Kenmore Refrigerator Hinges

Kenmore Appliance Parts

Popular Kenmore Refrigerator Hinges

Your Price
$23.15
  In Stock
Kenmore Refrigerator Upper or Lower Mullion Hinge Pin
★★★★★
★★★★★
4 Reviews
PartSelect Number PS2358752
Manufacturer Part Number 241779401
This mullion hinge pin is a genuine OEM replacement part, measuring 1.5 inches by 1.25 inches by 0.85 inches. It is specially designed to secure the mullion in refrigerators, allowing it to pivot and ensure smooth door movement. The mullion acts as a barrier between the refrigerator and freezer to maintain the desired temperatures for each section. A damaged or loose hinge pin will result in temperature fluctuations, frost buildup along the door edges, and difficulties opening and closing the door. Therefore, it is important that you replace the pin as soon as it is no longer functioning. Note that your appliance may require two hinge pins, one near the top of the mullion and one near the bottom. Remove the mullion cover, detach the hinge pin, and install a the new one into the hinge assembly. Place the cover back on and verify that the hinge assembly is working by carefully opening and closing the refrigerator doors to check that they are moving smoothly. Each sold individually.
Fixes these symptoms
Your Price
$7.70
  In Stock
Kenmore Refrigerator Lower Door Closing Cam
★★★★★
★★★★★
87 Reviews
PartSelect Number PS11739042
Manufacturer Part Number WP2182179
The lower door closing cam is used in refrigerator doors, it can be located on the fresh food side or the freezer side. It helps hold the door open. This cam is made out of plastic, so it might crack or wear down over time. If your door will not open and close properly you may need to replace the door closing cam. To successfully install this part, you will need a 5/16 nut driver and a small flat blade screwdriver. Before you begin, unplug your appliance and disconnect the water supply. Lubricating this part may help with installation. This replacement part is sold individually. This part will fit both the left and right side of your refrigerator door. To make the repair, remove the top hinge cover, then the top hinge support. Lift the door from the bottom support and remove the old door cams. Replace the cams, using a little lubricant if necessary, and place the door back on the lower hinge support. Replace the top hinge support and your repair is complete!
Fixes these symptoms
  • Clicking sound
  • Door Sweating
  • Door won’t open or close
  • See more...
Installation Instructions
Norbert from Sugar Land, TX
Refigerator door was not closing all the way if not pushed shut.
Remove the top hinge cover. Removed the top hinge support. Lifted the door from the bottom support. Old door cams were worn completly flat. Replaced the lower door cam and closing cam use a little vasalene for lubricant on the cam surfaces. Placed the door back on the lower hinge support. Replaced the top hinge support. Door is closing great now.
Thanks for the quick part deliver.
Read more...
Your Price
$10.55
  In Stock
Kenmore Refrigerator Door Cam - Black
★★★★★
★★★★★
64 Reviews
PartSelect Number PS11752991
Manufacturer Part Number WPW10329686
The Door Cam is a black plastic part which helps the door pivot shut while keeping the door and hinge in proper alignment. Lubricating this part upon installation may help it move easier. It attaches onto the door hinge and should be replaced if broken or if there is noticeable damage. Refer to your model number and user manual to ensure this is the correct part for you. To do this repair you will need a 5/6 nut driver, a 5/16 socket, and a ratchet. For safety purposes, do not forget to turn off your appliance before making this repair. Note that this piece is black, and as per the manufacturer requires a new screw to mount the door cam which is sold individually. Please also note that this is the closing cam for the lower door, and the upper door cam is sold as a separate kit.
Fixes these symptoms
  • Clicking sound
  • Door Sweating
  • Door won’t open or close
  • See more...
Installation Instructions
Norbert from Sugar Land, TX
Refigerator door was not closing all the way if not pushed shut.
Remove the top hinge cover. Removed the top hinge support. Lifted the door from the bottom support. Old door cams were worn completly flat. Replaced the lower door cam and closing cam use a little vasalene for lubricant on the cam surfaces. Placed the door back on the lower hinge support. Replaced the top hinge support. Door is closing great now.
Thanks for the quick part deliver.
Read more...
Your Price
$8.00
  In Stock
Kenmore Refrigerator CAM-DOOR
★★★★★
★★★★★
2 Reviews
PartSelect Number PS11755285
Manufacturer Part Number WPW10470155
Fixes these symptoms
  • Clicking sound
  • Door won’t open or close
  • See more...
Installation Instructions
William from OREFIELD, PA
Right door lower hinge assembly was damaged, such that the door sagged and would not open or close properly.
Unfortunately, I have still not managed to complete the repair, using the two parts indicated above, nor with the door bracket (part no WP2183805) that I ordered subsequently that arrived two days ago. It is not the same as, nor functionally equivalent to, the old bracket that I assumed was broken, since it was not retaining the piece in the base of the door into which the cam is inserted to mount the door. The new Cam is the correct part, but is not the solution since the old Cam is slightly worn but not damaged, and the thimble I bought does not seem to fit anywhere. The hole in the new bracket has a much too small hole to retain the Cam receptacle piece in place in the base of the door. However, this is the only lower door bracket shown in the PartSelect diagram of all the door parts used on a Whirlpool WRF560SMYM04 refrigerator. I do observe that the dark gray plastic cover on the base of the door is broken, but I don't imagine this plastic cover served to retain the Cam receptacle piece solidly in place, and this plastic cover is not offered as a replacement part either. At present I am at a total loss for how to proceed! However, the instructions for removing and replacing the door are clear and very easily carried out, and the job would be very quick and easy with the right parts. So beware if you are repairing the door on this model that the door parts diagram might not show all the parts to cover the door variations that apparently have been used! Read more...
Your Price
$17.25
  In Stock
Kenmore Refrigerator Hinge Bearing
★★★★★
★★★★★
58 Reviews
PartSelect Number PS976452
Manufacturer Part Number 240328203
Sold individually.
Fixes these symptoms
  • Clicking sound
  • Door Sweating
  • Door won’t open or close
  • See more...
Installation Instructions
Charles from Cypress, TX
Door was making a popping sound when opened and closed
Unscrewd the top hinge cove and removed two bolts from the hinge, lifted door off of the bottom hinge and laid the whole door on the floor using a beach towel to protect it from scratches. Unbolted the bottom hinge plate, replaced it with the new one. Then pulled out the old hinge bearing and replaced with a new one. Installed the door back on the bottom hinge while the magnet on the door strip held it place and rebolted the the upper hinge and reinstalled the hinge cover. All done in less than 10 minutes. No more popping sounds when I open and close the door! Read more...
Your Price
$13.55
  In Stock
Kenmore Refrigerator Door Stopper
★★★★★
★★★★★
5 Reviews
PartSelect Number PS3523083
Manufacturer Part Number 4620JJ2009A
The door stop, or door stopper, is used in refrigerators. This door stop helps keep the door in position and in balance. This part is attached to the bottom of the door and it keeps it from opening and hitting the side of the refrigerator cabinet. If you find your door hits and scratches your lower cabinet when you open your fridge door, installing this part can be a solution to this problem. Make sure to unplug your appliance from the power source before installing this part and safely store food to prevent it from deteriorating. Refer to the diagram provided by the manufacturer for further instruction.
Fixes these symptoms
Your Price
$7.28
  In Stock
Kenmore Refrigerator Hinge Bearing
★★★★★
★★★★★
1 Review
PartSelect Number PS11770609
Manufacturer Part Number 5304507147
This door hinge bushing, or hinge bearing, is a genuine OEM replacement part for your refrigerator. The hinge bearing helps the refrigerator door stay on track when opening and closing, ensuring it is flush with the cabinet when closed. You will need a screwdriver and a ratchet in order to complete this repair.
Fixes these symptoms
Installation Instructions
Benjamin from Jersey City, NJ
The refrigerator door did not come for the opening swing to be reversed
I ordered four bearing hinges and drill holes for the hinges on top and bottom of frezer and fridge doors insert the bearing hinges on the holes and all the other part on the door were able to reversed. Read more...
Your Price
$10.72
  In Stock
Kenmore Refrigerator Hinge Bracket
★★★★★
★★★★★
5 Reviews
PartSelect Number PS11739061
Manufacturer Part Number WP2183805
This hinge bracket, also known as a door stop, is attached to the bottom of the door and is used to limit how far the door swings out to protect the refrigerator itself, and any surrounding cabinets from potential damage. If your fridge is having issues opening or staying closed, check the hinges for any damage or cracking. To replace this bracket, simply remove the door off your refrigerator, unscrew and remove this bracket from the bottom of the door, and install the new one. This hinge bracket is an OEM replacement and is compatible with several different makes and models of refrigerator.
Fixes these symptoms
  • Clicking sound
  • Door won’t open or close
  • See more...
Installation Instructions
Gregory J from CHICAGO, IL
Right side door doesn't lift when closing
I failed to repair the problem and sent the parts back. The hinge bracket that I needed was WPW10524049. The hinge that I purchased was WP2183805. I gave up on trying to repair the door because it was not clear to me how to assemble the cam and hinge. There doesn't seem to be any obvious way to disassemble the hinge and cam that I have - which would allow me to replace the cam in the existing hinge. Read more...
Your Price
$7.28
  In Stock
Kenmore Refrigerator Hinge Bearing
★★★★★
★★★★★
4 Reviews
PartSelect Number PS11770608
Manufacturer Part Number 5304507146
This is a replacement hinge bearing for your refrigerator. The hinge bearing is found on the door hinge, and reduces friction when the door opens and closes. If the bearing is damaged, you may not be able to open or close the door properly, and in this case, it will need to be replaced. It is made of white plastic and is approximately 2 inches long and 1 inch in diameter. This part is sold individually and is a genuine OEM part.
Fixes these symptoms
Installation Instructions
amy from SOMERVILLE, MA
Door sagging, creating a gap to let in condensation
You tube is my best friend for DIY repair. I supported the door with wood blocks, removed the bottom bracket and was able to slide the refrigerator door down and out without removing the freezer door. Replaced both hinge bearings and door stop and washer on bottom hinge and slid the door back into place. Door is very light when empty. Fast and easy, door opens and closes smoothly and no problem with condensation anymore. Read more...
Your Price
$14.52
  In Stock
Kenmore Refrigerator Hinge Bearing
★★★★★
★★★★★
28 Reviews
PartSelect Number PS429803
Manufacturer Part Number 240328201
Sold individually. Also known as a short door closing cam.
Fixes these symptoms
  • Clicking sound
  • Door Sweating
  • Door won’t open or close
  • See more...
Installation Instructions
Al from Shakopee, MN
The ice dispenser would only dispense crushed ice, Fridge door cluncked when opening and closing
For the ice dispenser, I read a blog that pointed me right to the solenoid that controls the linkage for the crushed /cubed ice.I first unplugged the fridge. Then removed the ice maker basket. Removed 2 ea screws from each side of the supports of the lower brackets. Then lifted the tray assy off the mounting bracket, moving the front of the bracket down you can then unhook the power/control connector.
The tray then comes right out. Once out you remove two screws that hold a plastic plate on. With this removed you can see the solenoid that actuates the linkage for the ice cube and crushed ice. You then remove 2 ea machine screws that hold the solenoid in. Remove grd. wire. and pull power wires off tabs. You can then remove the solenoid by sliding it out of the plastic retainer. With it out you install the new plunger and reassemble in the reverse order. 15 mins tops.

The main Refidgerator door, made a cluncking sound. Lube didn't help. I removed the door by removing the top screw from the plastic cover, then slide it forward, then remove the two screws that hold the hinge on and then lifting the door off, once off the lower nylon hinge bearing comes right out of the door, the plate is removed with a screw driver. Installed in reverse order and cluncking was gone. 10 mins
Read more...

Related Kenmore Refrigerator Parts