General Electric Dishwasher Pumps

Find your part

Enter your model number or a part number and click "Search"
Need help finding your model number?
General Electric Appliance Parts
Shop By Part Type

Popular General Electric Dishwasher Pumps

Your Price
$32.51
  In Stock
Drain Valve Shaft Seal
★★★★★
★★★★★
11 Reviews
PartSelect Number PS263930
Manufacturer Part Number WD8X181
The drain valve shaft seal is a part for your dishwasher drain pump valve. This seal creates a watertight closure around the flapper valve shaft. This part can be accessed through the access panel at the front for a built-in. For a portable dishwasher, consider disconnecting and unplugging the taps and lay on a blanket to access the bottom of the machine. This will need to be replaced if you notice leaking coming from the pump. This part measures approximately 3/8 inches in diameter and is black in color. This is a genuine OEM part that comes right from the manufacturer.
Fixes these symptoms
Installation Instructions
Joseph from Livermore, CA
Water leak from gate (diverter) valve shaft
This was a fairly simple repair. After disconnecting power to the dishwasher and removing the panel below the door, first had to remove a retainer C clip from the gate valve shaft. Then disconnected the linkage from the gate valve solenoid, removed two return springs and slid the gate valve contol arm off the shaft. Then removed the solenoid bracket that was fastened to the housing by 2 screws. This allowed access to the push on nut on the valve shaft. Removed the old push on nut which exposed the leaking seal. Removed the bad seal, then moistened and carefully slid on and seated the new drain valve shaft seal. Affixed new push on nut. Reinstalled the above mentioned parts that were removed. Problem solved - no more leak. Total cost $18.81 for factory GE parts plus $6.95 shipping. Thank you PartSelect. Read more...
Your Price
$120.89
  In Stock
Circulation Pump
★★★★★
★★★★★
10 Reviews
PartSelect Number PS11772000
Manufacturer Part Number WD26X23258
This part contains the Piranha clamps in kit WD35X10382
Fixes these symptoms
  • Leaking
  • Not cleaning dishes properly
  • Will Not Start
  • See more...
Installation Instructions
Bradley from NEWPORT, KY
No washing action during the wash cycle, the machine still filled and drained
The installation is fairly straightforward, basically one plug in electrical connection and two plumbing connections. The smaller of the two plumbing connections can be tricky because of the hose clamp... The original clamps are one time use crimp style. The replacements are standard hose clamps, which means the section where the tension mechanism is, is a bit wider than the clamp itself... This can cause the rubber collar on the dishwasher to slide off/separate from the pump part itself when tightening the hose clamp. If you are careful and align things just right, it will work like a charm. The best advice I have is to take your time and make sure the connections are snug without being too tight, otherwise it could leak and/or something else could break. Read more...
Your Price
$36.34
  In Stock
Sump
★★★★★
★★★★★
18 Reviews
PartSelect Number PS959014
Manufacturer Part Number WD18X10026
This works in conjunction with the pump and filtration system. It is used to receive drainage for disposal.
Fixes these symptoms
  • Leaking
  • Not cleaning dishes properly
  • Not draining
  • See more...
Installation Instructions
John from North Haven, CT
sump inlet was partially dissolved
Disconnected electrics,plumbing, and removed DW.
Replaced sump inlet by removing about four clamps.
The inlet was partially dissolved. I think what lead to this is a partial clog, of broken glass and plastic. DW works fine. Read more...
Your Price
$213.44
  In Stock
Pump and Motor Assembly
★★★★★
★★★★★
4 Reviews
PartSelect Number PS3486941
Manufacturer Part Number WD26X10051
The pump ejects the water from the unit.
Fixes these symptoms
Your Price
$29.53
  In Stock
SUMP INLET
PartSelect Number PS3505446
Manufacturer Part Number WD18X10049
Fixes these symptoms
Your Price
$55.79
  In Stock
Circulation Pump Impeller Kit
★★★★★
★★★★★
3 Reviews
PartSelect Number PS1017766
Manufacturer Part Number WD19X10038
This impeller and motor shaft seal kit is used in dishwashers to rebuild the circulation pump. If your dishwasher has any of the following symptoms, replacing the part could be the solution: circulation pump is leaking, not cleaning dishes, not draining, making loud or odd noises. The tools needed for this repair are an adjustable wrench, 1/4 inch nut driver, 5/16 inch nut driver, Phillips screwdriver, flathead screwdriver, flat file, and needle nose pliers. Remember to unplug your dishwasher before installing this part and refer to the manual provided by the manufacturer for installation instructions and a detailed diagram.
Fixes these symptoms
  • Leaking
  • Noisy
  • Not cleaning dishes properly
  • See more...
Installation Instructions
Bonnie from KILLINGTON, VT
excessively delayed delivery
I couldn't do the repair because the parts arrived a week after I left, even though I paid extra for speedy delivery. And there was ZERO customer support - the phone message said they would not answer the phone, and the email response was a generic FAQ. Read more...
Your Price
$34.56
  In Stock
Inlet Sump
★★★★★
★★★★★
7 Reviews
PartSelect Number PS259528
Manufacturer Part Number WD18X10008
This sump inlet is attached to the tub bottom and collects water for the pump in the dishwasher. The inlet works with the pump and filtration system to receive drainage for it be disposed. If there is leaking or you find your dishes are not cleaning properly, replace this part may be the solution. Remember to unplug your dishwasher from the power source as a safety precaution and refer to the manual provided by the manufacturer for further installation instructions and accurate guidance.
Fixes these symptoms
  • Leaking
  • Not cleaning dishes properly
  • Not draining
  • See more...
Installation Instructions
Ashraf from Merrick, NY
Leak from the bottom center
The connector pump had a pinhole leak at the seam (new part did not have seams). Also replaced the sump inlet which looked worn and the impeller.

Lay dishwasher on it's back to access the bottom. Loosen all clamps. Remove both U shaped holders on the sump inlet. Remove screws holding the drain motor. Pull out the pump motor and sump inlet. Connector pump can be unscrewed from the bottom.

Replace parts and reassemble. It isn't that bad once you start disassembly, especially for anyone somewhat handy. Read more...
Your Price
$37.91
  In Stock
Pump Connector
★★★★★
★★★★★
10 Reviews
PartSelect Number PS259530
Manufacturer Part Number WD18X10010
The circulation pump adapter, or pump adapter assembly connects the circulation pump to the tub of your dishwasher. If your dishwasher is leaking around this adapter, check the connection to ensure everything is fitted tightly. If there is a problem with the adapter, make sure to disconnect the water supply to your dishwasher before completing the repair.
Fixes these symptoms
Installation Instructions
Ashraf from Merrick, NY
Leak from the bottom center
The connector pump had a pinhole leak at the seam (new part did not have seams). Also replaced the sump inlet which looked worn and the impeller.

Lay dishwasher on it's back to access the bottom. Loosen all clamps. Remove both U shaped holders on the sump inlet. Remove screws holding the drain motor. Pull out the pump motor and sump inlet. Connector pump can be unscrewed from the bottom.

Replace parts and reassemble. It isn't that bad once you start disassembly, especially for anyone somewhat handy. Read more...
Your Price
$25.50
  In Stock
Inlet Sump
★★★★★
★★★★★
2 Reviews
PartSelect Number PS1765981
Manufacturer Part Number WD18X10039
This works in conjunction with the pump and filtration system. It is used to receive drainage for disposal.
Fixes these symptoms
Installation Instructions
Scott from GREENSBORO, NC
Water Not Draining.
There are videos on YouTube that demonstrate the repair process better than I can type. I will say I'm not certain why the dishwasher wasn't draining other than when I removed the chamber collection and repositioned the ball filter it would work as it should until the next time. Replacing the sump, chamber collection, and ball filter was a shot in the dark. The tub insulation was an improvement on noise. The first cycle seemed to be draining water better. Overall the removal and installation of the parts was not difficult. Read more...
Your Price
$73.58
  In Stock
DRAIN PUMP W/SCREWS
PartSelect Number PS3486939
Manufacturer Part Number WD26X10049
Fixes these symptoms

Related Parts

Back to Top