EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

Kenmore Refrigerator Switches

Popular Kenmore Refrigerator Switches

The refrigerator light and fan circuit uses this three-terminal rocker arm switch. It is an OEM replacement part. Disconnect power before working on this electrical part.
The refrigerator light and fan circuit uses this three-terminal rocker arm switch. It is an OEM replacement part. Disconnect power before working on this electrical part.
What this part fixes:
  • Ice maker not making ice
  • Ice maker won’t dispense ice
  • Light not working
Installation Instructions
Kevin from Beckley, WV
while closing the door, the light switch fouled, resulting in the switch breaking
I used a flat screwdriver and released the lock tab on the bottom of the light switch, and pried the switch out, being careful to not damage the plastic around the mounting place of the switch, unplugged wiring from old switch, plugged in the new one and pushed the new switch into place. Job finished light switch now working.
If your refrigerators interior light is not working, the door switch may be the cause. It turns the light off when the door closes. This is an OEM part. Confirm compatibility using your refrigerators model number.
If your refrigerators interior light is not working, the door switch may be the cause. It turns the light off when the door closes. This is an OEM part. Confirm compatibility using your refrigerators model number.
What this part fixes:
  • Fridge too warm
  • Light not working
Installation Instructions
Clint from Rayville, MO
Lights inside refrigerator not working
I used a flat-head screwdriver to pop out the old light rocker switch. Then, I unplugged the wires, plugged them into the new light rocker switch, and then popped the new switch into the hole. That's it! Lights began working again.
An interior light that stays off or remains on after the refrigerator door closes can point to a faulty door light switch. The white OEM switch controls the light as the door opens and closes.
An interior light that stays off or remains on after the refrigerator door closes can point to a faulty door light switch. The white OEM switch controls the light as the door opens and closes.
What this part fixes:
  • Fridge too warm
  • Light not working
Installation Instructions
Lorinda from Dallas, TX
dropped something on the light switch and it broke off
we just pried out the old switch and pulled it out the rest of the way with a pair of needle nose pliers. Pulled off the wires on the broken switch and reattached to the new one and just slid/clicked it back into the hole.
The interior light of your refrigerator is controlled by a switch that is activated when the door is opened and closed. If your refrigerator light will not turn on, there could be an issue with the switch. The switch is spring loaded and is a generally closed type of switch meaning there should be no continuity when the button is depressed, and continuity through the switch when the button is not depressed. This plastic, white, OEM switch is sourced directly from the manufacturer, is sold individually and is easy to replace. The repair usually takes less than 15 minutes and requires a flat blade screwdriver and needle nose pliers.
The interior light of your refrigerator is controlled by a switch that is activated when the door is opened and closed. If your refrigerator light will not turn on, there could be an issue with the switch. The switch is spring loaded and is a generally closed type of switch meaning there should be no continuity when the button is depressed, and continuity through the switch when the button is not depressed. This plastic, white, OEM switch is sourced directly from the manufacturer, is sold individually and is easy to replace. The repair usually takes less than 15 minutes and requires a flat blade screwdriver and needle nose pliers.
What this part fixes:
  • Fridge too warm
  • Light not working
Installation Instructions
Jonathan from Lilburn, GA
Sticking Light Switch
I applied some tips learned by reading other reviews. So before I started I grabbed my trusty vise grip pliers and a small screw driver. I locked onto the switch actuator, the part that the refrigerator door pushes in, with the vise grips and pulled on it just hard enough to get the screw driver inserted in the right side to push in the catch clip so the switch could be pulled out further each time the catch clip was depressed to the next detent. Then I used the screw driver on the left site to encourage the switch past the detents on the left and very quickly the switch was out of the mount. The wires from the refrigerator pulled out with the old switch. I unplugged the old switch from the wires and plugged in the new switch and shoved the new switch back into the mount, wiggled it a couple of times to make sure it was secure and the job was done. Once I applied the vise gripes at first, the whole job took less than a minute.
This ice dispenser solenoid moves the linkage that opens the ice chute door when dispensing is activated. When power is released, the mechanism allows the flap to close and limit warm air entering the freezer. A failed or sticking solenoid may prevent ice from dispensing or leave the chute door open, contributing to frost or moisture buildup. Inspect the solenoid, spring, and door linkage before replacement, since other mechanism faults can cause similar symptoms. Disconnect power before accessing the dispenser assembly and follow the appliance instructions for mounting and wiring. This is an OEM part sourced directly from the manufacturer.
This ice dispenser solenoid moves the linkage that opens the ice chute door when dispensing is activated. When power is released, the mechanism allows the flap to close and limit warm air entering the freezer. A failed or sticking solenoid may prevent ice from dispensing or leave the chute door open, contributing to frost or moisture buildup. Inspect the solenoid, spring, and door linkage before replacement, since other mechanism faults can cause similar symptoms. Disconnect power before accessing the dispenser assembly and follow the appliance instructions for mounting and wiring. This is an OEM part sourced directly from the manufacturer.
What this part fixes:
  • Door Sweating
  • Door won’t open or close
  • Freezer not defrosting
Installation Instructions
Bill from Cleveland Heights, OH
flap to ice dispenser would not close
The flap to the ice dispenser would not close, which allowed the ice dispenser to frost up, freezing the water dispenser.

This was a simple fix. The solenoid had stopped working, so it would not automatically close the door flap. I read some posts on this site that suggest that you had to remove the trim around the entire dispenser to get at the solenoid. My fridge may be a newer model, but in any event it was much easier than that. Just below the touch pad for choosing water, ice, or crushed ice (above where the ice/water dispenses) there are three very small holes spaced about an inch a part. After unplugging the fridge, I stuck a small philips-head screw driver in each, freeing spring clips. That allowed the touch pad to come off. I then removed four screws to remove a plastic piece covering the chute, giving me access to the flap and solenoid. I just unplugged the solenoid from the circuit board on the back of the touch pad and then removed three screws to remove the old solenoid. I replaced it with the new solenoid and plugged it into the circuit board. The touch pad then snapped back into place.

The hardest part was figuring out how to get at the solenoid. After I found that pushing the clips in those three holes allowed me to remove the touch pad, it could not be any easier.
Original Equipment Manufacturer

MAKE THIS REPAIR A GUARANTEED WIN

OVER 2 MILLION PARTS TO ENSURE VICTORY

Opening the refrigerator door releases this push-button switch to turn on the interior light, making stored food easier to see. When the door closes, it presses the button and turns the light off. A stuck, worn, or broken switch may leave the light off when the door is open or keep it on after closing. Replacing a faulty switch helps restore normal lighting control and reliable response to door movement. Disconnect the refrigerator from power before removing or installing the switch. This is an OEM part sourced directly from the manufacturer.
Opening the refrigerator door releases this push-button switch to turn on the interior light, making stored food easier to see. When the door closes, it presses the button and turns the light off. A stuck, worn, or broken switch may leave the light off when the door is open or keep it on after closing. Replacing a faulty switch helps restore normal lighting control and reliable response to door movement. Disconnect the refrigerator from power before removing or installing the switch. This is an OEM part sourced directly from the manufacturer.
What this part fixes:
  • Light not working
Installation Instructions
Debbie from Waltham, MA
Remove and replace light switch
Video makes it look easy. Kenmore refrigerator does not have "groove" along the right hand side of switch that allows for pushing down on release. Used a thin screwdriver to get under to push while holding switch edge with pliers. Kept slipping. Tape sides to avoid scratching inside of refrigerator.
If your refrigerators interior light does not work, the door switch may be involved. This OEM, two-terminal switch responds to the door opening and closing to control the light and provide door-status control. Confirm it fits your refrigerator before ordering.
If your refrigerators interior light does not work, the door switch may be involved. This OEM, two-terminal switch responds to the door opening and closing to control the light and provide door-status control. Confirm it fits your refrigerator before ordering.
What this part fixes:
  • Light not working
Installation Instructions
Stephen from LOVELAND, OH
Light switch lever broke
Unplug refrigerator.
Pry switch out with putty knife
Remove two wires from switch
Attach wires to new switch
Push new switch into slot
This includes both the run capacitor and the start relay. The capacitor helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer. The start relay boosts the compressor, and then shuts off as soon as the motor gets up to speed and the overload provides extra protection against excessive temperatures.
This includes both the run capacitor and the start relay. The capacitor helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer. The start relay boosts the compressor, and then shuts off as soon as the motor gets up to speed and the overload provides extra protection against excessive temperatures.
What this part fixes:
  • Clicking sound
  • Freezer section too warm
  • Fridge and Freezer are too warm
Installation Instructions
Gilbert from Clinton, MO
The compressor would not run.
I removed the screws in the lower back panel where the compressor is located. Then I unplugged the capacitor and plugged the new one in. I then checked to see if the compressor would start. It wouldn't so I replaced the overload relay with capacitor and that fixed the problem. The capacitor just plugs into the relay then plugs into the compressor. There are several screws but all in all it is easy.
This part turns the light on/off as the door opens and closes.
This part turns the light on/off as the door opens and closes.
What this part fixes:
  • Light not working
  • Noisy
This refrigerator dispenser micro switch signals the appliance to release ice or water when you press the dispenser paddle. It responds to paddle movement, completing the electrical circuit while pressed and releasing it when your cup is removed. Worn contacts or a sticking mechanism may cause intermittent dispensing, no response, or dispensing that fails to stop normally. Replacing a faulty switch helps restore reliable paddle control. Unplug the refrigerator before opening the dispenser housing or disconnecting wiring, and handle the wire terminals carefully during replacement. This is an OEM part sourced directly from the manufacturer.
This refrigerator dispenser micro switch signals the appliance to release ice or water when you press the dispenser paddle. It responds to paddle movement, completing the electrical circuit while pressed and releasing it when your cup is removed. Worn contacts or a sticking mechanism may cause intermittent dispensing, no response, or dispensing that fails to stop normally. Replacing a faulty switch helps restore reliable paddle control. Unplug the refrigerator before opening the dispenser housing or disconnecting wiring, and handle the wire terminals carefully during replacement. This is an OEM part sourced directly from the manufacturer.
What this part fixes:
  • Ice maker not making ice
  • Ice maker won’t dispense ice
  • Leaking
Installation Instructions
BILL from BATESVILLE, MS
Front Door Ice Wouldn't Work And Air Going Into Freezer
Thanks to the pictorial diagram, I was able to order correct parts. It was just a matter of removal of broken parts and replacing them. Ice maker now working and air is no longer getting into freezer which was freezing up ice maker. Thanks for timely delivery, now I am able to use ice dispenser, which I haven't used for long time. Thanks

More Kenmore Refrigerator Parts

People often need to fix these common parts