Maytag Washer Belts
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Maytag Washer Belts
Your Price
$29.47
In Stock
Maytag Washer Drive Belt
PartSelect Number PS11747978
Manufacturer Part Number WPW10006384
This genuine OEM drive belt is designed to transfer power from the motor to the drum in select Whirlpool, Maytag, Kenmore, and other compatible washing machines. Operating at 115 volts and 60 Hz, the belt enables the drum to spin and agitate during wash and spin cycles, ensuring effective cleaning and rinsing. Manufactured to Whirlpool’s specifications, this replacement part offers reliable performance and a precise fit. Common symptoms of a worn or broken belt include the drum not spinning, unusual noises, or a burning smell during operation. Replacing the belt can restore proper function and prevent further mechanical issues. Always verify compatibility with your specific model before ordering.
Fixes these symptoms
- Burning smell
- Cycle Not Advancing
- Noisy and Marks Left on Clothes
- See more...
Installation Instructions
Jerry from WALLA WALLA, WA
Noise on bottom of Washer louder as time went on. 1 1/2 years
Well, first investigated and found loose nut on drive clutch. First take off the two screws with nut drive then cover off using a screwdriver blade to snap off the cover. Then socket ratchet to take off the nut on drive clutch. take off belt by slowly rotating the drive gear. two screws that hold the electronics to the upper drive clutch and put aside, so you can snap off the cover for drive clutch on upper part with screwdriver and off the parts come and install whole unit back as took it apart. Line up the new upper clutch so that is position as was before. (Using parts diagram helps a lot as www. partsselect.com has for you or Maytag.com.) Then put the electronic part board back on and the gear and nut. Make sure it is tight by several attempts to make sure it's snugged up good and then slowly roll belt back on the pulley and motor drive. Put your cover guard back on with two screws and done.
Read more...
Your Price
$32.63
In Stock
Maytag Washer Belt Kit
I pulled the washing machine away from the wall and tilted it bacwards and found the pump belt was off the pully and the drive belt was badly damaged. I replaced the 2 belts which took no tools and about 3 minutes to accomplish then resecured the front panel, pushed back in place and leveled. Complete repair from diagnosis to back in operation took less than 15 minutes. Read more...
PartSelect Number PS2005284
Manufacturer Part Number 12112425
This kit includes both the drive belt and the pump belt which are both V-shaped. If your washer does not toss, spin, or drain water properly, this might be because one of these belts has worn or stretched out. This results in the belt losing its grip and no longer driving the pump. The pump belt is black and made of rubber. The pump belt is located between the motor and pump underneath the washer. Simply remove the belt and hook the new one around the pulley. You may need to loosen or tighten the belt to ensure it is set in place properly.
Fixes these symptoms
- Burning smell
- Leaking
- Noisy
- See more...
Installation Instructions
Charles from Whitman, MA
Drum would not drain and there was a banging noise when the drum spun
I removed the 2 phillips screws on the bottom of the front panel. Then checked around to find the belts were actually below the floor panel.I pulled the washing machine away from the wall and tilted it bacwards and found the pump belt was off the pully and the drive belt was badly damaged. I replaced the 2 belts which took no tools and about 3 minutes to accomplish then resecured the front panel, pushed back in place and leveled. Complete repair from diagnosis to back in operation took less than 15 minutes. Read more...
Your Price
$47.40
In Stock
Maytag Washer Belt
PartSelect Number PS12578772
Manufacturer Part Number W11239857
This drive belt connects the washing machine’s motor to the system, helping spin the basket. If the washer is having trouble spinning, the belt may need replacement. Ensure compatibility before ordering and unplug the washer before installation.
Fixes these symptoms
- Burning smell
- Noisy and Marks Left on Clothes
- Spinning Issues
- See more...
Installation Instructions
Armando from UNION CITY, CA
Screeching noise when starting the washing cycle. Especially with heavy loads.
The belt in this model is underneath the washing machine. Disconnect water lines and power cords, set up the drain hose in a bucket to avoid water spilling on the floor, tip the washing machine on its back, remove two bolt screws holding the plastic covering the belt, remove the old belt, and install the new one.
Read more...
Your Price
$16.07
In Stock
Maytag Washer Drive Belt - 51 Inches Long
PartSelect Number PS11738882
Manufacturer Part Number WP21352320
This V-style drive belt measures 51 inches long and 3/8 inches wide. The belt is made to slip on the motor pulley to bring the basket up to the speed required. Continued use can result in the belt suffering from wear and tear. Replace the V-style drive belt if you notice that it looks damaged. The most common symptoms of a damaged drive belt include: a burning smell or a loud grinding noise coming from the washer; the drum will not spin, spins slowly, or will not agitate; the washer shakes and moves, will not start, or will not drain.
Fixes these symptoms
- Burning smell
- Leaking
- Shaking and Moving
- See more...
Installation Instructions
Ranse from Layton, UT
Pump was making a grinding noise
The pump is located behind a small panel on the back, lower left side of my washer. It's attached to the bottom frame with 3 screws. It has two hoses attached, each with one spring clamp. Lift one side of the washer and slip the drive belt off the pully. Release the spring clamps on the hoses with a pair of pliers and remove the hoses. A small amount of water will drain from the hoses and pump when removed. Remove the three screws holding the pump to the frame and remove the pump. Install the new pump in the same position. Reattach the hoses, replace the belt, and reinstall the cover panel. That's all there is to it.
Read more...
Your Price
$33.69
In Stock
Maytag Washer Drive Belt 52 Inches Long
PartSelect Number PS11739438
Manufacturer Part Number WP22003483
This washing machine drive belt is used with some clothes washers. This belt is all black in color and is made entirely of rubber.
Fixes these symptoms
- Burning smell
- Leaking
- Spinning Issues
- See more...
Installation Instructions
James from Hueytown, AL
Washer tub would not spin, pump would empty water from tub.
Lay washer on front, removed belt. Removed center pulley with thrust bearing (pulley was worn on upper end, against thrust bearing, thrust bearing was worn also). Installed new thrust bearing & pulley kit. Cleaned & lubed slots that motor insulators slide in, installed new belt.
Read more...
Your Price
$23.60
In Stock
Maytag Washer Belt
PartSelect Number PS12349341
Manufacturer Part Number W11213879
This washing machine drive belt is a genuine OEM replacement designed to connect the motor to the drum, enabling proper spinning and agitation during wash and spin cycles. Made from high-quality, durable rubber, it ensures smooth operation and long-lasting performance. Ideal for fixing issues such as slow spinning, unusual noises, or a drum that does not move. Installation is straightforward—disconnect power, remove the old belt, and fit the new one securely to restore efficient functionality.
Installation Instructions
Lucas from ARKANSAS CITY, KS
Worn belt
Remove the guard that is held in place with two screw. Removed the old belt and rolled on the new. Watch your fingers.
Read more...
Your Price
$30.53
In Stock
Maytag Washer Drive Belt And Motor Isolator Kit
PartSelect Number PS2003327
Manufacturer Part Number 12001788
This kit contains a flat drive belt, two motor isolators, and an instructions sheet. The drive belt is made to slip on the pulley until the basket gets up the desired speed.
Fixes these symptoms
- Burning smell
- Spinning Issues
- Spins slowly
- See more...
Installation Instructions
richard from austin, MN
Drains but doesn't spin, door lock does not engage.
Door locked light did not come on and did not have 120 VAC across the Wax Motor. Also the Wax Motor did not extend out to make contact with the Door Lock, Spin Enable Switch. General guidance is to replace drive belt and to replace Wax Motor along with the Door Lock, Spin Enable Switches (total of two limit switches). This did not correct the problem. Checked for power and traced loss of power back to the Control Board where resistor R11 was found to be burnt out. Replaced Resistor with new Carbon Film unit, rating of 3.9 K-ohms, 1/4 W and 5%. As a prcaution, replace the Triac (manufactue part number NTE5657), component identified as Q6, rating of 0.8 Amp, 600 VAC. Semiconductor parts must be obtained from somewhere other than Parts Select (unable to find in the small town I live in, I located on the internet at Mouser.com). Unit works great now.
Read more...
Your Price
$52.67
In Stock
Maytag Washer Drive Belt
PartSelect Number PS11754067
Manufacturer Part Number WPW10388414
This drive belt is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt get wear and tear.
NOTE: Per Manufacture, belt measures 48.22" long uninstalled and the belt will stretch To 51.53" when installed.
Fixes these symptoms
- Burning smell
- Spinning Issues
- Spins slowly
- See more...
Installation Instructions
Francis from Rochester, NY
Washer made loud banging noise during spin cycle
I first removed the back panel held on by about 10 screws. I removed the drive belt from the pulley, then removed the lock nut securing the pulley to the drum & removed the pulley. Attached the new pulley to the drum, tightened on the lock nut, attached the new belt & ran a spin cycle. When that went OK I replaced the back panel & the washer was back in service.
Read more...
Your Price
$54.24
In Stock
Maytag Washer Belt
PartSelect Number PS11751386
Manufacturer Part Number WPW10260319
Are you struggling with water control in your washer? The Frigidaire Water Inlet Valve could be exactly what you need. This authentic OEM part is the key to getting your washer back to its optimum function. It manages the water flow in your machine, making sure each wash is just right. Why is this important? The right amount of water ensures a thorough clean, which means your laundry comes out perfectly every time. The Frigidaire Water Inlet Valve is not just reliable, it?s essential - and it puts you back in control of your washer. There's even more good news. This part is designed to fit seamlessly into specific models of Frigidaire, Electrolux, White Westinghouse, and Tappan appliances. That means easy installation for you - no need to worry about mismatched parts or complicated setups. Just remember to unplug your washer and cut off the water supply for safety when installing. And it's a good idea to wear work gloves to protect your hands. So, take a step towards better laundry days with the Frigidaire Water Inlet Valve. It's more than just a part ? it's the solution to your appliance troubles. Enjoy the reassurance and improved functionality that this genuine Frigidaire part brings to your washer.
Your Price
$51.61
In Stock
Maytag Washer Drive Belt
Guide new belt onto Washer Large Wheel. Use a pair of pliers to hold belt onto wheel as one turns the large washer belt wheel, guiding belt onto wheel. Note belt will be tight. Seems like belt will not fix but keep going it will fit, you might even hear it pop on.
Old Part number (W10116215) new replacement Part number (W10388418).
New replacement washer belt fits tight, that is ok. Read more...
PartSelect Number PS11754068
Manufacturer Part Number WPW10388418
The main drive belt is designed to ride on the pulley until the basket gets up to speed.
Fixes these symptoms
- Will not agitate
- See more...
Installation Instructions
Robert from OAKDALE, CT
Replace worn washer belt
Remove old belt, rotate large washer belt wheel, guiding belt off large wheel.Guide new belt onto Washer Large Wheel. Use a pair of pliers to hold belt onto wheel as one turns the large washer belt wheel, guiding belt onto wheel. Note belt will be tight. Seems like belt will not fix but keep going it will fit, you might even hear it pop on.
Old Part number (W10116215) new replacement Part number (W10388418).
New replacement washer belt fits tight, that is ok. Read more...
Related Maytag Washer Parts
- All Maytag Washer parts
- Maytag Washer Agitators
- Maytag Washer Bearings
- Maytag Washer Brackets and Flanges
- Maytag Washer Caps and Lids
- Maytag Washer Circuit Boards and Touch Pads
- Maytag Washer Dispensers
- Maytag Washer Doors
- Maytag Washer Drawers and Glides
- Maytag Washer Drums and Tubs
- Maytag Washer Electronics
- Maytag Washer Elements and Burners
- Maytag Washer Filters
- Maytag Washer Fuses
- Maytag Washer Handles
- Maytag Washer Handles and Latches
- Maytag Washer Hardware
- Maytag Washer Hinges
- Maytag Washer Hoses and Tubes
- Maytag Washer Knobs
- Maytag Washer Latches
- Maytag Washer Legs and Feet
- Maytag Washer Lights and Bulbs
- Maytag Washer Motors
- Maytag Washer Panels
- Maytag Washer Power Cords
- Maytag Washer Pulleys
- Maytag Washer Pumps
- Maytag Washer Seals and Gaskets
- Maytag Washer Sensors
- Maytag Washer Springs and Shock Absorbers
- Maytag Washer Switches
- Maytag Washer Timers
- Maytag Washer Transmissions and Clutches
- Maytag Washer Valves
- Maytag Washer Wheels and Rollers
- Maytag Washer Wire Plugs and Connectors