Amana Refrigerator Thermostats

Amana Appliance Parts
Shop By Part Type

Popular Amana Refrigerator Thermostats

Your Price
$29.82
  In Stock
Bi-Metal Defrost Thermostat
★★★★★
★★★★★
(20)
PartSelect Number PS11750673
Manufacturer Part Number WPW10225581
If you have ice building up in your freezer, or if your freezer is getting too warm during the defrost cycle you may need to replace the bi-metal defrost thermostat. The function of the defrost bi-metal thermostat is to clip onto the evaporator and protect your evaporator from overheating during the defrost cycle. If your refrigerator does not defrost properly you can test both the thermostat and the heater to figure out which part is at fault. For this repair, you will need a Phillips screwdriver, a 1/4 inch nut driver, a flat blade screwdriver, a pair of wire strippers, a roll of electrical tape, and a few butt splice connectors.
Fixes these symptoms
  • Freezer not defrosting
  • Freezer section too warm
  • Freezer too cold
  • See more...
Installation Instructions
Laune from Front Worth, TX
Both freezer and refrigerator stopped cooling
Compressor Start Divice kit, I took off back lower panel with the 1/4 inch nut driver, on the compressor their was a wire hook that held the starter in place used my plyers to unhook, pulled the unit off plug the new unit in reappled the clip it was so easy I had to exame it severl to time to make sure that was all their was to it. put the cover back on and turn the refrigerator on and it has work great, I did not install the Bi-Metal Defrost Thermostat it was not needed. Read more...
Your Price
$92.63
  On Order
Thermostat Assembly
★★★★★
★★★★★
(30)
PartSelect Number PS11739232
Manufacturer Part Number WP2198202
This thermostat assembly is used in refrigerator units and freezers as a sensor. The thermostat senses the temperature increase in the evaporator during the cycle of defrosting and turns off when ice is melted. If you have any of the following symptoms, replacing your appliance could solve the problem: fridge does not start, is too warm, too cold, runs too long, or will not start. The tools needed for this repair project is a putty knife, Phillips and flat blade screw driver, 1/4 inch nut driver, and needle nose pliers. Remember to unplug refrigerator from power source as a safety precaution. Refer to the manual provided by the manufacturer for further installation instructions.
Fixes these symptoms
  • Freezer section too warm
  • Freezer too cold
  • Fridge and Freezer are too warm
  • See more...
Installation Instructions
Steve earney from Brooks, GA
inconsistent compressor and condensor fan operation
Compressor start relay would cycle several times before compressor would come on. Replaced start relay and defrost timer assy. Operated more consistently however not completely reliable. Ice would begin to melt. Noticed that if you would cycle the temperature control the compressor would start again and operate for several hours then not cycle again. Jumpered temp control and operation was continuous and reliable. Replaced cold control thermostat. Operation now normal. Suspect high resistance in switch caused start relay and timer contacts to arc. Small amount of carbon noticed under temp control... Read more...
Your Price
$26.78
  In Stock
Bimetal Defrost Thermostat
★★★★★
★★★★★
(12)
PartSelect Number PS11742474
Manufacturer Part Number WP4387503
This is a bimetal defrost thermostat for your refrigerator. It stops the fridge from overheating during the defrost cycle by protecting the evaporator. This clip-on thermostat will sense the temperature increase in the evaporator during the defrost process, and will cycle the defrost heater off after the ice or frost is melted. The most common reasons for needing to replace this part are if your unit is leaking, has inconsistent temperatures (too hot or too cold), you are seeing buildup of ice, or your appliance is running too long.
Fixes these symptoms
  • Freezer not defrosting
  • Freezer section too warm
  • Freezer too cold
  • See more...
Installation Instructions
Lawrence from Grahamsville, NY
The frost free feature of the freezer was freezing over with ice and cooling coils were being insulated with thickening frost which caused the cooling air to rise in temperature from -5 degrees to 20 degrees.
I troubleshot the problem by reading the electrical schematic and concluding the heating elements (defrost cables) were either defective or the bi-metal temp sensor was open. When closed the temp sensor completes the circuit for the current to flow through the heaters to defrost the cooling coils every 8 hours and then when the bimetal opens at 55 degrees the circuit is open and the coils are cooled because the refridgeration motor is in run mode. A timer between the motor and heater elements also was defective. The timer controls the cooling period and the defrost period. I ohmed out each part according to the spec sheet of normal resistance of parts and thus the bimetal and timer were defective. I gather a surge of some duration and amplitude affected these parts because a storm 24 hours prior to refridgerator problem had passsed through the area and the AC electrical power had oscillated several times during that event. I used hand tools to do the repair. If you are not mechanically inclined a step by step proceedure would be moot. It is a matter of disassembly and assembly paying close attention to fragile parts. Read more...
Your Price
$35.14
  In Stock
Thermistor
★★★★★
★★★★★
(3)
PartSelect Number PS2003772
Manufacturer Part Number 12002355
Long harness thermistor kit.
Fixes these symptoms
  • Freezer not defrosting
  • Freezer section too warm
  • Freezer too cold
  • See more...
Installation Instructions
Gordon from Ben Wheeler, TX
Freezer cold, refrigerator warm
Overload relay accessible from back, by compressor unit. Very easy to change out. Diagram from your site placed defrost thermostat in same area.It wasn't. Found another diagram, showed it in refrigerator light area, took that apart, not there. Yet another diagram showed it in the duct work area at back of refrigerator cabinet. Not there. Finally removed back of freezer compartment, found thermistor and thermostat with the fins. Clipped wires, wired in parts, quick fix. Longest amount of time was spent finding the old parts to replace them. Actual replacement took less than 15 minutes. Refrigerator holding at 35 degrees set on 2 now, better than ever. Total cost, less than $120, doing iy ourselves....priceless. Read more...
Your Price
$87.23
  On Order
Thermostat
★★★★★
★★★★★
(9)
PartSelect Number PS11740364
Manufacturer Part Number WP2315562
Helps to maintain the proper temperature in the freezer and fresh food compartments.
Fixes these symptoms
  • Freezer section too warm
  • Fridge and Freezer are too warm
  • Fridge too cold
  • See more...
Installation Instructions
Garry from Ochelata, OK
food freezing in the refrigerator
Remove the front panel strip where the temperature adjustment lights show, use a thin screw driver to pot the strip out along the top. Use a nut driver to remove the control panel which contains the light, two bolts on the under side, two bolts on the front after the panel strip was removed. The control panel will hang down enough with the wires attached to allow access to the thermostat. Use a Phillips screw driver to remove the side cover where the temperature probe runs along the left hand side to the unit, one screw. You will find the temperature probe inside plastic tubing running to the back of the unit where it is wrapped around a Styrofoam holder with three plastic retainer clips on the top and bottom. Unplug the thermostat from its electrical connection. You may want to unplug the unit’s wall plus as this is 110 volt connection. Remove the two screws holding the thermostat to the plastic control panel; remove the fiber optic connection to the light strip that runs across the top of the thermostat. Remove the temperature probe from the 6 clips and pull the entire unit out. Remove the plastic tube from the old temperature probe and slide it over the probe from the new thermostat. The probe is approximately 26 inches long and you must take care not to crimp it as you slide it in the plastic tubing(warm the plastic tube with a hair dryer to reduce stiffness at the bend). Plug the wires into the new thermostat and reassemble. Read more...
Your Price
$69.27
  In Stock
Damper Control Assembly
★★★★★
★★★★★
(4)
PartSelect Number PS11750106
Manufacturer Part Number WPW10196393
This part allows the cold air from the freezer section to be aired into the fresh food section and it is controlled by the thermostat.
Fixes these symptoms
Installation Instructions
chip from Reading, MA
the upper half of the refrigerator wasn't being cooled
I called the repairman and he troubleshot the problem and told me that he could order the part or that I could. He quickly explained what to do. I ordered the part it came in with 2 days during that time I looked up on how to remove and replace the part on the website. The website stated it took around 15 minutes. That is all it took. I had to use a screw driver to remove two screws and seperate the connection. I reconnected the wiring per instructions on the website reversed the process and it was done within 15 minutes. I save a lot of money and time away from work. This is a grest site to get what you need to fix your appliances. If I have any problems with my other equipment I will becoming back to this website to get the parts and information

I want to thank you for providing the information and helping folks out that can do the job
Read more...
Your Price
$40.56
  In Stock
Defrost Thermostat
★★★★★
★★★★★
(6)
PartSelect Number PS11743535
Manufacturer Part Number WP67003426
This defrost thermostat is a temperature sensing mechanism used in freezers and refrigerators. The thermostat senses the rise in evaporator temperature during a defrost cycle and turns the defrost heater off once frost is melted from the coils. If the freezer is not defrosting, or the freezer section is too warm, it is best to replace the thermostat to fix the problem. The tools needed for this project are: 1/4 inch nut driver, flat blade screwdriver, needle nose pliers, wire strippers, and pair of wire nuts. Remember to unplug your appliance from the power source for safety and refer to the manual provided by the manufacturer for installation instructions.
Fixes these symptoms
  • Freezer not defrosting
  • Freezer section too warm
  • Freezer too cold
  • See more...
Installation Instructions
Cheryl K from Pinellas Park, FL
The refrigerator was not getting cold and the coils were not defrosting.
Start by removing the freezer door and inner baskets so you have some space. Next, take out the ice maker by removing the 3 screws that attach it to the side and unplug it from the harness. Then the cover for the thermistor and the fan vent should be popped off carefully leaving the back cover only. The back cover is held on by 4 screws, one in each corner. Remove all 4 screws and carefully loosen the back cover by pulling the top forward and laying it level to pull it out. Behind the cover are the coils and other components. If the coils are covered with ice they should be defrosted by using a blow dryer. Once the ice is clear, the thermostat is located towards the top left clamped onto a copper pipe that circles up and around. Carefully pull it off the pipe and cut the wires making sure you leave enough to reattach the new ones with a butt connector. Strip about 1/4 inch of insulation off the wires and crimp both ends into the butt connector making sure they are tight. Heat shrink is highly recommended. Clamp the new thermostat to the copper pipe where the old one used to be and your almost done. Replace the back cover the opposite of the way it was pulled out by putting it in flat with the bottom part in front. Once it is all the way to where it needs to be, push the top upwards while sliding the bottom downwards, then push it in flat against the back. It can be bent slightly if needed. Put the screws back in that hold it on and replace the plastic covers. Then reinstall the ice maker being sure the hose for the water is correctly positioned so that the water goes into the ice maker. Turn it back on and put the baskets and door back on and you're done. Read more...
Your Price
$39.47
  In Stock
Cycling thermostat
★★★★★
★★★★★
(1)
PartSelect Number PS11743313
Manufacturer Part Number WP627985
The ice maker thermostat, also known as the cycling thermostat, controls and regulates the ice maker ejection cycle by monitoring the temperature inside the freezer to determine when to release the ice into the bin and start the ice making cycle again. If your ice maker is making unusual noises, or if the ice maker is not making or dispensing ice, there could be an issue with the thermostat. Before you begin this repair, make sure the power is disconnected from your refrigerator, and that any food that may spoil is safely stored. This is an OEM part and is sourced directly from the manufacturer. This thermostat is sold individually, and comes with two attachment clips.
Fixes these symptoms
  • Ice maker not making ice
  • Ice maker won’t dispense ice
  • See more...
Installation Instructions
Wayne from Leesburg, FL
No ice in ice trey
The easiest thing to do was pull the ice make off. After taking the 3 screws out of the wall of the freezer, take a screwdriver (flathead) and push on the tab for the electrical plug and wiggle the cord out. Then you can take 3 screws out for the main cover and another 2 screws on the next cover. There's the part, pop it out and replace holding pins and start the process of putting back together the opposite way you took it apart. Read more...
Your Price
$41.48
  In Stock
Bimetal Defrost Thermostat
★★★★★
★★★★★
(1)
PartSelect Number PS11738231
Manufacturer Part Number WP10442411
This refrigerator defrost thermostat will cut out at 55 degrees Fahrenheit and kick back in when the temperature drops to 20 degrees Fahrenheit. The thermostat itself is a little over an inch long while its extending wires are almost seven inches long.
Fixes these symptoms
  • Freezer not defrosting
  • Freezer section too warm
  • Freezer too cold
  • See more...
Installation Instructions
James from Canyon Country, CA
Frig was hot freezer was cold. Freezer was fronzen over.
The frig was hot but the freezer was cold. I opened the back of the freezer and found the condenser all frozen over. Upon inspecting the defrost thermostat I found that it was split open, as if water got into it and the froze breaking it open. I used a blow dryer to defrost the condenser. I then spent a long time trying to find the model on-line, even the manufactor said it did not exist. Partselect.com was the only place that said the model did exist. When that part came in I toke the back of the freezer out again. Unplugged the defrost thermostat plugged the new one in clipped it back on the condenser and put the it all back together. Everything is working fine now. Read more...
Your Price
$49.13
  In Stock
Defrost Thermostat Kit
★★★★★
★★★★★
(2)
PartSelect Number PS2003451
Manufacturer Part Number 12001937
This part is snapped onto the top portion of the evaporator. The thermostat sends temperature information to the processor. The defrost heater must be replaced when replacing the thermostat.
Fixes these symptoms
  • Freezer not defrosting
  • Freezer section too warm
  • Freezer too cold
  • See more...
Installation Instructions
james from southampton, PA
Freezer not defrosting
Removed shelf drawer. Then removed plastic coverings from back panel of freezer. Squeezed tabs of ice maker connector to push it behind the back panel. With nut driver, removed the four screws holding the panel and removed the panel. Used a hair dryer to remove frost from upper right area that contains the defrost thermostat. Cut out the thermostat and removed the connector on the right from the defrost heater. Removed brown wire from a few of the clips. Attached orange wire from new thermostat to orange wire leading to connector removed from defrost heater and the brown wires to each other using the pliers and supplied crimpable wire nuts. Wrapped the connections with self fusing tape. Reconnected the wiring to the defrost heater and clipped the new defrost thermostat to where the defective one was removed. Used the hair dryer to melt the ice that was covering the drain, then a turkey baster to unclogg the drain. Put everything back together. Read more...

Related Parts