My Orders
Maytag Washer Valves
GET YOUR OFFICIAL Maytag PARTS TO ENSURE VICTORY
Popular Maytag Washer Valves
This is an inlet valve for your washing machine. The inlet valve is an electrically controlled valve with a solenoid that opens and closes as needed, during the water filling cycle of the washing machine. This inlet valve features two inlets, one for hot and one for cold water, and three push-on valves that connect within your washing machine. If your washer is having issues filling or is leaking water from the area of the inlet valve, it needs to be replaced immediately. Replacing this valve will require a screwdriver and a wrench to replace. This inlet valve is an OEM part and is sold individually.
This is an inlet valve for your washing machine. The inlet valve is an electrically controlled valve with a solenoid that opens and closes as needed, during the water filling cycle of the washing machine. This inlet valve features two inlets, one for hot and one for cold water, and three push-on valves that connect within your washing machine. If your washer is having issues filling or is leaking water from the area of the inlet valve, it needs to be replaced immediately. Replacing this valve will require a screwdriver and a wrench to replace. This inlet valve is an OEM part and is sold individually.
Installation Instructions
Marian from GREYBULL, WY
Faulty fill valve
Did troubleshooting after code LF showed on indicator window. Did troubleshooting; checked hoses for obstructions and small filters on inlets. All good. Ordered new fill valve. Came in a few days, good service.
Removed control panel top by removing screws on back of control panel, then by pushing putty knife under each side to rele ... Read more ase spring clips. Carefully lifted cover and set onto lid. Photographed fill valve at left side as you are standing in front of machine. Removed screws with small ratchet. Carefully removed wires via clips. Lifted out valve.
Attached wires to new, set back into its place, replaced screws, tightened but not too tight so as to break part. Replaced control panel, pushing downward to engage spring clips, then replace screws on back.
Re attached hoses, ensuring they were on the correct sides, plugged machine into power, ran through cycle and VIOLA!! Worked perfectly!! After a couple weeks, still working perfectly! Was VERY happy it was only fill valve and not mother board as the cost was a fraction.
I found trouble shooting videos to be very helpful. Your service quite good.
Removed control panel top by removing screws on back of control panel, then by pushing putty knife under each side to rele ... Read more ase spring clips. Carefully lifted cover and set onto lid. Photographed fill valve at left side as you are standing in front of machine. Removed screws with small ratchet. Carefully removed wires via clips. Lifted out valve.
Attached wires to new, set back into its place, replaced screws, tightened but not too tight so as to break part. Replaced control panel, pushing downward to engage spring clips, then replace screws on back.
Re attached hoses, ensuring they were on the correct sides, plugged machine into power, ran through cycle and VIOLA!! Worked perfectly!! After a couple weeks, still working perfectly! Was VERY happy it was only fill valve and not mother board as the cost was a fraction.
I found trouble shooting videos to be very helpful. Your service quite good.
Read less
The water inlet valve on your washing machine is used to fill the tub with cold, warm, or hot water for the wash and rinse cycles. This part could have either a blue or green-colored valve body. There are two ports for water to enter and this valve is compatible with a half-inch ID hose. It has two 3/4-11x1/2 NHT hose threads. You may have a faulty valve if your washer is leaking, has no hot or cold water, will not stop filling with water, will not fill with water, fills and drains at the same time, or is noisy. To confirm that the valve is faulty, unplug the washer when the symptom occurs. If the washer continues to fill, then the inlet valve is defective.
The water inlet valve on your washing machine is used to fill the tub with cold, warm, or hot water for the wash and rinse cycles. This part could have either a blue or green-colored valve body. There are two ports for water to enter and this valve is compatible with a half-inch ID hose. It has two 3/4-11x1/2 NHT hose threads. You may have a faulty valve if your washer is leaking, has no hot or cold water, will not stop filling with water, will not fill with water, fills and drains at the same time, or is noisy. To confirm that the valve is faulty, unplug the washer when the symptom occurs. If the washer continues to fill, then the inlet valve is defective.
Installation Instructions
Don from Wyoming, MN
Washer stopped at rinse cycle
Removed the top and back panels. Replaced
compoments and reassembled.
Test run machine. Ran like new!
compoments and reassembled.
Test run machine. Ran like new!
This water inlet valve is for washers.
The water inlet valve controls the water flow into the washer.
Unplug the washer and shut off the water supply before installing this part. Wear work gloves to protect your hands.
This water inlet valve is for washers.
The water inlet valve controls the water flow into the washer.
Unplug the washer and shut off the water supply before installing this part. Wear work gloves to protect your hands.
Installation Instructions
Patricia from MURPHYSBORO, IL
Water would not fill the washer except for 4 inches.
Once we put in the new Water Inlet Valve, the auto sensor works now and I can wash any size load
This part is used to help control and balance the water temperature flowing in to the washer tub.
This part is used to help control and balance the water temperature flowing in to the washer tub.
Installation Instructions
Barb from Blackriver Falls, WI
fill valve bad
took back off then removed valve replaced with new one works good
This is a water inlet valve made for washing machines. This part is used to control the flow of water into the fill hose of the washing machine, to allow the washer to fill up with water. If your washing machine is not filling up with water properly, or if you are noticing leaks underneath your washing machine, the inlet valve has likely failed and you will likely need to replace it. This OEM inlet valve features two different inlets for hot and cold water but does not come with any other parts or accessories for installation. To replace this water inlet valve, you will need tools such as a screwdriver or wrench to gain access to it and remove it.
This is a water inlet valve made for washing machines. This part is used to control the flow of water into the fill hose of the washing machine, to allow the washer to fill up with water. If your washing machine is not filling up with water properly, or if you are noticing leaks underneath your washing machine, the inlet valve has likely failed and you will likely need to replace it. This OEM inlet valve features two different inlets for hot and cold water but does not come with any other parts or accessories for installation. To replace this water inlet valve, you will need tools such as a screwdriver or wrench to gain access to it and remove it.
Installation Instructions
Brian from VESTAL, NY
Water was dripping while the machine wasn’t running
Removed two screws that held the control panel from the back with a power drill. Pop the control panel loose with a screwdriver from the top of the machine with the quick disconnects. After turning both the hot and cold water off I remove the hoses with pliers removed two screws with the power drill that hold the water inlet valve in plac
... Read more
e disconnected the wire harness plug And removed water inlet valve swap, the original harness to the new water inlet valve and follow the steps backwards to finish
Read less
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
This dual-coil water inlet valve is a genuine OEM replacement designed to regulate the flow of hot and cold water into your washing machine. It connects directly to the appliance’s water lines and distributes water to the appropriate dispensers based on cycle settings. Engineered for compatibility with select Whirlpool, Maytag, KitchenAid, and other associated brand models, this valve ensures accurate water temperature control and efficient filling. Common symptoms of a faulty valve include water leaks or improper filling. Installation requires disconnecting power and water supply for safety. Sold individually.
This dual-coil water inlet valve is a genuine OEM replacement designed to regulate the flow of hot and cold water into your washing machine. It connects directly to the appliance’s water lines and distributes water to the appropriate dispensers based on cycle settings. Engineered for compatibility with select Whirlpool, Maytag, KitchenAid, and other associated brand models, this valve ensures accurate water temperature control and efficient filling. Common symptoms of a faulty valve include water leaks or improper filling. Installation requires disconnecting power and water supply for safety. Sold individually.
Installation Instructions
Jerry from Keenes, IL
washing machine giving f20 error code
removed washer top, checked supply hoses and inlet valve to make sure not clogged, replaced valve and while already there replaced flowmeter, reinstall top and hoses and checked machine operation, machine working fine and wife thinks i am her hero
This is an inlet valve for various washing machines. Inlet valves are responsible for opening and closing as needed, to allow water to enter the washer during the washing cycle. This inlet valve features a hot and cold-water valve, as well as the necessary wire harness to easily plug it in. Since inlet valves are an electrically controlled solenoid valve, they can fail either due to electrical failure such a short, or after long, extended use. If your inlet valve fails, your washer will likely relay an error code, or it simply will not wash your clothes due to the lack of water, and the valves will need to be replaced. Replacing this valve will require a screwdriver and/or socket wrench, and some disassembly of your washer will be necessary. This inlet valve is an individually sold OEM part and does not come with any accessories or other parts.
This is an inlet valve for various washing machines. Inlet valves are responsible for opening and closing as needed, to allow water to enter the washer during the washing cycle. This inlet valve features a hot and cold-water valve, as well as the necessary wire harness to easily plug it in. Since inlet valves are an electrically controlled solenoid valve, they can fail either due to electrical failure such a short, or after long, extended use. If your inlet valve fails, your washer will likely relay an error code, or it simply will not wash your clothes due to the lack of water, and the valves will need to be replaced. Replacing this valve will require a screwdriver and/or socket wrench, and some disassembly of your washer will be necessary. This inlet valve is an individually sold OEM part and does not come with any accessories or other parts.
Installation Instructions
melinda from HARROGATE, TN
Water would not stop flowing.
*be sure to turn water off, unplug machine, and unscrew the water hoses from the rear of the washer.
1. Removed screws from the back of the washer, just the top part where the controls are.
2. Removed the panel.
3. Use a putty knife or screw driver to pop off the top panel.
4. Remove the screws from the inlet valve.< ... Read more br />5. Unplug the wires connecting the inlet valve to the washer.
6. Lift out the old inlet valve.
7. Replace with the new inlet valve.
8. Plug the new wires into the washer.
9. Replace the screws in the inlet valve.
10. Replace the top.
11. Replace the rear panel and screws.
12. Reconnect the water hoses, careful not to mix the hot and cold.
13. Plug the machine back in and you're finished!
1. Removed screws from the back of the washer, just the top part where the controls are.
2. Removed the panel.
3. Use a putty knife or screw driver to pop off the top panel.
4. Remove the screws from the inlet valve.< ... Read more br />5. Unplug the wires connecting the inlet valve to the washer.
6. Lift out the old inlet valve.
7. Replace with the new inlet valve.
8. Plug the new wires into the washer.
9. Replace the screws in the inlet valve.
10. Replace the top.
11. Replace the rear panel and screws.
12. Reconnect the water hoses, careful not to mix the hot and cold.
13. Plug the machine back in and you're finished!
Read less
This water inlet valve is a key component in top-load washing machines, responsible for regulating the flow of hot and cold water into the appliance. It electronically opens and closes to deliver the correct amount of water, balances temperature for each cycle, and helps maintain proper water levels. Constructed from durable, high-quality materials, the valve is designed to withstand frequent use and prevent issues such as overfilling, insufficient water flow, or leaks. Replacing a faulty valve can resolve symptoms like the washer not filling, continuous water flow, uneven temperature control, or water leakage from the rear of the unit, restoring efficient and safe operation.
This water inlet valve is a key component in top-load washing machines, responsible for regulating the flow of hot and cold water into the appliance. It electronically opens and closes to deliver the correct amount of water, balances temperature for each cycle, and helps maintain proper water levels. Constructed from durable, high-quality materials, the valve is designed to withstand frequent use and prevent issues such as overfilling, insufficient water flow, or leaks. Replacing a faulty valve can resolve symptoms like the washer not filling, continuous water flow, uneven temperature control, or water leakage from the rear of the unit, restoring efficient and safe operation.
Installation Instructions
Armand from WESTPORT, MA
Water inlet nozzle was stripped and leak
Remove the front panel and back panel unplug the part unscrewed the part and replace it with the new one
What this part fixes:
- Does not dispense fabric softener or detergent
- Leaking
- No hot or cold water
Installation Instructions
Frederick from OSWEGO, NY
Fabric Softener dispenser would not drain out
Replaced the Whirlpool washer water inlet valve.
1. Unplug washer
2. Close Hot and Cold water valves
3. Remove top cover of the machine by taking out 3 screws in the top back. Slide top back and remove.
4. Water Inlet Valve is located on the back left side, remove tubing using a nutdriver to loosen the hose clamps.
... Read more
/>5. Water Inlet Valve is removed by removing the screw in the back of the valve and turning the valve clockwise a little.
Replace with the new one, connect hoses, put cover back on, open valves, plug it in.
6. Ran washer and Fabric Softener dispenser now works
1. Unplug washer
2. Close Hot and Cold water valves
3. Remove top cover of the machine by taking out 3 screws in the top back. Slide top back and remove.
4. Water Inlet Valve is located on the back left side, remove tubing using a nutdriver to loosen the hose clamps.
Replace with the new one, connect hoses, put cover back on, open valves, plug it in.
6. Ran washer and Fabric Softener dispenser now works
Read less
This is a water inlet valve for models of Whirlpool washing machines. The water inlet valve is designed to regulate and control the water entering the appliance depending on the cycle, using an electrical device called a solenoid. This water inlet valve features two inlets, one for hot water and one for cold, as well as a wire harness to power and control the electric solenoid of each. If your washer is having issues with filling, the inlet valve is likely bad or potentially worn out and in need of replacement. Replacing this valve will require a screwdriver, wrench, and pliers. This water inlet valve is an OEM part from Whirlpool and is sold individually.
This is a water inlet valve for models of Whirlpool washing machines. The water inlet valve is designed to regulate and control the water entering the appliance depending on the cycle, using an electrical device called a solenoid. This water inlet valve features two inlets, one for hot water and one for cold, as well as a wire harness to power and control the electric solenoid of each. If your washer is having issues with filling, the inlet valve is likely bad or potentially worn out and in need of replacement. Replacing this valve will require a screwdriver, wrench, and pliers. This water inlet valve is an OEM part from Whirlpool and is sold individually.
Installation Instructions
John from SAINT JOSEPH, MI
Leaking water inlet valve assembly
Remove upper rear panel with drill driver and 1/4" nut driver bit. using the angle bit holder and torx bit remove the two screws holding the assembly in place. Slide out the old assembly and disconnect the wiring harness at the machine. Slide new assembly in place. While holding it down start both screws by hand, then use the driver/an
... Read more
gle holder to tighten screws. Reattach the wiring harness and rear plate(s).
Read less