Kenmore Freezer Ice Makers
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Kenmore Freezer Ice Makers
Your Price
$84.62
In Stock
Kenmore Freezer Refrigerator Ice Maker Assembly
PartSelect Number PS12364147
Manufacturer Part Number 241798231
This 8-cube ice maker is used to create ice for your refrigerator. The ice maker receives water from the water inlet valve and will freeze until ice cubes are formed. Once the water has been frozen the cubes will be ejected from the mold in to the ice bucket. The ice maker will continue the process until the ice bucket has reached the limit. If your ice maker is not making ice you may need to replace this part. Please remember to disconnect the power and water supply before starting your repair. This ice maker is a genuine OEM part.
Fixes these symptoms
- Clicking sound
- Ice maker dispenses too little ice
- Ice maker not making ice
- See more...
Installation Instructions
Juan from Miami, FL
Broken ice maker
Unplugged faulty ice maker, removed two screws holding it to the refrigerator and took it out. Reversed the operation with the new ice maker and after a few minutes presto, we have ice.
Read more...
Your Price
$227.76
In Stock
Kenmore Freezer Refrigerator Ice Maker Assembly
PartSelect Number PS3617225
Manufacturer Part Number AEQ72909603
This ice maker assembly is for refrigerators. This Ice maker assembly contains the complete ice maker and housing. The assembly may include multiple parts; refer to your parts diagram for a complete list of parts included.
Fixes these symptoms
- Ice maker not making ice
- Ice maker won’t dispense ice
- See more...
Installation Instructions
Amber from PEORIA, IL
Icemaker quit releasing ice from tray and water was pouring and freezing in ice storage bin
This couldn't have been easier. Two tiny screws in the front needed unscrewed, and then two plastic clips in the middle just had to be popped lose. Finally, you unplugged the power cord. Then, you just needed to reverse the process by plugging the new ice maker in, popping the clips in place, and screwing the two holes back in and turning the whole thing on. Voila! Perfect ice cubes again. And for only a little over $100.
Read more...
Your Price
$96.78
In Stock
Kenmore Freezer Replacement Ice Maker
PartSelect Number PS735469
Manufacturer Part Number 5303918277
This replacement icemaker may also be known as the ice maker assembly and is compatible with your refrigerator/freezer. This assembly replaces the heat-release ice maker unit only. The kit comes with four round female connectors at the end of the wire harness. It also comes with the adaptor that converts the harness to three round female, and one round male connectors. The tools you will need in order to make this installation include a 1/4-inch nut driver, and a Phillips screwdriver. Before starting this repair make sure to unplug your refrigerator and shut off the water supply.
Fixes these symptoms
- Ice maker not making ice
- Ice maker won’t dispense ice
- Leaking
- See more...
Installation Instructions
JACK from MESA, AZ
Ice Maker Stopped Working
It was pretty straight forward. Remove the two screws that hold the unit to the wall of the freezer. In my case, I had to use a different ice maker than what came with the frig. In order to install the replacement unit they sent a wire adaptor so it would attach to the existing wiring. That too was all fine and dandy. The only problem was that the end of the wire adaptor did not fit through the existing hole in the rear of the frig. I used a utility knife to cut through the thin metal lining. That worked just fine. However, I could not cut through the insulation because I could not reach it through the small hole. The excess wire was supposed to be pulled through the hole and out through the back of the unit. So now the excess is between the wall of the freezer and the insulation. The unit is working wonderfully. In fact, it is making more ice than I can use. I am very pleased with the replacement unit. This is the 3rd ice maker that has been in this frig. All the others had a design flaw that had a leak in the rear of the unit. This caused all the ice to form into a big block. The replacement unit has not had this problem so far. Thank you for allowing me to explain my situation so that maybe others may benifit from my experience. Thank you. Jack
Read more...
Your Price
$126.16
In Stock
Kenmore Freezer Ice Maker Assembly With Water Inlet Valve
Attach supply line to water valve with adjustable wrench. Attach water line to ice maker on back of case (twist lock) no tools required.
Attach water line from ice maker to water valve (push connection) no tools required. Attache water valve to case at bottom w/one screw. (nut driver)
Reassemble access cover to bottom of case w/socket wrench (4 screws). Remove plastic cover inside freezer (w/screw driver to release from evap cover) to expose ice maker harness connection. Remove two plastic plugs (carefully w screw driver) exposing screw anchors for mounting Ice maker. Assemble two mounting screws w/nut driver. (Do not dtrive all the way in) Plug ice maker harness to plug on back of evap cover.(no tools required) Place cover over harness connection) no tools required. Guide water fill tube into fill cup on ice maker. (no tools required) Hang ice maker on mounting screws. Level Ice maker and tighten screws. (torpedo level makes it easy if you have one handy. Place Ice bucket under Ice maker on freezer shelf (lower position). Turn ice maker on and you are ready to go. Easy Job!!!! Read more...
PartSelect Number PS10057479
Manufacturer Part Number IM116000
This add-on icemaker assembly is a part for your refrigerator/freezer. The kit includes an icemaker that makes eight radius ice cubes, the water valve, an ice bucket, the fill tube, the harness, and installation instructions. Note: This icemaker assembly will fit most Frigidaire models manufactured from 2001 to present.
Fixes these symptoms
- Ice maker not making ice
- See more...
Installation Instructions
MICHAEL from GEORGETOWN, IN
Bought a new refrigerator. Did not come with an Icemaker.
Remove access cover at bottom of case w/socket wrench (4 screws).Attach supply line to water valve with adjustable wrench. Attach water line to ice maker on back of case (twist lock) no tools required.
Attach water line from ice maker to water valve (push connection) no tools required. Attache water valve to case at bottom w/one screw. (nut driver)
Reassemble access cover to bottom of case w/socket wrench (4 screws). Remove plastic cover inside freezer (w/screw driver to release from evap cover) to expose ice maker harness connection. Remove two plastic plugs (carefully w screw driver) exposing screw anchors for mounting Ice maker. Assemble two mounting screws w/nut driver. (Do not dtrive all the way in) Plug ice maker harness to plug on back of evap cover.(no tools required) Place cover over harness connection) no tools required. Guide water fill tube into fill cup on ice maker. (no tools required) Hang ice maker on mounting screws. Level Ice maker and tighten screws. (torpedo level makes it easy if you have one handy. Place Ice bucket under Ice maker on freezer shelf (lower position). Turn ice maker on and you are ready to go. Easy Job!!!! Read more...
Your Price
$184.23
In Stock
Kenmore Freezer Ice Maker Assembly - 6 Wire
PartSelect Number PS7788173
Manufacturer Part Number AEQ73110205
This ice maker assembly kit is a genuine OEM replacement designed for select LG refrigerators. Engineered to produce ice efficiently, it features a built-in thermostat and heating element that work together to freeze water and release ice cubes from the mold. With a capacity to produce up to 14 cubes per cycle, this assembly ensures a consistent and reliable supply of ice. Installation is straightforward and suitable for DIY repairs, though model compatibility should be verified prior to purchase. Crafted to meet LG’s performance standards, this kit offers dependable operation and long-term durability.
Fixes these symptoms
- Ice maker not making ice
- Ice maker won’t dispense ice
- See more...
Installation Instructions
Ron from MAXWELL, IN
old one broke
Sent for replacement,got it took old one off put new one on that was it. Thank you
Read more...
Your Price
$278.83
In Stock
Kenmore Freezer Ice Maker Assembly
1. Go behind refrigerator and unplug electrical cord and turn off water supply.
2. In freezer locate electrical plug for ice maker. It has two tabs on the left and right side of it. Lift the tabs and pull the plug to disconnect it.
3. Remove the three screws, 2 on top and 1 on bottom of ice maker You can actually leave the screws in place if you loosen them sufficiently and lift the ice maker off of the screws and washers.
4. Install the new ice maker using the screws and plastic washers to secure it.
5. Plug the electrical connector for ice maker into the receptacle. Note: The plug only goes one way and is keyed with different shaped plugs and holes. The wires on my plug naturally fell upside down so I had to turn the plug 180 degrees to make it fit in the slot.
6. Turn on water and check for leaks.
7. Plug back in refrigerator and you should have ice in less than 12 hours. Read more...
PartSelect Number PS7785531
Manufacturer Part Number 5989JA0002Y
This ice maker assembly is designed for select LG refrigerators and includes both the ice mold and control device to ensure consistent and efficient ice production. If your refrigerator is no longer producing ice, this complete unit may be the solution. Before beginning installation, disconnect the appliance from all utilities and follow safety precautions. Please verify compatibility with your model, as part dimensions may vary slightly.
Fixes these symptoms
- Ice maker not making ice
- See more...
Installation Instructions
Eric from SURPRISE, AZ
The ice maker in freezer P/NO 5988JA0002Y would leak water and make giant ice block
I ordered and replaced the ice maker. To replace:1. Go behind refrigerator and unplug electrical cord and turn off water supply.
2. In freezer locate electrical plug for ice maker. It has two tabs on the left and right side of it. Lift the tabs and pull the plug to disconnect it.
3. Remove the three screws, 2 on top and 1 on bottom of ice maker You can actually leave the screws in place if you loosen them sufficiently and lift the ice maker off of the screws and washers.
4. Install the new ice maker using the screws and plastic washers to secure it.
5. Plug the electrical connector for ice maker into the receptacle. Note: The plug only goes one way and is keyed with different shaped plugs and holes. The wires on my plug naturally fell upside down so I had to turn the plug 180 degrees to make it fit in the slot.
6. Turn on water and check for leaks.
7. Plug back in refrigerator and you should have ice in less than 12 hours. Read more...
Your Price
$236.09
In Stock
Kenmore Freezer Ice Maker Assembly
PartSelect Number PS3532293
Manufacturer Part Number AEQ36756901
This refrigerator ice maker assembly kit is a complete unit designed to provide a consistent and reliable supply of ice. It includes the ice maker, housing, and integrated control mechanism, ensuring full functionality and seamless integration into compatible refrigerator models. The unit receives water, freezes it, and automatically ejects ice into the storage bin, supporting continuous ice production. Constructed from durable materials and engineered for long-term performance, this replacement part helps restore efficient ice-making capabilities. Ideal for resolving issues such as inconsistent ice supply or a non-functioning ice maker, it offers a dependable solution for maintaining convenience in daily use.
Fixes these symptoms
- Ice maker not making ice
- Ice maker won’t dispense ice
- See more...
Installation Instructions
John from HILLSBORO, OR
Ice maker bail frozen. Chose to replace the entire assembly
Examined old ice maker. It is held by some Philips screws. There are many screws you don't need to unscrew so look carefully. Then disconnected th dual in line connector. There is a little push tab to squeeze to release. Then the ground is connected with a screw. It's a little hard to see but unscrew that. My replacement came with no instructions or screws so try not to drop the screws down in the netherlands of the fridge. The hardest part was maneuvering the icemaker to reattach the power and ground. Even with that pretty straight forward replacement.
Read more...
Your Price
$62.60
In Stock
Kenmore Freezer Bucket Ice
PartSelect Number PS12582351
Manufacturer Part Number MKK61842202
This ice bucket is a genuine replacement part designed to collect and store ice produced by the freezer’s ice maker. Located inside the freezer compartment, typically in a pull-out drawer beneath the ice maker, it ensures proper ice dispensing and organization. Over time, the original bin can become cracked, warped, or broken, leading to dispensing issues. Replacing it restores full functionality and helps maintain efficient ice production. Installation is simple—remove the old bin and slide the new one into place for a secure fit.
Your Price
$35.15
In Stock
Kenmore Freezer Drive Gear
PartSelect Number PS2349843
Manufacturer Part Number 5304469403
The ejector drive gear is a part for your refrigerator. This icemaker drive gear is for the ejector blades. The part rotates the cube ejector arm, which cycles the icemaker and pushes the cubes out and into the ice bucket, ready for the ice to be used. The outside diameter of this piece is almost two inches by two inches. The reason for needing to replace your gear is if the current one is broken/missing a tooth, or if your icemaker is not dispensing ice and is noisy.
Fixes these symptoms
- Ice maker not making ice
- Ice maker won’t dispense ice
- See more...
Your Price
$128.53
In Stock
Kenmore Freezer Icemaker Assembly
The icemaker is making ice now. Read more...
PartSelect Number PS1533004
Manufacturer Part Number 5304458371
Designed to deliver reliable, automatic ice production, this genuine OEM ice maker assembly restores full ice-making functionality within your refrigerator or freezer. It receives water from the inlet valve, freezes it in the internal mold, and efficiently releases formed ice into the storage bin for convenient use. Built as a complete unit with integrated components for a seamless fit, it provides dependable performance and easy installation. Ideal for replacing a faulty or non-producing ice maker, it helps restore consistent ice output and smooth, everyday operation.
Fixes these symptoms
- Ice maker not making ice
- Ice maker won’t dispense ice
- Leaking
- See more...
Installation Instructions
Brenda from Sanford, FL
Did not make ice
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Then I took the new icemaker out of the box and reversed the procedure. The icemaker is making ice now. Read more...
Related Kenmore Freezer Parts
- All Kenmore Freezer parts
- Kenmore Freezer Brackets and Flanges
- Kenmore Freezer Caps and Lids
- Kenmore Freezer Circuit Boards and Touch Pads
- Kenmore Freezer Compressors
- Kenmore Freezer Dispensers
- Kenmore Freezer Doors
- Kenmore Freezer Drawers and Glides
- Kenmore Freezer Drip Bowls
- Kenmore Freezer Electronics
- Kenmore Freezer Elements and Burners
- Kenmore Freezer Fans and Blowers
- Kenmore Freezer Filters
- Kenmore Freezer Fuses
- Kenmore Freezer Grilles and Kickplates
- Kenmore Freezer Handles
- Kenmore Freezer Hardware
- Kenmore Freezer Hinges
- Kenmore Freezer Hoses and Tubes
- Kenmore Freezer Knobs
- Kenmore Freezer Latches
- Kenmore Freezer Lights and Bulbs
- Kenmore Freezer Manuals and Literatures
- Kenmore Freezer Motors
- Kenmore Freezer Panels
- Kenmore Freezer Seals and Gaskets
- Kenmore Freezer Sensors
- Kenmore Freezer Switches
- Kenmore Freezer Thermostats
- Kenmore Freezer Touch-Up Paint
- Kenmore Freezer Trays and Shelves
- Kenmore Freezer Trims
- Kenmore Freezer Valves
- Kenmore Freezer Wheels and Rollers
- Kenmore Freezer Wire Plugs and Connectors