during the installation of this part. Remember, even though parts might appear same, subtleties in size and shape can make a significant difference. Therefore, please verify that the part number is accurate for your specific model before purchasing. Lastly, for your safety, always wear work gloves during the installation process.
Your Price
$185.48
In Stock
Maytag Washer Drive Motor
PartSelect Number PS11770267
Manufacturer Part Number W11026785
The drive motor spins the spin basket and drives the agitator or spin basket in the agitation or tumbling mode.
Related Maytag Washer Parts
- All Maytag Washer parts
- Maytag Washer Agitators
- Maytag Washer Bearings
- Maytag Washer Belts
- Maytag Washer Brackets and Flanges
- Maytag Washer Caps and Lids
- Maytag Washer Circuit Boards and Touch Pads
- Maytag Washer Dispensers
- Maytag Washer Doors
- Maytag Washer Drawers and Glides
- Maytag Washer Drums and Tubs
- Maytag Washer Electronics
- Maytag Washer Elements and Burners
- Maytag Washer Filters
- Maytag Washer Fuses
- Maytag Washer Handles
- Maytag Washer Handles and Latches
- Maytag Washer Hardware
- Maytag Washer Hinges
- Maytag Washer Hoses and Tubes
- Maytag Washer Knobs
- Maytag Washer Latches
- Maytag Washer Legs and Feet
- Maytag Washer Lights and Bulbs
- Maytag Washer Panels
- Maytag Washer Power Cords
- Maytag Washer Pulleys
- Maytag Washer Pumps
- Maytag Washer Seals and Gaskets
- Maytag Washer Sensors
- Maytag Washer Springs and Shock Absorbers
- Maytag Washer Switches
- Maytag Washer Timers
- Maytag Washer Transmissions and Clutches
- Maytag Washer Valves
- Maytag Washer Wheels and Rollers
- Maytag Washer Wire Plugs and Connectors