General Electric Refrigerator Hardware

Find your part

Enter your model number or a part number and click "Search"
Need help finding your model number?
General Electric Appliance Parts
Shop By Part Type

Popular General Electric Refrigerator Hardware

Videos!
Your Price
$12.89
  In Stock
Evaporator Fan Grommet - Red
★★★★★
★★★★★
19 Reviews
PartSelect Number PS963756
Manufacturer Part Number WR02X12008
If you notice that your refrigerator or freezer is noisy or too warm, you may need to replace the evaporator fan grommet. This part is red in color, and is about 1 inch in diameter. The evaporator fan grommet is located behind the evaporator fan cover in the back of the freezer. You will need to remove the evaporator fan cover to access the evaporator fan and complete this repair. Before you begin this repair, ensure the power to the refrigerator is disconnected. You will need a pair of needle nose pliers, a small flat blade screw driver and both a 1/4 and 5/16-inch nut driver to complete this repair.
Fixes these symptoms
  • Clicking sound
  • Freezer section too warm
  • Fridge too warm
  • See more...
Installation Instructions
alex from rohnert park, CA
evaporator fan making lots of noise
the repair was really easy!!! took longer to put the little clip on the fan part than it was to install the whole moter and put everthing back together

save money do it yourself..... Read more...
Videos!
Your Price
$10.73
  In Stock
Evaporator/Condensor Fan Grommet
★★★★★
★★★★★
11 Reviews
PartSelect Number PS284555
Manufacturer Part Number WR02X10098
This evaporator fan motor grommet, or condenser fan grommet is built for refrigerators. It provides a cushion between the fan motor and the motor mounting bracket. It is made or round, black plastic and is approximately one inch in diameter. If your grommet is torn or damaged and you are getting noise from the fan motor, you may need to replace it. This is an OEM part sourced directly from the manufacturer.
Fixes these symptoms
  • Clicking sound
  • Freezer section too warm
  • Fridge too warm
  • See more...
Installation Instructions
Joel from Childress, TX
Condensor fan out of service
The only part that I should had used was the condensor fan motor,which it was so easy to remove,and instaled the new one,then replaced the missing parts and problem solved. The technician before me,declare the unit a total loss,there for after doing that, he took the rest of the parts with him for his own benefit. The repair was with no difficulty,and time spend around 20 min. Thanks.PartSelect,your delivery and easy way to place an order is great. Thanks. Joel Read more...
Your Price
$12.81
  In Stock
Door Handle Fastener
★★★★★
★★★★★
7 Reviews
PartSelect Number PS6447735
Manufacturer Part Number WR01X11007
This is a door handle fastener to secure the handle to your refrigerator drawer. It is also known and a mounting bolt or screw. It is approximately 1 inch in total length, and is made of metal.
Fixes these symptoms
Installation Instructions
Charles A. from ARVADA, CO
Missing parts bought new
Very well with a print out and Allen wrench was easy Read more...
Videos!
Your Price
$10.73
  In Stock
Lid Bumper
★★★★★
★★★★★
2 Reviews
PartSelect Number PS284979
Manufacturer Part Number WR02X10540
The lid bumper or evaporator fan motor bumper in your refrigerator prevents the fan motor from scraping against the side bracket. If your refrigerator/freezer is noisy, the bumper could be worn down or missing, and the sound could be a result of the motor scraping the side bracket. You will find it between the fan motor and the side bracket on the evaporator fan motor assembly. To access the bumper, you will need to remove the evaporator fan motor assembly from the freezer. This part is made of orange rubber and is less than half an inch in diameter. It has a rounded top and a slightly pointed bottom, and is sold individually.
Fixes these symptoms
Installation Instructions
Darren from Renton, WA
Loud high pitch whining noise behind freezer
Ref. still worked but had this loud high pitch whining noise coming from inside freezer for a few months. It's probably a bad bearing or motor.

1) Remove all shelves and ice dispencer
2) Remove (x2 screws / a green wire that's clipped on) and the evap cover
3) Remove (x3 screws) cover motor/solenoid and unplug harness
3) Remove (x2 screws) icemaker and unplug harness
4) Remove/Loosen (x2 screws bottom / x2 screws top) Duct air freezer
5) Remove (x2 screws) Orifice evap fan and unplug harness
note: will need to remove right screw to get green ground wire off. And be careful on to damage the gasket.
6) Once Orifice out of refrig, disassemble.
7) Main thing to replace is the Motor DC Evap fan, and maybe CapDust, BumperLid, GrommetEvpFan.
8) now just go in reverse order...
That's it . . . wasn't too hard and NO MORE whining!!! Save at least a couple of hundred by not having a prof. come out and do it. Easy enough for most DIY person. Read more...
Your Price
$12.85
  In Stock
Mounting Screw
★★★★★
★★★★★
1 Review
PartSelect Number PS6011723
Manufacturer Part Number WR01X11014
This OEM part is from GE and is designed for use in your refrigerator. This part is known as a door mounting screw, and is for mounting the handles of the refrigerator to the door studs.
Fixes these symptoms
Your Price
$4.31
  In Stock
Screw
PartSelect Number PS11743743
Manufacturer Part Number WP681249
Sold individually.
Your Price
$6.58
  In Stock
SET SCREW
★★★★★
★★★★★
1 Review
PartSelect Number PS8767906
Manufacturer Part Number WR01X20424
Installation Instructions
Charles A. from ARVADA, CO
Missing parts bought new
Very well with a print out and Allen wrench was easy Read more...
Videos!
Your Price
$12.73
  In Stock
Push On Nut
★★★★★
★★★★★
6 Reviews
PartSelect Number PS298353
Manufacturer Part Number WR2X7054
This push on nut is for your dishwasher or refrigerator. As the name suggests, it pushes into place, rather than being screwed in. It is approximately half an inch in diameter and is made of stainless steel.
Fixes these symptoms
Installation Instructions
Joseph from Livermore, CA
Water leak from gate (diverter) valve shaft
This was a fairly simple repair. After disconnecting power to the dishwasher and removing the panel below the door, first had to remove a retainer C clip from the gate valve shaft. Then disconnected the linkage from the gate valve solenoid, removed two return springs and slid the gate valve contol arm off the shaft. Then removed the solenoid bracket that was fastened to the housing by 2 screws. This allowed access to the push on nut on the valve shaft. Removed the old push on nut which exposed the leaking seal. Removed the bad seal, then moistened and carefully slid on and seated the new drain valve shaft seal. Affixed new push on nut. Reinstalled the above mentioned parts that were removed. Problem solved - no more leak. Total cost $18.81 for factory GE parts plus $6.95 shipping. Thank you PartSelect. Read more...
Videos!
Your Price
$9.88
  In Stock
Compression Ring
★★★★★
★★★★★
2 Reviews
PartSelect Number PS1015726
Manufacturer Part Number WR02X12149
This compression ring is meant to hold the evaporator fan motor in place in the freezer compartment of your refrigerator. This is is a genuine OEM part. The tools needed to complete this repair are a Phillips screw driver and small flat blade screw driver. Be sure to turn off your refrigerator before removing the evaporator fan cover so the fan does not turn on during repair. It is recommended to check the grommets, evaporator fan, and fan blades during repair in case they also need replacning. The compression ring may need replacing if the fan is noisy, or the refrigerator compartments are too warm. This part is sold individually.
Fixes these symptoms
  • Freezer section too warm
  • Fridge too warm
  • Noisy
  • See more...
Installation Instructions
Jeffrey from Tampa, FL
My refrigerator began to overheat and the everything was thawing!!
My refrigerator began to overheat and the everything was thawing!! The condenser fan motor had seized and I thought this is something even I can replace.

I did a Google search on the refrigerator model number. The link to your site looked promising and I clicked on it. I was taken to your web page for my refrigerator and I clicked on the schematic for the condenser assembly.

The schematic had the parts I needed labeled clearly so this layman could be sure to get the right ones.

I ordered the parts at 12:45PM Monday and selected overnight shipping. The parts arrived at 8:35AM Tuesday (Thank you FedEx). I installed the parts and my refrigerator is up and running again.

To get to the condenser fan motor I took off the back panel on the fridge that covers the condenser, fan and coil. The fan/motor assembly is attached to a bracket I removed with two screws. Pulled the bracket assembly out of the back of the fridge, removed the fan blade and then the motor, and put the new motor on the bracket and stuck the new fan blade on the motor spindle. The trickiest part was getting the complete assembly back in. Just went slowly and took my time. Reconnected the wires, no problems. I took pictures of everything that I disassembled BEFORE I disassembled it in case I wasn't sure how something went back in but this job was so simple I didn't need the pictures.

I’m not sure how I could improve on this except maybe you could ship a refrigerator technician, too, to do the install.

Thank you PartSelect everything worked out better than I could have hoped and I saved $220.00 compared to what a repair service was quoting. Read more...
Your Price
$12.85
  In Stock
French Spring Pin
★★★★★
★★★★★
3 Reviews
PartSelect Number PS2322786
Manufacturer Part Number WR02X12651
This is a replacement spring pin for French door-style refrigerators. This part is made of white plastic and is approximately ½ an inch in length. If the mullion that keeps the doors closed is not working, and your door won’t stay closed, you may have a problem with the spring or the spring pin. This part is sold individually, so be sure to determine whether you need a new spring pin or the spring itself. This is an OEM part sourced directly from the manufacturer.
Fixes these symptoms
Installation Instructions
Barbara from TREMONT, IL
The French swing part of the door would not go back where it needed to. I had to put it back in place with my hand.
I just replaced the broken spring and the little plastic cylinder that goes over the end of one part of the spring. I placed the plastic part on first and slid it in place, then had to bed the other end of the spring a little bit to place it in the hole. But once it went in, the door worked perfectly. And I'm a 70 yr old woman. So if I can do it, anyone can. Read more...

Related Parts

Back to Top