Drive Belt and Motor Isolator Kit 12001788 | Official Whirlpool Part | Fast Shipping | PartSelect
Drive Belt and Motor Isolator Kit – Part Number: 12001788
Drive Belt and Motor Isolator Kit – Part Number: 12001788 https://partselectcom.azureedge.net/Schematics/Maytag/59115.gif

Drive Belt and Motor Isolator Kit

Product Description

Drive Belt and Motor Isolator Kit Specifications

This kit contains a flat drive belt, two motor isolators, and an instructions sheet. The drive belt is made to slip on the pulley until the basket gets up the desired speed.

How Buying OEM Parts Can Save You Time and Money

Troubleshooting

This part fixes the following symptoms:

Noisy | Pumps but will not spin | Burning smell | Will not agitate

This part works with the following products:

Washer, Washer Dryer Combo.

This part works with the following brands:

Maytag, Crosley, Amana.

Part # 12001788 replaces these:

12001435, 12001788, 12001788VP, 22002040, 22002313, 785411, AP4009041.
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Part Videos

Replacing your Maytag Washer Drive Belt and Motor Isolator Kit

Customer Repair Stories
Average Repair Rating: 3.1 / 5.0, 9 reviews What's this?
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
richard from austin, MN
Difficulty Level:
Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Screw drivers, Socket set
Parts Used:
WP6-912678, WPY912679, 22002290, WP22002162, WP22002119, 12001788
Drains but doesn't spin, door lock does not engage.
Door locked light did not come on and did not have 120 VAC across the Wax Motor. Also the Wax Motor did not extend out to make contact with the Door Lock, Spin Enable Switch. General guidance is to replace drive belt and to replace Wax Motor along with the Door Lock, Spin Enable Switches (total of two limit switches). This did not correct the problem. Checked for power and traced loss of power back to the Control Board where resistor R11 was found to be burnt out. Replaced Resistor with new Carbon Film unit, rating of 3.9 K-ohms, 1/4 W and 5%. As a prcaution, replace the Triac (manufactue part number NTE5657), component identified as Q6, rating of 0.8 Amp, 600 VAC. Semiconductor parts must be obtained from somewhere other than Parts Select (unable to find in the small town I live in, I located on the internet at Mouser.com). Unit works great now.
97 of 137 people found this instruction helpful.
Was this instruction helpful to you?
DANIEL from WEST CHESTER, PA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Wrench (Adjustable)
Parts Used:
12001788
Belt wore off and broke
Opened the back panel of the washing machine. Removed the old belt and wrote down the part number. Shopped online for a suitable replacement and found a perfect match at part select.com. I put in an order and it was delivered in a couple of days! I opened the back panel of the washing machinie again. This time I decided to also replace the isolators that came with the kit. For this, I had to unscrew the motor and gently tug it free. I placed it on the floor of the washing machine. I then replaced the 2 isolators as described in the kit, reinstalled the motor and put the screw back on. I then proceeded to place the belt on the motor and on to the wheel. This took couple of tries to get the grooves right. I then tested the washing machine on a rinse cycle and things looked good. Its been working fine so far.
36 of 43 people found this instruction helpful.
Was this instruction helpful to you?
Michael from Orland Park, IL
Difficulty Level:
Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set
Parts Used:
22004465, 12001788
Loud noise when in spin dry
This kit came with instructions. I followed them closely. The only thing I could add is clean the tub spindle with steelwool to remove any debris or rust. then wipe down spindle to remove all steelwool particles and follow instructions to reassamble.
31 of 34 people found this instruction helpful.
Was this instruction helpful to you?
Douglas from Marion, IN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Parts Used:
12001788
Drive belt sqeaked and contiued to roll off the drum.
Removed washer back panel (after unplugging unit). Installed new belt. Reinstalled back panel. Belt wAs very tight getting it to roll onto the drum.
12 of 18 people found this instruction helpful.
Was this instruction helpful to you?
Glenn from San Jose, CA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set, Wrench set
Parts Used:
22002290, 12001788
Ancillary Work when Replacing Noisey Tub Bearings
The replacement for the drive belt and dispenser bezel were part of a bigger job of changing the outer tub bearings. Those familiar with Maytag Neptune washers will experience the jet-taking-off sound when the tub seals wear and water gets into the bearings. While I would have the machine open I thought I would change the drive belt. I also noticed the dispenser bezel had two of the four mounting corners broken.

Replacing the bearings was done. I purchased the bearings and rented a bearing puller made especially for this job

After the bearing and seal replacement, I put on the new belt. It was almost straight forward. Almost because the belt didn't just slip on. The new belt is much smaller than the old belt. Not having the grip strength of Mr. Atlas, I was not able to hold the belt on the pulley rim while turning the pulley around, as the instructions say. The other thing that makes this difficult is that the ribs on the outer tub are quite close to the spokes of the pulley. I was not able to firmly grasp around the belt and pulley with one hand and turn the pulley with the other. My knuckles seemed to get in the way (ouch!).

Being an electrical engineer, I happen to have cable ties handy. I used one to hold the belt on the pulley rim, and was able to turn the pulley with two hands (still watching out for my knuckles).

For the dispenser bezel, I took the old dispenser lid and hinge pins off the old bezel by cutting the bezel between the hinge points, then transferred them on the new one.

On the washer top cover, there was a lot rust around the dispenser opening. So before closing up the machine and installing the bezel, I removed the loose rust, then applied a rust converter. The rust converter was in an aerosol can, and since I was working on the washing machine inside the house and not wanting to make a mess, instead of spraying the cover, I sprayed onto a paper towel then dabbed the chemical onto the rusty spots. I finished with an appliance epoxy paint around the dispenser opening.

I'd like to say I was impressed with the service from PartSelect. I ordered on Saturday, they shipped on Monday, and the parts arrived on Tuesday morning, and this was with standard shipping. On Thursday I was ready to put on the belt, but there was also a problem where one of the motor isolators was missing from the belt kit. I called in the shortage and they shipped the next day and the new belt kit arrive on Saturday. I noticed the shipment was from Fresno so they must have a warehouse there.

So all in all, the drive belt and dispenser bezel were simple to install. Certainly they were the easiest parts of the job.
11 of 18 people found this instruction helpful.
Was this instruction helpful to you?
SHANE from NUEVO, CA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
Parts Used:
WP22002795, 12001788
Water Leaking Into Drum When Machine Is Off
Removed the front door screws & front panel screws, removed screws in the "l" brackets holding the top down, tilted the top up & back, removed 3 hoses & 3 wire connectors from the old water valve. Removed 1 screw holding valve & replaced with new valve. Re-connected 3 wires & 3 hoses, replaced top & front door. While the machine was out from the wall, removed the back loovered cover, removed the old belt & removed 1 bolt holding motor. Removed th e motor, removed & replaced the 2 plastic insolators with the new ones supplyed with the belt on the motor spindels, re-installed the motor & bolt, then the new belt that is self adjusting. Replaced back cover & put machine back online, easy deal for anyone with very basic mechanical knowledge
9 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Brandon from Berea, OH
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Parts Used:
WPY912679, WP6-912678, WP22004481, WP22004477, WP22003059, 22002290, 12001788
bad pump
I took off the rear panel and removed the hose clamps and electrical terminals, slid pump out of slot in bottom pan of washing machine. It only took minutes, this was part of a major overhaul. I replaced this as a precautionary measure. Great prices and quick service,
6 of 11 people found this instruction helpful.
Was this instruction helpful to you?
David from FOLSOM, CA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench (Adjustable)
Parts Used:
12001788
Burn smell during spin cycle.
I followed the instruction of using a tie strap to secure belt to drive pulley and turn pulley to place belt on pulley. Worked great. Done in no time.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
William from CHINA, ME
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Wrench (Adjustable)
Parts Used:
12001788
sharp metal edges
after cutting my hand I installed masking tape around the opening on the back of the washer. All went well after that
1 person found this instruction helpful.
Was this instruction helpful to you?
Customer Reviews
Average Rating:
7 Reviews
2.9
out of 5
Filter By Rating:
  • 5 Stars
    3
  • 4 Stars
    0
  • 3 Stars
    0
  • 2 Stars
    1
  • 1 Stars
    3
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Model Cross Reference

This part works with the following models:

PartSelect Number: PS2003327
Manufacturer Part Number: 12001788
Brand
Model Number
Description
Crosley
CAH4205AWJ
Washer - Residential
Crosley
CAH4205AWW
Washer - Residential
Maytag
MAH14PDAAL
Washer - Commercial
Maytag
MAH14PDAAQ
Washer
Maytag
MAH14PDAAW
Washer - Commercial
Maytag
MAH14PDABL
Washer - Commercial
Maytag
MAH14PDABW
Washer - Commercial
Maytag
MAH14PDAEW
Washer
Maytag
MAH14PDAGW
Washer
Maytag
MAH14PDBAW
Washer
Maytag
MAH14PDBEW
Washer
Maytag
MAH14PDBGW
Washer
Maytag
MAH14PDCBQ
Washer
Maytag
MAH14PDCBW
Washer
Maytag
MAH14PDDWW
Washer
Maytag
MAH14PDSAW
Washer
Maytag
MAH14PNAEW
Washer
Maytag
MAH14PNAGW
Washer
Maytag
MAH14PNAWW
Washer
Maytag
MAH14PNBAW
Washer
Maytag
MAH14PNBEW
Washer
Maytag
MAH14PNBGW
Washer
Maytag
MAH14PNSAW
Washer
Maytag
MAH14PRAWW
Washer
Maytag
MAH14PSAAW
Washer - Commercial
Maytag
MAH20PDA3W
Washer
Maytag
MAH20PDAWQ
Washer
Maytag
MAH20PDAWW
Washer - Commercial
Maytag
MAH20PDCXQ
Washer
Maytag
MAH20PDCXW
Washer