Kenmore Refrigerator Doors
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Kenmore Refrigerator Doors
Your Price
$75.48
In Stock
Kenmore Refrigerator Dairy Door - Clear
PartSelect Number PS1525960
Manufacturer Part Number 240337712
This is a dairy door for your refrigerator. This part covers the products in the dairy bin section. To access this section, simply lift the lid. This dairy door is made entirely of plastic and is transparent. It is almost 10 inches wide, and roughly 6 inches long. In order to make this repair you will not need any tools, as this part will easily clip in and out of place of the hinged holes.
Installation Instructions
David from Crystal River, FL
Broken or missing retainer bars I butter dish
Took the old ones off and installed the new ones. Simple repair
Read more...
Your Price
$39.00
In Stock
Kenmore Refrigerator Dairy Door
Snapped new ones on.
Was initially intimidated, but only took 5 minutes to replace both. Read more...
PartSelect Number PS429785
Manufacturer Part Number 240326203
Installation Instructions
Rosemarie from Anchorage, AK
Trim Handles Broken during moving
Used a paint spatula to pop upwards the old bottom half of the door handle trim, has metal inserts inbetween pieces.Snapped new ones on.
Was initially intimidated, but only took 5 minutes to replace both. Read more...
Your Price
$58.34
In Stock
Kenmore Refrigerator Complete Dairy Compartment Door - Clear
PartSelect Number PS11739923
Manufacturer Part Number WP2256101
This is a replacement dairy compartment door for your refrigerator. The dairy compartment door opens and closes to allow access to the dairy items stored in the refrigerator door. Because it is made of clear plastic, the door can occasionally become cracked and broken. When the door is cracked, it will need to be replaced. The door measures approximately 15 inches in length and 6 inches in width. To replace the door, carefully remove the old door and insert the new door, lipped edge down. This product is sold individually and is OEM part from the manufacturer.
Installation Instructions
Patricia from Inglewood, CA
Both parts were broken and required replacement.
The broken part was removed and new part installed without any trouble.
Read more...
Your Price
$11.10
In Stock
Kenmore Refrigerator Pivot Block
PartSelect Number PS11743531
Manufacturer Part Number WP67003405
This is a replacement pivot block for your refrigerator. It is made of white plastic and is approximately 4 inches long and 1 inch wide. The pivot block catches and holds the door mullion cover when you close the door. If your refrigerator door will not close properly, you may need to replace the pivot block. This part is sold individually and is an OEM part sourced directly from the manufacturer.
Fixes these symptoms
- Door won’t open or close
- See more...
Installation Instructions
Elijah from Killeen, TX
I had several broken appilances broken with parts to be replaced.
I had ordered the parts from Part Select and came with in a week. I ahd a Whrilpool microwave that had a door panel and vent grille that needed to be replaced and that was rplced with ease took less that five minutes to do. My Maytag refridgerator had it kickplate grille replace along with the pivot block that took all of about two minutes. The longest job that took about 5 minutes was my Whirlpool glass oven door that needed to be replaced, but that was pretty ease to replace also with an extra hand from my son. I just didn't want to break another glass door or I would have done it myself plus I was teaching him how to do self reparts.
Read more...
Your Price
$166.78
In Stock
Kenmore Refrigerator Vertical Mullion Rail - Black
PartSelect Number PS11738596
Manufacturer Part Number WP12722803B
Commonly referred to as the flapper assembly, the door mullion is an important part of a double, or triple door refrigerator.
Fixes these symptoms
- Door won’t open or close
- See more...
Installation Instructions
Don from Alpine, TX
Broken Rail-Mullin
The mullin requires only one screw removal, then LIFT the entire mullin upwards. Pop the wire harness loose, and replace with new mullin. Simple job,
Read more...
Your Price
$25.45
In Stock
Kenmore Refrigerator Door Closing Cam
One false start because I did not realize both of the door-closing cams had disintegrated and I had only ordered the cam without the hinge.
Purchased part 290199 Hinge Assembly. It came with matching door-closing cam. (Had not known so I also purchased the cam 297995 separately). Next time I will know to only purchase the Hinge Assembly.
Replacement procedure took about 20 minutes including removing and replacing door shelves and their contents. Two people involved.
1. Remove all door shelves with contents and other contents on door.
2. Remove the top Phillips head screw holding the decorative plastic on the top.
3. Remove the two top hinge screws on top of refrigerator using metric #8 socket wrench. Second person made sure door did not fall off.
4. Lift the door off the bottom hinge pin. Second person holds door on it’s side.
5. Take off the bottom refrigerator cover
6. Remove the bottom hinge assembly screws using metric #8 socket wrench.
7. Mount the replacement bottom hinge assembly and tighten the two screws.
8. On the door bottom, remove the outer screw and loosen the inner screw using metric #8 socket wrench.
9. Replace the door-closing cam (or what is left of it) with the cam in line with the door and cam bumps away from the door.
10. Place the door back on the hinge pin (one person holds while the other person maneuvers the door bottom).
11. Replace the top hinge and reinsert the screws on top of the refrigerator. Dress the door so that it does not press hard on the rubber door gaskets (or the door will fail to shut automatically). Tighten the screws.
12. Replace the decorative plastic over the top hinge.
13. Open the door and replace the bottom refrigerator cover.
14. Replace the door shelves and all contents.
15 Close the door. Read more...
PartSelect Number PS297995
Manufacturer Part Number WR2X4901
This single door closure cam is mounted on the door, not the hinge.
Fixes these symptoms
- Clicking sound
- Door Sweating
- Door won’t open or close
- See more...
Installation Instructions
Gary from North eastham, AL
Door would not automatically close.
Symptom: Door did not close automatically. Also had found small chunks of black plastic on the floor. Refrigerator door was slightly lower than the freezer door.One false start because I did not realize both of the door-closing cams had disintegrated and I had only ordered the cam without the hinge.
Purchased part 290199 Hinge Assembly. It came with matching door-closing cam. (Had not known so I also purchased the cam 297995 separately). Next time I will know to only purchase the Hinge Assembly.
Replacement procedure took about 20 minutes including removing and replacing door shelves and their contents. Two people involved.
1. Remove all door shelves with contents and other contents on door.
2. Remove the top Phillips head screw holding the decorative plastic on the top.
3. Remove the two top hinge screws on top of refrigerator using metric #8 socket wrench. Second person made sure door did not fall off.
4. Lift the door off the bottom hinge pin. Second person holds door on it’s side.
5. Take off the bottom refrigerator cover
6. Remove the bottom hinge assembly screws using metric #8 socket wrench.
7. Mount the replacement bottom hinge assembly and tighten the two screws.
8. On the door bottom, remove the outer screw and loosen the inner screw using metric #8 socket wrench.
9. Replace the door-closing cam (or what is left of it) with the cam in line with the door and cam bumps away from the door.
10. Place the door back on the hinge pin (one person holds while the other person maneuvers the door bottom).
11. Replace the top hinge and reinsert the screws on top of the refrigerator. Dress the door so that it does not press hard on the rubber door gaskets (or the door will fail to shut automatically). Tighten the screws.
12. Replace the decorative plastic over the top hinge.
13. Open the door and replace the bottom refrigerator cover.
14. Replace the door shelves and all contents.
15 Close the door. Read more...
Your Price
$22.26
In Stock
Kenmore Refrigerator Door Shelf Retainer Bar End Cap
PartSelect Number PS299579
Manufacturer Part Number WR2X9162
This is a replacement shelf bar end cap. The end cap connects to the shelf bar on either side, and then snaps into position on the freezer door. This will allow you to store items in the freezer door. It is a little more than 2 inches long and is made of white plastic. To replace the end cap, you can simply depress the locking tab and remove the entire bar and end cap assembly. Then, use a flat blade screwdriver to depress the locking tab, and the endcap will detach. Finally, snap the new end cap locking tabs into place, and snap the bar assembly back onto the freezer door. This product is sold individually.
Installation Instructions
Bushnell from Gulf Shores, AL
Your Price
$11.10
In Stock
Kenmore Refrigerator Door Closure Cam Kit
(Not after as I did. The second time you do any of these repairs go SO much better :o)
After putting the door back on, adjust the tension of the screws holding the door in place if needed to align the door on the cams so that it shuts completely. Failure to do this will require taking the top off the door again. (see comment above on "... second time...")
If all is properly aligned, the door should swing completely shut.
Even with the mistakes that required removing the door to lubricate the cams, and removing it AGAIN to readjust the screws on the top to properly align the door on the cams, this was a twenty minute job. My wife and I were still speaking to one another at the end of it- a sure sign of an easy repair. Read more...
PartSelect Number PS2168612
Manufacturer Part Number R0181181
This door closing cam kit is intended for use on the bottom of your refrigerator and freezer door hinges. The cam helps close the doors and to lifts them slightly when opened. If your door will not open or close, or will not stay closed, there could be an issue with the door close cam. Other common symptoms associated with the door close cam are: the door is sweating, the fridge is too warm, or a clicking sound can be heard coming from the door. If your refrigerator has an ice and water dispenser, you will need to disconnect the power and water to the unit before you begin the repair.
Fixes these symptoms
- Clicking sound
- Door Sweating
- Door won’t open or close
- See more...
Installation Instructions
Russ from Asheville, NC
Door would not close
After emptying the refrig. door, I unscrewed the plate on the top of the refrigerator that covered the door bolts. Then off with the three bolts. I removed the door by lifting it up a few inches. The two parts of the door cam were easily removed and replaced with the new part. BEFORE REPLACING the door spread vasoline on both cam parts. (Not after as I did. The second time you do any of these repairs go SO much better :o)
After putting the door back on, adjust the tension of the screws holding the door in place if needed to align the door on the cams so that it shuts completely. Failure to do this will require taking the top off the door again. (see comment above on "... second time...")
If all is properly aligned, the door should swing completely shut.
Even with the mistakes that required removing the door to lubricate the cams, and removing it AGAIN to readjust the screws on the top to properly align the door on the cams, this was a twenty minute job. My wife and I were still speaking to one another at the end of it- a sure sign of an easy repair. Read more...
Your Price
$181.09
In Stock
Kenmore Refrigerator Verticle Mullion Rail - Apollo Gray
- Remove the screw from the center hinged cover.
- Remove the mullion rail by pushing upward. The top and bottom hinges slide over tabs attached to the door. I had to bump it gently from underneath.
- Disconnect the three wire connector that's underneath the center hinged cover.
Install the new mullion rail by reversing the above steps:
- Connect the three wire connector and snap it into its holder.
- Slide the new part over the top and bottom hinges. Be sure that all three hinges are correctly lined up before sliding the rail over the tabs.
- Push it down far enough that the hole for the screw in the center cover is lined up with its corresponding receptacle in the door.
- Replace the screw. Read more...
PartSelect Number PS11738595
Manufacturer Part Number WP12722803AP
Fixes these symptoms
- Door won’t open or close
- See more...
Installation Instructions
Michael from FALLBROOK, CA
When right hand door was opened first, and then left hand door, the mullion rail did not move all the way to the "open" position so that if the left hand door was closed after the right hand door the rail would bang against the right hand door and not close all the way until manually pushed into pos
Remove the existing mullion rail:- Remove the screw from the center hinged cover.
- Remove the mullion rail by pushing upward. The top and bottom hinges slide over tabs attached to the door. I had to bump it gently from underneath.
- Disconnect the three wire connector that's underneath the center hinged cover.
Install the new mullion rail by reversing the above steps:
- Connect the three wire connector and snap it into its holder.
- Slide the new part over the top and bottom hinges. Be sure that all three hinges are correctly lined up before sliding the rail over the tabs.
- Push it down far enough that the hole for the screw in the center cover is lined up with its corresponding receptacle in the door.
- Replace the screw. Read more...
Your Price
$42.49
In Stock
Kenmore Refrigerator Compartment Door
PartSelect Number PS11739749
Manufacturer Part Number WP2218113
This part is the replacement compartment door for your refrigerator. It is made of clear plastic and is approximately 9 inches by 6 inches. The compartment door snaps into the walls of the dairy compartment on the refrigerator door itself and operates on a hinge so that it can open and close. The main reason to replace the compartment door is if yours is cracked, broken, or missing. To replace the compartment door, carefully remove the hinges, then attach the new door into the hinges. This part is sold individually and is an OEM part.
Installation Instructions
john from NORWOOD, MA
replaced cracked compartment door
removed old and installed new compartment door by hand.
Read more...
Related Kenmore Refrigerator Parts
- All Kenmore Refrigerator parts
- Kenmore Refrigerator Brackets and Flanges
- Kenmore Refrigerator Caps and Lids
- Kenmore Refrigerator Circuit Boards and Touch Pads
- Kenmore Refrigerator Compressors
- Kenmore Refrigerator Deflectors and Chutes
- Kenmore Refrigerator Dispensers
- Kenmore Refrigerator Door Shelves
- Kenmore Refrigerator Drawers and Glides
- Kenmore Refrigerator Drip Bowls
- Kenmore Refrigerator Ducts and Vents
- Kenmore Refrigerator Electronics
- Kenmore Refrigerator Elements and Burners
- Kenmore Refrigerator Fans and Blowers
- Kenmore Refrigerator Filters
- Kenmore Refrigerator Grates
- Kenmore Refrigerator Grilles and Kickplates
- Kenmore Refrigerator Handles
- Kenmore Refrigerator Hardware
- Kenmore Refrigerator Hinges
- Kenmore Refrigerator Hoses and Tubes
- Kenmore Refrigerator Ice Makers
- Kenmore Refrigerator Insulations
- Kenmore Refrigerator Knobs
- Kenmore Refrigerator Latches
- Kenmore Refrigerator Lights and Bulbs
- Kenmore Refrigerator Motors
- Kenmore Refrigerator Panels
- Kenmore Refrigerator Power Cords
- Kenmore Refrigerator Seals and Gaskets
- Kenmore Refrigerator Sensors
- Kenmore Refrigerator Springs and Shock Absorbers
- Kenmore Refrigerator Switches
- Kenmore Refrigerator Tanks and Containers
- Kenmore Refrigerator Thermostats
- Kenmore Refrigerator Timers
- Kenmore Refrigerator Trays and Shelves
- Kenmore Refrigerator Trims
- Kenmore Refrigerator Valves
- Kenmore Refrigerator Wheels and Rollers
- Kenmore Refrigerator Wire Plugs and Connectors
