Whirlpool/Whirlpool_Thumb/ROSE3DQ0.gif
See part 100 in the diagram
( Grid squares measure 1x1 inch )

Get in touch, we're here to help!

Open until 12am EST

customerservice@partselect.com

Refrigerator Ice Maker Assembly

★★★★★
★★★★★
58 Reviews
$ 100.24   In Stock

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

PartSelect Number PS11765620
Manufacturer Part Number W10884390
Manufactured by Whirlpool
Troubleshooting
This part fixes the following symptoms:
Ice maker not making ice | Ice maker won’t dispense ice | Ice maker dispenses too much ice
This part works with the following products:
Refrigerator.
This part works with the following products:
Whirlpool, Maytag, Kenmore, KitchenAid.
Part# W10884390 replaces these:
AP6030643, W10377152, W10469286, W10793298, WPW10377152, WPW10469286
Questions and Answers

Ask our experts a question about this part and we'll get back to you as soon as possible!

45 questions answered by our experts.
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Henry
October 24, 2017
Is this the whole ice maker
For model number W10469286
Hi Henry, Thank you for your question. Yes, this is your entire ice maker. Good luck with your repair.

40 people found this helpful.

Was this helpful?
Thank you for voting!
Sandra
January 13, 2018
Is new wiring harness included?
Hello Sandra, Thank you for your inquiry. The wiring harness is not included, you will have to use the harness from the old ice maker. Hope this helps!

15 people found this helpful.

Was this helpful?
Thank you for voting!
JEFF
January 23, 2019
Does ice maker comes with cycling thermostat and can i tell if ice maker is bad or thermostat
For model number MFF2558DEM00
Hello Jeff, thank you for your question. Yes, the icemaker comes with the thermostat. This thermostat controls and regulates the ice maker ejection cycle by monitoring the temperature inside the freezer to determine when to release the ice into the bin and start the ice making cycle again. If your ice maker is making unusual noises, or if the ice maker is not making or dispensing ice, there could be an issue with the thermostat. You can test this thermostat with a multimeter to see if it has continuity. If the thermostat does not have continuity you would want to replace the thermostat itself. I hope this helps!

8 people found this helpful.

Was this helpful?
Thank you for voting!
George
February 6, 2019
The ice maker does not dispense ice. Will this part resolve this problem?Thank you.
For model number GSF26C5EXY02
Hello George, Thank you for the question. if the ice maker is still making ice then the ice Maker is fine. If the ice is not dispensing, you can try to remove the ice container and let it sit out to thaw any ice build up within the container. If this does not fix the issue you can take the bin apart and check for any damaged parts within the container. You should be able to hear the motor in the container when it is trying to dispense. If the motor is not turning on to dispense, you may have a defective Motor, Part Number: PS11740462. Hope this helps!

6 people found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
Ken
January 16, 2020
No ice. Water valve functional upon testing with 120v.....water flows......i re started fridge and am waiting for fill valve to energize.....anything i can look for.....would like to test the functions from the front but not sure if i need to......the bar moved when I restarted the equipment.
For model number GX5FHDXVY09 and Serial: K22905993
Hi Ken, thank you for your question. In most cases, if both of the solenoids on your water inlet valve are testing within 500 - 1500 ohms of resistance, then the problem would be with the ice maker not calling up water to start making the ice. Which means that you may have to replace your ice maker itself if the issue is not in your water valve. Good luck with your repair.

5 people found this helpful.

Was this helpful?
Thank you for voting!
John
January 23, 2019
How do you adjust the ice cube size?
Hello John, Thank you for the question. There is a small plastic screw at the front of the icemaker that would be an adjustment screw and you would simply turn it a 1/4 turn counter clockwise but no more than that. Hope this helps!

5 people found this helpful.

Was this helpful?
Thank you for voting!
James
November 13, 2019
What is the part# for the ice maker for the refrigerator model number above
For model number MFF2558DEH00
Hello James, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is PartSelect Number PS11765620. Hope this helps!

3 people found this helpful.

Was this helpful?
Thank you for voting!
Shari
February 6, 2020
I asked this question but it was answered wrong. I stated my refrigerator wont stop making ice, so wondering what to do. The answer i received was regarding an ice maker not working which isn't my issue. The problem is, it keeps making ice, the metal lever doesnt stay up which is supposed to stop it from making ice. Thanks.
For model number kitchenaid fridge krff305ebs
Hi Shari. If the arm won't stay up you can try replacing the shut off arm PS11750229. Thank you for your question and good luck with your repair.

2 people found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
James
February 15, 2020
1. My fridge is 5 years old and is located in a vacation home. I shut off the r/o water supply to the appliance but forgot to turn the ice maker off by putting the handle in the off position. When i turned the water supply back on, the ice maker wasn't producing ice. 2. Does this model have an internal filter? I can't see one in any obvious locations.
For model number WRB322DMBW00
Hi James. It has what is called a drier filter linked below. The most common for this is replacing the icemaker assembly. Thank you for your question and good luck with your repair.

2 people found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
Marshall
January 30, 2020
Does this ice maker assembly work for the model numbers I listed above?Thanks
For model number kfcs22evms6
Hello Marshall, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is PartSelect Number: PS11765620. We hope this helps.

1 person found this helpful.

Was this helpful?
Thank you for voting!
Customer Repair Stories
 Average Repair Rating: 3.4 / 5.0, 21 reviews. What's this?
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
Ice maker did not work in the bottom freezer
Shut down refrigerator at the breaker. Placed freezer items in a cooler. Removed top shelf. You must release roller covers on each side to remove the shelf ( Two front screws must be removed) Took off freezer door. (4 screws holding the door to the bracket) Disconnected ice maker electronic plug. Totally removed bottom screw holding ice maker. Loosen two top screws and remove ice maker. Reverse process to install.
  • Raymond from NORTH VENICE, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Socket set
26 of 33 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice maker was leaking fresh water into the tray freezing large clumps of cubes together.
First and foremost shut off the water supply to the Ice maker. Some recommend unplugging the refrigerator or disabling the circuit breaker to the refrigerator. Then after emptying the freezer remove the freezer door by loosening the four hex head screws and lift the door straight up and set it off to the side.You can then remove the lower basket. Now locate the clamps located at the rear sides of the inner basket and use a small flat blade screwdriver to gently push the tabs toward the outside of the side clamps while pulling up at the same time and releasing the clamp. Now repeat this procedure on the opposite side of the inner basket. The inner basket can then be pulled out being careful to not damage the roller tracts or gear rollers. Three hexhead screws secure the ice maker to the wall. The screw under the ice maker must be removed while the two on top just loosened. The electrical plug is removed by depressing the tabs on the top and bottom of the plug and then pulling outward. Carefully lift the ice maker upward and out from the two upper hex head screws. You can then install the replacement icemaker by reversing the procedure.
  • william from GROVE, OK
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
10 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
icemaker stopped working
Hardest part is access to the icemaker itself. Once I removed the freezer door (bottom drawer freezer), and got the sliding basket out, it was a 10 minute job. Make sure you start the upper screws first, the icemaker will hang there while you adjust, connect the harness, and tighten. Make sure you are ready before you close the door, it will start making ice as soon as the door is closed.
  • Charles from CASTLE ROCK, CO
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
ice maker quit working 2 years old
the shelf in the bottom load freezer compartment can not be removed and therefore impossible to get bottom screw in the holds the ice maker replacement in place the materials used to hold the veggie drawers is not strong enough there is broke and was necessary to put a stick in to support the weight The sticker say American made ---but this product is nothing to be proud of
  • Don from OCEAN ISL BCH, NC
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers
4 of 39 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Existing icemaker would freeze up, stop making ice.
I did not unplug the refrigerator. Your choice on this. Take a close look at the existing icemaker, how the wires are routed and what the water spout looks like as it relates to the icemaker. Small flat-blade screwdriver will help in unlocking tabs on the icemaker plug. Go ahead and unplug it. Of the three screws that secure the icemaker, two are impossible to see without holding a mirror in your third hand. Completely remove the bottom screw (by feel). Don't drop it, like I did. Have no idea where it went. Loosen the top two screws but do not remove. Icemaker will lift off of the top two screws when you push it up. With old icemaker out of the way, plug in the new icemaker. Be careful to properly align the water spout into the new icemaker as you hook it on the two top screws. When everything looks good, tighten the two top screws. Replace the bottom screw, if you didn't lose it. My icemaker is doing fine without a bottom screw. It should make some ice within an hour, or so. Mine did.
  • Steve from WAKE FOREST, NC
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice maker replacement
Loosen the top 2 screws, remove the bottom screw, unplug the wire harness, lift up the ice maker and remove. To install the new one simply reverse the removal procedure.
Note: You may want to wipe the inside of the new one to remove the protective grease or discard the first 2 cycles of ice.
  • John from CENTEREACH, NY
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Socket set
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Icemaker quit making ice
removed the freezer door, removed the two shelves and removed three screws from the icemaker, unplugged the wiring harnest. Installed the new icemaker in reverse procedure.
  • Phillip from JASPER, AL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice maker quit working
Unplugged wire plug, removed mounting screws and removed ice maker. Installed new unit by reversing steps--
  • Lloyd from Algona, IA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice was not ejecting - motor was dead
Followed some online videos. The replacement part actually matched exactly what the videos I found showed. It was my refrigerator that was slightly different where the unit would mount/screw into. The old unit had a bracket which easily attached to the replacement part. It is less than a 1 hour repair for sure. But it took me a few minutes to figure out the bracket adapter. Plus I forgot to seat the ice maker shut off bar and had to disassemble some things again to get in there to seat it properly. Part was shipped quickly and securely !
  • David from PITTSBORO, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
difficult to reach mounting screws without removing top freezer rack
Loosen the 2 mounting screws on the top about 2 turns; take the one mounting screw on the bottom all of the way out. The top part of the ice maker drops down on the loose top screws. That holds the ice maker while installing the bottom screw. No need to shut off water to the ice maker, just shut off electricity to refrigerator.
  • Beverly from RIO RANCHO, NM
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer Reviews
Average Rating:
★★★★★
★★★★★
58 Reviews
4.7
Filter By Rating:
  • 5 Stars
    45
  • 4 Stars
    9
  • 3 Stars
    2
  • 2 Stars
    1
  • 1 Star
    1
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11765620
Manufacturer Part Number: W10884390
Brand
Model Number
Description
Kenmore
10672002011
Refrigerator - REFRIGERATOR
Kenmore
10672002013
Refrigerator - REFRIGERATOR
Kenmore
10672002015
Refrigerator - REFRIGERATOR
Kenmore
10672003012
Refrigerator - REFRIGERATOR
Kenmore
10672003013
Refrigerator - REFRIGERATOR
Kenmore
10672003014
Refrigerator - REFRIGERATOR
Kenmore
10672003016
Refrigerator - REFRIGERATOR
Kenmore
10672003017
Refrigerator - REFRIGERATOR
Kenmore
10672003018
Refrigerator - REFRIGERATOR
Kenmore
10672009011
Refrigerator - REFRIGERATOR
Kenmore
10672009013
Refrigerator - REFRIGERATOR
Kenmore
10672009015
Refrigerator - REFRIGERATOR
Kenmore
10672013017
Refrigerator - REFRIGERATOR
Kenmore
596467934251
Refrigerator - REFRIGERATOR
Kenmore
596467934351
Refrigerator - REFRIGERATOR
Kenmore
596467934451
Refrigerator - REFRIGERATOR
Kenmore
596467934951
Refrigerator - REFRIGERATOR
Kenmore
59672002011
Refrigerator
Kenmore
59672002013
Refrigerator - REFRIGERATOR
Kenmore
59672002015
Refrigerator - REFRIGERATOR
Kenmore
59672003012
Refrigerator - REFRIGERATOR
Kenmore
59672003013
Refrigerator - REFRIGERATOR
Kenmore
59672003014
Refrigerator - REFRIGERATOR
Kenmore
59672003016
Refrigerator - REFRIGERATOR
Kenmore
59672003017
Refrigerator - REFRIGERATOR
Kenmore
59672003018
Refrigerator - REFRIGERATOR
Kenmore
59672009011
Refrigerator
Kenmore
59672009013
Refrigerator - REFRIGERATOR
Kenmore
59672009015
Refrigerator - REFRIGERATOR
Kenmore
59672012012
Refrigerator

Get in touch, we're here to help!

Open until 1am EST

Contact Customer Service