General Electric Dishwasher Valves

Your Price

$42.41

Water Inlet Valve

★★★★★

(51)

PartSelect Number PS3654179

Manufacturer Part Number WD15X10014

This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoid on the valve open and close according to the desired amount of water needed.

Fixes these symptoms

Leaking
Not cleaning dishes properly
Not draining
See more...

Installation Instructions

Greg from Burlington, VT

Water leak, small puddle to front left of dishwasher

You'll need to remove the front toe kick and (if installed, the GE Profile baffling for additional silencing action).

You will need to disconnect the right wire connection to access the right screw (and may need to use a flat head screwdriver). You can then remove the 2 screws that hold the Valve Water Inlet on.

You will then need to loosen and the hose clamp that attaches the water line to the Valve Water Inlet. You may need to force it undone since the rubber connection is pretty secure around the water tube inlet.

Disconnect the plastic wire housing from the Valve Water Inlet and you should now have the Valve Water Inlet disconnected.

Reverse the order and reconnect everything and you should be good to go!

Double-check for any leaks prior to pushing everything back in :) Read more...

Your Price

$32.51

Drain Valve Shaft Seal

★★★★★

(11)

PartSelect Number PS263930

Manufacturer Part Number WD8X181

The drain valve shaft seal is a part for your dishwasher drain pump valve. This seal creates a watertight closure around the flapper valve shaft. This part can be accessed through the access panel at the front for a built-in. For a portable dishwasher, consider disconnecting and unplugging the taps and lay on a blanket to access the bottom of the machine. This will need to be replaced if you notice leaking coming from the pump. This part measures approximately 3/8 inches in diameter and is black in color. This is a genuine OEM part that comes right from the manufacturer.

Fixes these symptoms

Leaking
See more...

Installation Instructions

Joseph from Livermore, CA

Water leak from gate (diverter) valve shaft

This was a fairly simple repair. After disconnecting power to the dishwasher and removing the panel below the door, first had to remove a retainer C clip from the gate valve shaft. Then disconnected the linkage from the gate valve solenoid, removed two return springs and slid the gate valve contol arm off the shaft. Then removed the solenoid bracket that was fastened to the housing by 2 screws. This allowed access to the push on nut on the valve shaft. Removed the old push on nut which exposed the leaking seal. Removed the bad seal, then moistened and carefully slid on and seated the new drain valve shaft seal. Affixed new push on nut. Reinstalled the above mentioned parts that were removed. Problem solved - no more leak. Total cost $18.81 for factory GE parts plus $6.95 shipping. Thank you PartSelect. Read more...

Your Price

$92.21

Water Inlet Valve

★★★★★

(14)

PartSelect Number PS259368

Manufacturer Part Number WD15X10003

This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed. This valve has a 3/8" inlet and comes with the mounting bracket.

Fixes these symptoms

Leaking
Not cleaning dishes properly
Not draining
See more...

Installation Instructions

mike from huntley, IL

Dish washer is not running through cycles

First and formost before you buy read everything in trouble shooting your dishwasher. Then you do not buy parts you do not need. First you turn off power, then water. Remove two screws, a rubber hose and a hard line by unscrewing if you are lucky some contractors might sweat this on. No biggie just two extra steps that's all. do in reverse to assemble... Read more...

Your Price

$23.51

Piston and Nut Assembly

★★★★★

(19)

PartSelect Number PS260690

Manufacturer Part Number WD24X10018

This is used for the check valve.

Fixes these symptoms

Leaking
Not cleaning dishes properly
Not draining
See more...

Installation Instructions

Dan from Minnetonka, MN

Dishwasher wouldn't fully drain

I removed the four screws holding the screen and molded plastic cage inside the rear of the dishwasher to expose the check valve assembly. I then unscrewed the piston and nut assembly with my hand and replaced it with the new one. I found that the rubber cone shaped valve on the old piston and nut assembly was entirely disintegrated. This easy repair solved the problem. Read more...

Your Price

$55.54

Water Inlet Valve

★★★★★

(8)

PartSelect Number PS259411

Manufacturer Part Number WD15X93

This water inlet valve is specially designed for those dishwashers that fit under the counter from 1974 To Present. The valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.

Fixes these symptoms

Leaking
Not cleaning dishes properly
Not draining
See more...

Installation Instructions

Don from Mount Vernon, IL

Insufficient fill water, dishes not getting clean (valve diaphram had ruptured)

1. Remove lower cover skirt.
2. Shut of water at undersink valve.
3. Unplug power cord or turn off circuit breaker.
4. Disconnect water supply line from fill valve.
5. Unplug the electrical connector from the valve.
6. Remove the 2 valve mounting bracket screws.
7. With loose valve in hand, rotate to gain access to allow release of outlet hose clamp for hose removal.
8. Remove brass fitting from old valve and install on new valve. Use teflon tape on the pipe threads only.

Install new valve by reversing the procedure. Read more...