Amana Refrigerator Ice Makers

Amana Appliance Parts
Shop By Part Type

Popular Amana Refrigerator Ice Makers

Your Price
$130.33
  On Order
Replacement Ice Maker
★★★★★
★★★★★
(111)
PartSelect Number PS2121513
Manufacturer Part Number D7824706Q
This ice maker (Ice Maker Assembly, Refrigerator Ice Maker) produces ice cubes that are ejected into the storage bucket. It is located in the freezer section of your appliance, mounted on the freezer wall. The ice maker can break from normal wear and accidental damage. If this happens, your refrigerator may no longer make ice cubes, or may not make enough cubes, and the part should be replaced. This model measures approximately 11 inches long and 5 inches wide. It’s constructed of plastic and metal, and comes in black/white/silver. This assembly includes the ice mold and the control device.
Fixes these symptoms
  • Ice maker dispenses too little ice
  • Ice maker dispenses too much ice
  • Ice maker not making ice
  • See more...
Installation Instructions
Bernie from Diamond Bar, CA
Icemaker producing few or no cubes and often leaving "kling-ons" on ice tray
Interior surface of ice tray felt rough & flaky (coating deteriorated) so cubes would not release.
Unplug appliance.
Remove timer cover by hand pressure @ edge.
Remove single attachment screw & bracket at lower front of icemaker.
Disconnect wiring harness from socket @ rear of compartment.
Tricky part was determining what type of connection held the other two attachment points along the long edge of the icemaker. I did not have repair manual or useful drawing but looked @ PartsDirect pic of side brackets & used a small mirror to confirm that mine were also some sort of "snap in" attachment.
Remove icemaker unit by pushing upward and outward on the unit. I takes a good bit of pressure and will pop loose, but be careful not to break attachment bracket from freezer wall.
Scavenge shut off bar and wiring harness from old icemaker once you have it out & attach to new one before installing it back in freezer.
Again, you might find a mirror useful to align those pesky snap-in brackets with the new unit.
Since you probably kept your freezer running while waiting for the part, the plastic snap-ins will be cold and brittle. I warmed them up first by applying a dampened cloth heated in the microwave to make them a little more pliable.
A good push of the new unit towards the snap-ins along with some upward force will get it stable.
Reattach the metal screw in bracket & connect the wiring harness to rear plug... and don't forget to plug the whole thing back in.
It will take awhile for the first batch of cubes dump as the timer may need to cycle completely around to get to the fill cycle... be patient.
Dump the first couple of batches of cubes just to make sure you're free of any residue.
Read more...
Your Price
$128.78
  On Order
Replacement Ice Maker
★★★★★
★★★★★
(105)
PartSelect Number PS358591
Manufacturer Part Number 4317943
This ice maker (Complete Icemaker Assembly, Whirlpool Icemaker Kit, Ice Maker Assembly, Refrigerator Ice Maker, Icemaker) receives water from the water inlet valve, freezes it, and dispenses it into the ice bucket until the bucket is full. Ice makers will need to be replaced every 3-10 years depending on the frequency of usage, and water quality. You can perform a voltage test with a multimeter or perform an inlet valve test. If you’re unable to make ice, or notice leaks then it may be a sign your ice maker is damaged and could be in need of a replacement. This model measures approximately 11x5 inches, is constructed of plastic and metal, and comes in black/silver. This ice maker is a complete assembly; the whole assembly attaches to the wall of your freezer.
Fixes these symptoms
  • Ice maker dispenses too little ice
  • Ice maker dispenses too much ice
  • Ice maker not making ice
  • See more...
Installation Instructions
GLENN from ORLAND PARK, IL
was not making ice
take out ice bucket, just loosen the top 2 screws, remove the bottom screw, slide ice maker up & out, srewdriver to release wiring harness clip, reverse to put back in. was very simple. did not install water inlet kit yet. water under fridge stopped after i changed the ice maker. Read more...
Your Price
$85.10
  On Order
Refrigerator Ice Maker Assembly
★★★★★
★★★★★
(48)
PartSelect Number PS11765620
Manufacturer Part Number W10884390
Fixes these symptoms
  • Ice maker not making ice
  • Ice maker won’t dispense ice
  • See more...
Installation Instructions
Raymond from NORTH VENICE, FL
Ice maker did not work in the bottom freezer
Shut down refrigerator at the breaker. Placed freezer items in a cooler. Removed top shelf. You must release roller covers on each side to remove the shelf ( Two front screws must be removed) Took off freezer door. (4 screws holding the door to the bracket) Disconnected ice maker electronic plug. Totally removed bottom screw holding ice maker. Loosen two top screws and remove ice maker. Reverse process to install. Read more...
Your Price
$104.42
  In Stock
Refrigerator Freezer Ice Maker
★★★★★
★★★★★
(28)
PartSelect Number PS11769140
Manufacturer Part Number W10882923
Fixes these symptoms
  • Ice maker not making ice
  • Ice maker won’t dispense ice
  • See more...
Installation Instructions
Greg from ALISO VIEJO, CA
Stopped making ice, confirmed ice in trough, not ejecting ice or cycling
Please note I had to remove the complete old wire harness from and install the new proper one as my part number was replaced with a new part number. The new ice maker repair kit comes with 2 new harnesses each slightly different one for a 22 cubic foot model the other for the 25cf model. It looks intimidating initially, just take pictures FIRST BEFORE removing old harness to see all the connections. I was surprised this was necessary but it is, as the 'H" pin on the front of the new ice maker motor was different from my old one. Would have only taken me 15 minutes or so to replace the old ice maker but with having to remove the old harness and re-route the new harness it will take you a bit of time and patience but you can do it. Another note you will have to remove the Electromagnet to get to the green grounding screw on the ice maker itself. There are good videos on Part Select and youtube showing how to remove the ice maker itself, but did not find one on the wire harness, like I said just take lots of good pictures showing all the connection points on the old harness and take your time. It was not too hard. And now I have ice again! Read more...
Your Price
$74.62
  In Stock
Ice Bucket
★★★★★
★★★★★
(26)
PartSelect Number PS11757044
Manufacturer Part Number WPW10670845
Bucket only. All other parts sold separately. This part holds the ice once it's released from the icemaker.
Fixes these symptoms
  • Ice maker not making ice
  • Ice maker won’t dispense ice
  • Leaking
  • See more...
Installation Instructions
Robert from Valencia, CA
Ice maker's ice tray coating coming off, ice bin had foul odor.
I noticed the coating inside the ice maker, the lining on the surface that the water contacts when making ice, was chipping off. I replaced the ice maker with a new unit and now there's no more bits of stuff in my ice. The other problem I had was the ice bin, it had picked up a weird smell over the years and I wanted to replace it. The new bin seems flimsier, but works fine. It didn't have the top attachment hole for the ice auger mechanism drilled out for some reason, it had a little "bump" in the plastic where it should be, but was never drilled out. Easy enough, I drilled the hole out and attached that top screw without any issue. Read more...
Your Price
$106.58
  On Order
Ice Maker
★★★★★
★★★★★
(23)
PartSelect Number PS11749920
Manufacturer Part Number WPW10190965
This is an icemaker for your refrigerator/freezer. Take note that this part does not include the front cover, the wire harness, or the shut-off arm. These must be ordered separately or recycled from your old unit. This unit as a whole will allow your appliance to produce ice. This model makes eight radius ice cubes.If your ice maker is no longer making ice, dispensing ice, or if it is leaking, it will need to be replaced.
Fixes these symptoms
  • Ice maker not making ice
  • Ice maker won’t dispense ice
  • Leaking
  • See more...
Installation Instructions
Jamie from Mitchell, SD
Ice maker quit working
First I removed the three screws with a nut driver and then disconnected the wire plug from the old ice maker. I plugged in the new unit and re-installed the screws and instantly the unit started to work. I did have to adjust the water level on the unit ...just turn the small plastic knob (use a slotted screw driver) on the side of the unit counterclockwise to increase the water level (do not turn more than one full turn or you could damage the unit) . It works perfect and saved me lots of money!! Read more...
Your Price
$93.39
  In Stock
Add-on Ice Maker Kit
★★★★★
★★★★★
(17)
PartSelect Number PS11757272
Manufacturer Part Number WPW10715708
This genuine OEM ice maker kit is designed to fit refrigerators that did not originally come with an ice maker. This kit contains everything needed to install the new ice maker on your refrigerator including: the ice maker, ice bin, inlet valve, fill tube, and hardware. If your new ice maker does not function properly after being installed, check the freezer temperature. The freezer must to be around zero degrees Fahrenheit. Remember to disconnect the power and water supply to your refrigerator before beginning this installation. Make sure to check that your model is compatible with this part before ordering. Note: The manufacturer has updated this part. It may differ in appearance but will function the same as the original.
Fixes these symptoms
  • Ice maker not making ice
  • Ice maker won’t dispense ice
  • Leaking
  • See more...
Installation Instructions
Donald A. from ORLANDO, FL
Wanted to install ice maker in my freezer
I was clening my uprght freezer and noticed that it was preped for an icemaker. I first went to the Whilpool website and could not find my part as my freezer was a 2008 model.

I saw PartSelect on the search page and went to thier site.
I put in my modle number of the Whilpool Ice maker kit that was on the back of my freezer. PartSelect had the part in stock and approx $18.00 less than the other kits listed on the Whilpool site (that did not match my kit number). I orderd the kit on Sunday and it arrived on Wednesday. It took less than and hour to install. Every part I needed was included. The following day I installed the water line and now I have an extra icemaker.
Read more...
Your Price
$107.05
  In Stock
Icemaker Control Assembly
★★★★★
★★★★★
(16)
PartSelect Number PS2341896
Manufacturer Part Number W10190935
The “Icemaker Control Assembly” (Module & Motor Assembly, Ice Maker Control Module, Icemaker Module, Refrigerator Ice Maker Module) is what controls the actions of your ice maker. The control turns the timing cams and the ejector blades. It controls most of the basic parts and functions such as the heater, water inlet valve, the cube size, and cube ejection. If your ice maker control is broken it can no longer properly control the ice maker functions. It may not produce any ice, make small ice cubes, or have intermittent operation. This can occur due to normal wear and tear. The icemaker control assembly is attached to the ice maker mold, and is under the white cover. Test the icemaker control assembly by using a multimeter. If this reveals the assembly to be defective, you will need to replace this part. It is approximately 4.25 inches square, beige, and is constructed of plastic and metal. This replacement part features one icemaker control assembly, including the control module and the motor.
Fixes these symptoms
  • Ice maker not making ice
  • Ice maker won’t dispense ice
  • Leaking
  • See more...
Installation Instructions
Daniel from Suwanee, GA
No ice
removed flap door in front of icemaker...removed 3 screws with bolt heads...removed one additional screw with bolt head and ice unit slid out. I removed motor unit (pops out no screws). Replaced and had ice within 3 hours. Read more...
Your Price
$39.82
  On Order
Ice Bin Auger Drum
★★★★★
★★★★★
(18)
PartSelect Number PS372186
Manufacturer Part Number 4388736
This white ice bin auger drum comes with a washer.
Fixes these symptoms
  • Ice maker dispenses too little ice
  • Ice maker not making ice
  • Ice maker won’t dispense ice
  • See more...
Installation Instructions
john from seaford, VA
Plastic bits dispensed from Ice Dispenser in Door
Removed Ice bin from Fridge

Removed all bolts on bin with nut driver...about six

Removed housing...be careful with spring on crusher/cube control rod

Removed C clamp on end of auger with small slotted screw driver and needle nose pliers.

Removed plastic nut on end of auger shaft

Removed Ice crusher jaws and laid them out in the correct order

Removed Ice propeller and installed new part

Put back together in opposite order

Easy
Read more...
Your Price
$174.13
  On Order
REFRIGERATOR Ice Maker Replacement
★★★★★
★★★★★
(11)
PartSelect Number PS11752389
Manufacturer Part Number WPW10300022
The replacement ice maker does not include a new ice level arm, or wire harness, these components will need to be reused from original ice maker.
Fixes these symptoms
Installation Instructions
John from WELLTON, AZ
The ice maker had a internal brownish leak substance. This in turn dripped on the ice in the tray, which froze the ice cubes in a ball which would not let the ice to be ejected from the dispenser, and in turn cracked the tray which holds the ice cubes, so I had to replace the tray and ice maker.
On a side by side refer, you need both doors open to unscrew the three 1/4 inch screws,
1. Remove the ice tray
2.the ice arm needs to be in the up position, so no water will flow while dissembling.
3. Remove the two top screws,
4. While holding the ice maker with o e hand, remove the bottom screw.
Balance the ice maker and unplug the ice make electric plug in the rear of the ice maker.
5. Take the I e maker out.
6. The ice maker does not come with the ice arm, so you need to remove the arm from the old or broken ice maker and install it in the new ice maker.
7. Resemble in reverse order.

I did not unplug the refer from the wall socket, you may want to do this. It recommended but I did not.
There you go.
Read more...

Related Parts