EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

Kenmore Refrigerator Valves

Popular Kenmore Refrigerator Valves

This refrigerator water inlet valve assembly controls water flow to the ice maker and door dispenser. Its three electric coils open and close separate water paths, sending water where it is needed. A leaking or blocked valve may cause weak dispenser flow, small ice cubes, slow ice production, or water pooling behind the refrigerator. Replacing a faulty assembly helps restore steady water flow and stops unwanted filling between uses. Unplug the refrigerator and shut off the water supply before replacing the valve. This is an OEM part sourced directly from the manufacturer.
This refrigerator water inlet valve assembly controls water flow to the ice maker and door dispenser. Its three electric coils open and close separate water paths, sending water where it is needed. A leaking or blocked valve may cause weak dispenser flow, small ice cubes, slow ice production, or water pooling behind the refrigerator. Replacing a faulty assembly helps restore steady water flow and stops unwanted filling between uses. Unplug the refrigerator and shut off the water supply before replacing the valve. This is an OEM part sourced directly from the manufacturer.
What this part fixes:
  • Ice maker dispenses too little ice
  • Ice maker not making ice
  • Ice maker won’t dispense ice
Installation Instructions
Jose from Alexandria, VA
water leaking out of refrigerator
In my specific appliance the water valve is located in the bottom right hand corner looking at it from the back. To get to it I remove the thin layer of cardboard the covers the back of the fridge. I then proceeded to disconnect the 1/4" copper tubing which is the water feed coming out of the wall. Then I removed the screws that hold the valve assembly in place. I took the water valve out and removed the electrical connections as well as the plastic tubing which feed the water dispenser and the ice maker. To install the new water valve it was just a matter of reversing steps.
The water inlet valve (Refrigerator Water Inlet Valve Kit) provides water for the ice maker and water dispenser. This part is located at the back of the refrigerator, and connects to the water supply. If your water inlet valve is malfunctioning, you could be getting a lack of water to the inside of your refrigerator. Your ice maker may not produce cubes or your water dispenser may not work. This breakage can occur from material fatigue or normal use, and is a sign the part should be replaced soon. The water inlet valve must be replaced if the solenoids no longer have continuity or the valve has internal blockage. The part measures approximately 6.5 inches long and 3 inches wide and is constructed of plastic and metal. It comes in blue/green/red.
The water inlet valve (Refrigerator Water Inlet Valve Kit) provides water for the ice maker and water dispenser. This part is located at the back of the refrigerator, and connects to the water supply. If your water inlet valve is malfunctioning, you could be getting a lack of water to the inside of your refrigerator. Your ice maker may not produce cubes or your water dispenser may not work. This breakage can occur from material fatigue or normal use, and is a sign the part should be replaced soon. The water inlet valve must be replaced if the solenoids no longer have continuity or the valve has internal blockage. The part measures approximately 6.5 inches long and 3 inches wide and is constructed of plastic and metal. It comes in blue/green/red.
What this part fixes:
  • Ice maker dispenses too little ice
  • Ice maker not making ice
  • Ice maker won’t dispense ice
Installation Instructions
GLENN from ORLAND PARK, IL
was not making ice
take out ice bucket, just loosen the top 2 screws, remove the bottom screw, slide ice maker up & out, srewdriver to release wiring harness clip, reverse to put back in. was very simple. did not install water inlet kit yet. water under fridge stopped after i changed the ice maker.
If your refrigerator is leaking, the dispenser is not dispensing, or the ice maker is not making or dispensing ice, the inlet valve may be involved. It controls water flow to the refrigerators water system and includes a guard. Check water pressure first; if it is sufficient, test valve continuity with a multimeter. Disconnect power before testing or replacing the valve. The inlet uses a 1/4-inch compression fitting, with 1/4-inch and 5/16-inch John Guest outlets. Confirm fit for your refrigerator.
If your refrigerator is leaking, the dispenser is not dispensing, or the ice maker is not making or dispensing ice, the inlet valve may be involved. It controls water flow to the refrigerators water system and includes a guard. Check water pressure first; if it is sufficient, test valve continuity with a multimeter. Disconnect power before testing or replacing the valve. The inlet uses a 1/4-inch compression fitting, with 1/4-inch and 5/16-inch John Guest outlets. Confirm fit for your refrigerator.
What this part fixes:
  • Ice maker dispenses too little ice
  • Ice maker not making ice
  • Ice maker won’t dispense ice
Installation Instructions
ralph from bristow, VA
Refrigertor water dispenser not working BUT ice machine is working
The very first symptom here is important! The door water dispenser is not working but the ice macine is working. You may only have a frozen water tube in the door so do the following before diagnosing that your solenoid valve is bad: 1) the tube usually runs under the front of the refrigerator and usually has a quick disconnect. Undo the connection and press the dispenser. If water comes out of the tube you have a frozen or blocked tube in the door. 2) Immediately adjust the temperature in the freezer and warm the freezer compartment as much as you can without destroying the freezer contents. Wait 24 hours. This will usually unfreeze the line. Do not waste your time with a hair dryer. NOW, if this doesn't work and you are convinced you need to order and replace the solenoid, follow these steps. Assemble your tools first. I needed a good ratchet set and a screwdriver. A shop towel is helpful for spilled water. A light is handy. Pull out the refreigerator to gain access to the rear of the unit. Unplug the power and close the water valve (older homes, you may need to actually shut the house water supply). Remove the screws which hold the cover over the lower half of the refrigerator. On the left you will see the solenoid. It's always good to see that your new part matches the one you feel needs replaced. They may not match perfectly due to changing design but they should be very similar. One screw holds this part in place and access is very simple. Now simply unplug the electrical connections. In my case, one blue "blade" type connection (powering the water) and one red "blade" type connection powering the ice maker. They are not the same size and this coupled with the coloring means you will not accidently switch them. pull the tubes clear of the solenoid. This is simple and needs no explantion. Grab your new solenoid and reattach both the electrical and water lines (two, remember, ice maker and drink dispencer). Replace the single screw. Re-attach the rear, lower refrigerator cover and go to the front of the unit to check the water. You can listen carefully and hear the power engage from the new part bringing you water. Clean up, replace the refrigerator back to its place and look really tired when your wife sees that you worked "so hard"! You probably saved at least $50-$80 from a service call which can now be used to take the family to dinner after your "exhausting" 15 minute workout of removing about 10 screws and wheeling the unit in and out of place. Writing this article took longer! My 4 year old worked harder holding the flash light!
This part releases water from the supply line when it's activated.
This part releases water from the supply line when it's activated.
What this part fixes:
  • Ice maker not making ice
  • Ice maker won’t dispense ice
  • Leaking
Installation Instructions
Robert from STRONGSVILLE, OH
Ice maker not making cubes.
First off you need to shut off the water supply valve that goes to the icemaker. Next pull the refrigerator from the wall , thats the fun part. I did not unplug my refrigerator when I did this . You can to be extra safe. At the bottom on the back side remove the cardboard cover on the bottom like four or five screws and set this aside. The water valve is on the bottom on the right side. There are 3 water lines attached to it. Having a towel handy might be helpfull. 1 line supplys the water, 1 is for the water dispenser and 1 is for the ice maker. These are push in connections no wrench needed. Remove the 2 screws that attach water valve to frame. Arrange it to make removing the 2 wire connections and water lines easier to remove. Wire connections just pull off. Mark them as to what valve they go to. Next remove the water lines. you need to remove a plastic lock that insures that the water lines do not pop off, very simple. Next push down on the nylon connector push down on the top of connector and pull on the plastic water line at the same time and it will come out. Do this to all 3 water lines. Remove old water valve and install new one in the reverse order. The water lines just push in no need to mess with connector when line is in reinsert the plastic lock. Reconnect the power connections. Align the water valve bracket with screw holes in frame and reattach the 2 screws holding it in place. Now would be a good time to turn on the water and check for leaks. You can check water dipenser but ice maker has a mind of its own. If all is good reinstall the cardboard cover on the back bottom and push refrigerator back where it was. Make sure the water line is not kinked. Aftre a couple of hours the ice maker should start making ice.
This refrigerator water inlet valve controls the flow of household water into the ice maker or water dispenser. It opens when water is needed and closes to stop the flow. A worn or damaged valve may cause slow filling, reduced ice production, dripping, or leaks near the back of the refrigerator. Replacing a faulty valve helps restore proper water flow and keeps the supply shut off between uses. Unplug the refrigerator and turn off the water supply before starting the repair. This is an OEM part sourced directly from the manufacturer.
This refrigerator water inlet valve controls the flow of household water into the ice maker or water dispenser. It opens when water is needed and closes to stop the flow. A worn or damaged valve may cause slow filling, reduced ice production, dripping, or leaks near the back of the refrigerator. Replacing a faulty valve helps restore proper water flow and keeps the supply shut off between uses. Unplug the refrigerator and turn off the water supply before starting the repair. This is an OEM part sourced directly from the manufacturer.
What this part fixes:
  • Ice maker not making ice
  • Ice maker won’t dispense ice
  • Leaking
Installation Instructions
Orville from Garland, TX
Was not filling the ice tray full.
I had put in a new ice maker and it still had the problem, (I needed the Ice maker anyway) I installed the vale and while I was at it I put a five year filter on the water line that went from the value to the Ice maker, it took less than one hours, the ice is making like it did when it was new, I could not be more please at theis time. Thanks for your Interest. God bless.
Original Equipment Manufacturer

MAKE THIS REPAIR A GUARANTEED WIN

OVER 2 MILLION PARTS TO ENSURE VICTORY

This refrigerator primary water inlet valve controls water entering the appliance from the household supply line. Its electric coil opens the valve when water is needed and closes it to stop the flow between uses. A worn or blocked valve may cause slow dispenser flow, reduced ice production, unwanted dripping, or leaks near the valve housing. Replacing a faulty valve helps restore controlled water delivery and proper shutoff. Unplug the refrigerator and turn off its water supply before disconnecting tubing or electrical wiring. This is an OEM part sourced directly from the manufacturer.
This refrigerator primary water inlet valve controls water entering the appliance from the household supply line. Its electric coil opens the valve when water is needed and closes it to stop the flow between uses. A worn or blocked valve may cause slow dispenser flow, reduced ice production, unwanted dripping, or leaks near the valve housing. Replacing a faulty valve helps restore controlled water delivery and proper shutoff. Unplug the refrigerator and turn off its water supply before disconnecting tubing or electrical wiring. This is an OEM part sourced directly from the manufacturer.
What this part fixes:
  • Ice maker not making ice
  • Leaking
  • Not dispensing water
Installation Instructions
Mario from Rockledge, FL
Water on the floor, fridge leak
Back cover was wet in the area of the inlet valve(sign). Water on the floor. 90% of the time is a leaking inlet valve. But it could be frozen water on the drain pan- so I exposed the radiator fins and drain pan and looked. No ice so I went to the valve and opened the copper line valve and waited a few minutes- as soon as water was called by the. Ice maker it leaked. So I went ahead and replaced the valve and after I made sure no leaks were visible I replaced the back cover and continued to observe and all was good. I treated the fridge as a new installation, changed filter and dumped the next two ice buckets. Then I proceeded to demand brownie points.
This refrigerator water inlet valve assembly controls water flow to the dispenser and ice maker through four electrically operated solenoids. It opens the required water passages when filling or dispensing is requested, then closes them to stop the flow. A cracked housing or faulty valve may cause leaks, slow dispensing, poor ice maker filling, or unwanted dripping into the ice tray. Replacing a failed assembly helps restore controlled water delivery and reliable shutoff, supporting normal ice production and everyday use of the water dispenser. This is an OEM part sourced directly from the manufacturer.
This refrigerator water inlet valve assembly controls water flow to the dispenser and ice maker through four electrically operated solenoids. It opens the required water passages when filling or dispensing is requested, then closes them to stop the flow. A cracked housing or faulty valve may cause leaks, slow dispensing, poor ice maker filling, or unwanted dripping into the ice tray. Replacing a failed assembly helps restore controlled water delivery and reliable shutoff, supporting normal ice production and everyday use of the water dispenser. This is an OEM part sourced directly from the manufacturer.
What this part fixes:
  • Ice maker not making ice
  • Ice maker won’t dispense ice
  • Leaking
Installation Instructions
Neville from LITHONIA, GA
Not making ice in both ice maker or dispensing water
To confirm my diagnosis I first replace the filter still no water flow.
Check water supply from the wall valve: ok
Remove the entire inlet valve assembly and sit it over a small bucket.
Disconnect the tubing from the bottom of the 1st selenide valve: this is the one leading to the filter.
Place cup under water dispenser and activate dispenser. No water discharge from inlet valve confirm valve is bad.
Install the new valve matching the colored tubing with the color on each inlet valve.
Re-connect the water supply place container under water dispenser and activate: There will be a large gush of air then water. Dispense aprox 1 gallon of water to confirm all the air is purged from the system. Your refrigerator is now back to dispensing water and making ice.
Good luck everyone - Neville
Leaking, no water dispensing, or an ice maker that is not making ice can be associated with the refrigerators water inlet valve. The valve supplies water to both the ice maker and dispenser, but these symptoms alone do not confirm it is faulty. This OEM valve is for select refrigerators; check fit against your refrigerators model number.
Leaking, no water dispensing, or an ice maker that is not making ice can be associated with the refrigerators water inlet valve. The valve supplies water to both the ice maker and dispenser, but these symptoms alone do not confirm it is faulty. This OEM valve is for select refrigerators; check fit against your refrigerators model number.
What this part fixes:
  • Ice maker not making ice
  • Leaking
  • Not dispensing water
Installation Instructions
Ronald from WHITESBURG, GA
water inlet valve was leaking / the Snack Pan was broked
I replaced the water inlet valve perfect match and also replaced the snack pan perfect match. I'm glad I ordered from Whirlpool. was also cheaper than other sites.. thanks.
The single water inlet valve, also known as a water solenoid valve, is used for refrigerators. This part is a solenoid-operated switch that releases water from the supply line to the water valve and into the icemaker mold when activated. If your icemaker is making small cubes, does not dispense ice or water, or leaks, this replacement could solve the issue. The tools needed for this repair are a 1/4 inch nut driver and a utility knife. Refer to the diagram provided by the manufacturer for further instructions. As a safety precaution, remember to unplug your dryer from the power source.
The single water inlet valve, also known as a water solenoid valve, is used for refrigerators. This part is a solenoid-operated switch that releases water from the supply line to the water valve and into the icemaker mold when activated. If your icemaker is making small cubes, does not dispense ice or water, or leaks, this replacement could solve the issue. The tools needed for this repair are a 1/4 inch nut driver and a utility knife. Refer to the diagram provided by the manufacturer for further instructions. As a safety precaution, remember to unplug your dryer from the power source.
What this part fixes:
  • Ice maker not making ice
  • Ice maker won’t dispense ice
  • Leaking
Installation Instructions
Robert from Abingdon, MD
No water feed to icemaker
To troubleshoot - Check water supply to valve. It f that's good - remove back plate, remove water valve reconnect inlet line, disconnect electrical connector, place valve over a pan with outlet fitting disconnected, temporarily connect 110 VAC with clipleads to water valve solenoid. No water flow means valve is not opening. To install new valve, connect outlet line, and wiring connector, then insert in cabinet and install 2 screws, reinstall back plate, connect water inlet line.
This refrigerator water inlet valve assembly controls the water supplied to the dispenser and automatic ice maker. It opens when the appliance requests water and closes when dispensing or filling ends. A cracked housing or faulty valve may cause leaks, weak dispenser flow, or prevent the ice maker mold from filling. Replacing a failed assembly helps restore controlled water delivery and proper shutoff between uses. The valve connects the incoming supply to the internal water system, supporting everyday dispensing and ice production. This is an OEM part sourced directly from the manufacturer.
This refrigerator water inlet valve assembly controls the water supplied to the dispenser and automatic ice maker. It opens when the appliance requests water and closes when dispensing or filling ends. A cracked housing or faulty valve may cause leaks, weak dispenser flow, or prevent the ice maker mold from filling. Replacing a failed assembly helps restore controlled water delivery and proper shutoff between uses. The valve connects the incoming supply to the internal water system, supporting everyday dispensing and ice production. This is an OEM part sourced directly from the manufacturer.
What this part fixes:
  • Ice maker not making ice
  • Leaking
  • Not dispensing water
Installation Instructions
Richard from JACKSONVILLE, FL
replace leaking water inlet valve assembly
1. Shut off water to refrigerator. 2. Removed bottom sheet metal cover (6 screws). 3. Removed leaking water inlet valve assembly from refrigerator (1 screw). 4. Remove water inlet tube (loosen nut) and tube back to refrigerator (pull from water valve after remove cotter pin washer). 5. Detach two electrical wire harnesses. 6. Install new water inlet valve assembly to refrigerator (1 screw). 7. Replace both water tubes to water inlet assembly. 8. Re-attach both wiring harnesses. 9. Turn water to refrigerator on. 10. Check for leaks. 11. Re-attach bottom sheet cover (6 screws).

More Kenmore Refrigerator Parts

People often need to fix these common parts