Amana Refrigerator Dispensers
Find your part
Enter your model number or a part number and click "Search"
Popular Amana Refrigerator Dispensers
Your Price
$64.82
Ice Door Kit
PartSelect Number PS11723180
Manufacturer Part Number W10823377
In this kit you will find the support, the ice door, spring, and delay. The heater ribbon is no longer needed and therefore will not be included with this part. This kit works in the dispenser chute to let ice through when it is being dispensed. If you have the following symptoms such as: door sweating, difficulty opening or closing door, frost buildup, warm freezer section, or problems with ice dispensing, then this is a solution. The tools needed for this repair are a putty knife, needle nose pliers, and 1/4 inch nut driver. Wear work gloves to protect your hands when performing this repair.
Fixes these symptoms
- Door Sweating
- Door won’t open or close
- Freezer not defrosting
- See more...
Installation Instructions
BILL from BATESVILLE, MS
Front Door Ice Wouldn't Work And Air Going Into Freezer
Thanks to the pictorial diagram, I was able to order correct parts. It was just a matter of removal of broken parts and replacing them. Ice maker now working and air is no longer getting into freezer which was freezing up ice maker. Thanks for timely delivery, now I am able to use ice dispenser, which I haven't used for long time. Thanks
Read more...
Your Price
$30.51
Refrigerator Dispenser Overflow Grille
PartSelect Number PS11739623
Manufacturer Part Number WP2206670B
This grille is located on the bottom of the ice/water dispenser to catch the overflow. (Black)
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
Raymond from Coconut Creek, FL
Kitchenaid refrigerator shelf frames were cracking, needed replacement
I had to purchase two shelves and adjustable brackets - though I only needed the slidign glass shelves . Customjer service rep was helpful and pleasant, though the replacements shelves did not bear the Kitchenaid Logo or frosted scheme on glass shelves (I requested and was informed that the replacement shelves would match my Superbra) - Otherwise, parts, when available, were shipped and arrived in well packaged boxes and not damaged. Parts were cheaper than Kitchenaid, though I would call Kitchenaid first to inquire about matching parts prior to ordering from partselect, if that matters to the buyer...Matching shelves may not in fact be available from manufacturer due to age of appliance.
Read more...
Your Price
$9.43
Ice Chute Door
Second problem was the Chute and chute seal had broken off from the hinge chute so it wouldn't open or close when dispensing ice. Was pretty tricky to realign the chute seal to the hinge, but with some paitence and manipulation, was able to reconnect them.
I am REALLY impressed with the detailed drawings I found on PartSelect.com's website. Without these drawings it would have been difficult for me (my husband and son put the parts in, I did the ordering) to know what parts to order. Service was EXCELLENT. I would definitely do business with this company again. Great work! Read more...
PartSelect Number PS11738536
Manufacturer Part Number WP12562701
This part is the replacement ice chute door for your refrigerator/freezer. It is a round, black part that is approximately 2 ½ inches in diameter. The dispenser ice chute door opens to let ice through when dispensing into a glass or some other container. If the chute door is broken, your refrigerator may not be able to dispense ice properly. Be sure to disconnect the power from your refrigerator before you begin this repair. This part is sold individually and is an authentic OEM part sourced directly from the manufacturer.
Fixes these symptoms
- Ice maker won’t dispense ice
- See more...
Installation Instructions
Janet from Edmonds, WA
Water dispenser got stuck on one function, couldn't get water to work
Removed two screws and took off water dispenser front panel. Unplugged wires to old control board and removed it from brackets holding it to inside of dispenser panel. Aligned and pushed new control (with care to only touch the outside edges of board...cannot touch circuitry which will permanently damage it). Was tricky aligning the board and snapping it back on, but finally got it in place. Repositioned dispenser panel and reattached two screws.Second problem was the Chute and chute seal had broken off from the hinge chute so it wouldn't open or close when dispensing ice. Was pretty tricky to realign the chute seal to the hinge, but with some paitence and manipulation, was able to reconnect them.
I am REALLY impressed with the detailed drawings I found on PartSelect.com's website. Without these drawings it would have been difficult for me (my husband and son put the parts in, I did the ordering) to know what parts to order. Service was EXCELLENT. I would definitely do business with this company again. Great work! Read more...
Your Price
$15.38
Dispenser Grille - Black
PartSelect Number PS11738664
Manufacturer Part Number WP12999301B
This dispenser grille catches any overflow from the ice/water dispenser.
Installation Instructions
Gabriele from Phoenixville, PA
Dispenser Was Damaged In Dishwasher
I just exchanged it, was really easy. Ordering of your well set up internet page was very easy and the part arrived extremely fast price was very competitive. I am very happy with the service provided.
Read more...
Your Price
$143.96
Ice Dispenser Solenoid and Door Kit
PartSelect Number PS2003478
Manufacturer Part Number 12001991
In addition to the solenoid (115V), this kit also comes with a door strike and an ice door assembly. Please be advised the spring and roll pin are not included with this kit.
Fixes these symptoms
- Door Sweating
- Door won’t open or close
- Ice maker not making ice
- See more...
Installation Instructions
Scott from Walker, LA
Ice Dispenser "round chute" broken side tab, ice/water fountain not working
I could see that a tab was broken from the round chute that opens for ice dispensing and closes to seal off freezer ice chute when not in use. With the tab broken, the round door would not shut to seal the freezer chute and dispensing water would spatter everywhere. I looked for just the round door part, but is only sold in the "Ice dispenser solenoid and door kit" I only had to use the round chute/flap from the kit. The instructions were easy to follow and I had the fridge back working in about 10 minutes. It took me longer to find the right star headed screwdriver that I needed to remove the Maytag star screws (5) total. Because I didn't have to replace the solenoid or the spring mechanism, this was especially easy, and now I have those parts on hand if one day I need them!!
Read more...
Your Price
$46.13
Overflow Grille - White
PartSelect Number PS11739625
Manufacturer Part Number WP2206670W
This is a genuine Whirlpool dispenser overflow grille for your refrigerator. This part is made of plastic and snaps in under the water and ice dispensers on your refrigerator door. Its function is to catch drips and spills from the dispenser.
Your Price
$10.76
Ice Chute Seal
2 -Order the ice chute door and seal (seal is rubber and eventually it will stop sealing - while you are in there go ahead and change it)
3 - Unplug the refrigerator then remove the sump tray by pulling it straight out from the door
4 - Unscrew the two screws hidden behind the sump tray - hold the dispenser front housing in place so it doesn't drop downward - after removing the two screws slide the dispenser front housing downward while pressing it against the refrigerator door - there are two clips on the back of the housing that hold it against the refrigerator door
5 - Gently pull the dispenser front housing out of the refrigerator door an inch or two - you will be able to see the electrical connections between the dispenser front housing and the refrigerator.
6 - Continue pulling out the dispenser front housing until you can reach the multi-wire connector on the left - the connector is held together by a clip on the bottom center - squeeze the clip at the end closest to the wires to release it - gently pull the connector off
7 - In the center of the back of the dispenser front housing is a black plastic box (the limit switch) - again, gently pull it away from the two clips holing it on
8 - Set the dispenser front housing aside
9 - Slip the water hose out of the clips holding to to the chute
10 - Unscrew the three screws holding the chute to the door (two on the left and one on the upper right - Slide the chute out of the door
11 - Hold the door hinge so you don't accidentally break it (personal experience) and unclip the top then the bottom of the ice cube door from the hinge (the ice chute seal and ice chute door insulation are attached to the ice cube door - take all three out at the same time)
12 - Slip the ice chute seal off of the ice cube door - pull the ice chute door insulation out of the ice cube door
13 - Put the ice chute door insulation into the new ice chute door - Slip the ice chute seal onto the ice cube door (the schematic will give you the proper orientation for all of the parts)
14 - Again holding the door hinge - slip the two "L" shaped clips onto the bottom of the ice chute door - rotate the ice chute door assembly and snap (gently) the two side clips into place over the opening in the door hinge
15 - Breath a breath of relief if you didn't break anything
16 - Slide the chute assembly over the white pin on the lower right of the refrigerator opening that accepts the chute
17 - Replace the three screws that hold the chute assembly to the door - replace the water line
18 - Clip the limit switch onto the back of the dispenser front housing
19 - run the multi-wire connector behind the water line - connect it to the back of the dispenser front housing
20 - Slip the wires back into the clips along the sides of the opening in the refrigerate door
21 - Rest the dispenser front housing on the bottom of the door opening - it must fit flush to the door (top, bottom and sides) - Slide it gently upward until it stops - replace the two screws at the bottom rear of the dispenser front housing - slide the sump tray back in place
22 - Plug in the refrigerator
23 - Dispense ice cubes into a high ball glass and enjoy a job well done Read more...
PartSelect Number PS11738577
Manufacturer Part Number WP12665101
Installation Instructions
Rocky from ALBANY, IN
The Ice Cube Door Clips Broke
1 - Look at the schematic for the "Fountain" on Partselect.com2 -Order the ice chute door and seal (seal is rubber and eventually it will stop sealing - while you are in there go ahead and change it)
3 - Unplug the refrigerator then remove the sump tray by pulling it straight out from the door
4 - Unscrew the two screws hidden behind the sump tray - hold the dispenser front housing in place so it doesn't drop downward - after removing the two screws slide the dispenser front housing downward while pressing it against the refrigerator door - there are two clips on the back of the housing that hold it against the refrigerator door
5 - Gently pull the dispenser front housing out of the refrigerator door an inch or two - you will be able to see the electrical connections between the dispenser front housing and the refrigerator.
6 - Continue pulling out the dispenser front housing until you can reach the multi-wire connector on the left - the connector is held together by a clip on the bottom center - squeeze the clip at the end closest to the wires to release it - gently pull the connector off
7 - In the center of the back of the dispenser front housing is a black plastic box (the limit switch) - again, gently pull it away from the two clips holing it on
8 - Set the dispenser front housing aside
9 - Slip the water hose out of the clips holding to to the chute
10 - Unscrew the three screws holding the chute to the door (two on the left and one on the upper right - Slide the chute out of the door
11 - Hold the door hinge so you don't accidentally break it (personal experience) and unclip the top then the bottom of the ice cube door from the hinge (the ice chute seal and ice chute door insulation are attached to the ice cube door - take all three out at the same time)
12 - Slip the ice chute seal off of the ice cube door - pull the ice chute door insulation out of the ice cube door
13 - Put the ice chute door insulation into the new ice chute door - Slip the ice chute seal onto the ice cube door (the schematic will give you the proper orientation for all of the parts)
14 - Again holding the door hinge - slip the two "L" shaped clips onto the bottom of the ice chute door - rotate the ice chute door assembly and snap (gently) the two side clips into place over the opening in the door hinge
15 - Breath a breath of relief if you didn't break anything
16 - Slide the chute assembly over the white pin on the lower right of the refrigerator opening that accepts the chute
17 - Replace the three screws that hold the chute assembly to the door - replace the water line
18 - Clip the limit switch onto the back of the dispenser front housing
19 - run the multi-wire connector behind the water line - connect it to the back of the dispenser front housing
20 - Slip the wires back into the clips along the sides of the opening in the refrigerate door
21 - Rest the dispenser front housing on the bottom of the door opening - it must fit flush to the door (top, bottom and sides) - Slide it gently upward until it stops - replace the two screws at the bottom rear of the dispenser front housing - slide the sump tray back in place
22 - Plug in the refrigerator
23 - Dispense ice cubes into a high ball glass and enjoy a job well done Read more...
Your Price
$52.33
Dispenser Grille
PartSelect Number PS11743632
Manufacturer Part Number WP67005636
This drip tray, also known as an overflow grille, is a manufacturer-approved replacement part for your refrigerator. The drip tray catches drips of water from the ice and water dispenser. To replace this part, simply pull out the existing overflow grille, and slide the new one into place.
Installation Instructions
Jeff from Lafayette, LA
Two of the plastic ice/water dispenser hooks were broken from a previous PROFESSIONAL repair and kept falling off.
I ordered a new dispenser and replaced it. It arrived via FEDEX in two days and it took about 10 minutes to replace.
Read more...
Your Price
$46.28
Your Price
$46.01
Related Parts
- All Amana Refrigerator parts
- Amana Refrigerator Brackets and Flanges
- Amana Refrigerator Caps and Lids
- Amana Refrigerator Circuit Boards and Touch Pads
- Amana Refrigerator Compressors
- Amana Refrigerator Doors
- Amana Refrigerator Drawers and Glides
- Amana Refrigerator Drip Bowls
- Amana Refrigerator Ducts and Vents
- Amana Refrigerator Elements and Burners
- Amana Refrigerator Fans and Blowers
- Amana Refrigerator Filters
- Amana Refrigerator Grilles and Kickplates
- Amana Refrigerator Handles
- Amana Refrigerator Hardware
- Amana Refrigerator Hinges
- Amana Refrigerator Hoses and Tubes
- Amana Refrigerator Ice Makers
- Amana Refrigerator Insulations
- Amana Refrigerator Knobs
- Amana Refrigerator Lights and Bulbs
- Amana Refrigerator Motors
- Amana Refrigerator Seals and Gaskets
- Amana Refrigerator Switches
- Amana Refrigerator Thermostats
- Amana Refrigerator Trays and Shelves
- Amana Refrigerator Valves
- Amana Refrigerator Wheels and Rollers
- Amana Refrigerator Wire Plugs and Connectors
