My Orders
Kenmore Freezer Valves
GET YOUR OFFICIAL Kenmore PARTS TO ENSURE VICTORY
Popular Kenmore Freezer Valves
If you notice that the ice maker in your refrigerator is leaking or is not making or dispensing ice, you may need to replace the water inlet valve. When energized, the water inlet valve releases water from the supply line into the ice mold. The water inlet valve is in the back of your refrigerator so you will need to pull the fridge out from the wall before completing this repair. To complete this job, you will need a 1/2 inch wrench, a 1/4 inch nut driver and a utility knife. If your old inlet valve has a screw-in fitting, you may need to simply cut the end of the hose to fit in the new part. Be sure to disconnect both the water and power supply from the refrigerator prior to beginning this repair.
If you notice that the ice maker in your refrigerator is leaking or is not making or dispensing ice, you may need to replace the water inlet valve. When energized, the water inlet valve releases water from the supply line into the ice mold. The water inlet valve is in the back of your refrigerator so you will need to pull the fridge out from the wall before completing this repair. To complete this job, you will need a 1/2 inch wrench, a 1/4 inch nut driver and a utility knife. If your old inlet valve has a screw-in fitting, you may need to simply cut the end of the hose to fit in the new part. Be sure to disconnect both the water and power supply from the refrigerator prior to beginning this repair.
Installation Instructions
Orville from Garland, TX
Was not filling the ice tray full.
I had put in a new ice maker and it still had the problem, (I needed the Ice maker anyway) I installed the vale and while I was at it I put a five year filter on the water line that went from the value to the Ice maker, it took less than one hours, the ice is making like it did when it was new, I could not be more please at theis time. Th
... Read more
anks for your Interest. God bless.
Read less
This includes the primary and secondary valves along with the wire harness.
This includes the primary and secondary valves along with the wire harness.
Installation Instructions
Richard from JACKSONVILLE, FL
replace leaking water inlet valve assembly
1. Shut off water to refrigerator. 2. Removed bottom sheet metal cover (6 screws). 3. Removed leaking water inlet valve assembly from refrigerator (1 screw). 4. Remove water inlet tube (loosen nut) and tube back to refrigerator (pull from water valve after remove cotter pin washer). 5. Detach two electrical wire harnesses. 6. Install new
... Read more
water inlet valve assembly to refrigerator (1 screw). 7. Replace both water tubes to water inlet assembly. 8. Re-attach both wiring harnesses. 9. Turn water to refrigerator on. 10. Check for leaks. 11. Re-attach bottom sheet cover (6 screws).
Read less
This is a water inlet valve which is used in washing machines. The valve controls and monitors the flow of water into the washer. It has a multi-mount bracket and outlet adaptor. The tools needed for this repair are: a 5/16 nut driver, 1/4 nut driver, and a small flat blade screwdriver. If cold water does not flow into washer, or the washing machine will not fill with hot water, replacing the valve can be the solution. To gain access to the water valve, locate the back of the washer and remove the hot and cold hoses, as well as the whole assembly. Next, remove the four wires and loosen up the clamp. After removing the old valve, replace it with the new one and reconnect the wires and hose. Remember to disconnect the washer from the power source before starting this project.
This is a water inlet valve which is used in washing machines. The valve controls and monitors the flow of water into the washer. It has a multi-mount bracket and outlet adaptor. The tools needed for this repair are: a 5/16 nut driver, 1/4 nut driver, and a small flat blade screwdriver. If cold water does not flow into washer, or the washing machine will not fill with hot water, replacing the valve can be the solution. To gain access to the water valve, locate the back of the washer and remove the hot and cold hoses, as well as the whole assembly. Next, remove the four wires and loosen up the clamp. After removing the old valve, replace it with the new one and reconnect the wires and hose. Remember to disconnect the washer from the power source before starting this project.
Installation Instructions
Brian from El Cajon, CA
Cold water valve only opened to a trickle
I started by unplugging the appliance and then shut off the hot and cold water faucets then I disconnected and drained the hoses. Next, I removed the two screws that held the valve assembly in place. I then pulled the assembly out about 3 inches and disconnected the two wire plugs. The last step was to loosen the hose clamp on the outl
... Read more
et hose and pull off the outlet hose. I reversed the steps to install the new assembly and the total repair took about 10 minutes.
Read less
Installation Instructions
Nancy from NEW ALBANY, IN
Our refrigerator was not dispencing water or ice.
Turned of water to refrigerator and unplugged refrigerator. Removed the water line from refrigerator. Removed back panel. Removed mounting screw from the water valve, Unhooked wire harness from valve and removed the water line on back of valve. Reconnected wiring harness to new valve, reconnected water line on back of valve. Replaced the
... Read more
back panel to refrigerator and put the water line back on the new valve. Turned on water valve and checked for leaks. It's now dispensing water and ice.
Read less
Installation Instructions
shirley from FLORISSANT, MO
Ice maker not working but making a sound when turned on (buzzing). Water valve not functioning when tested with a multitester (multimeter).
I removed the old water valve, disconnected the water tube going in and tube going out to the back of the refrigerator. New water valve bracket different than the previous one which resulted in my having to modify it to fit. Not an easy task as it was preformed metal. Once hooked up, water turned on, and ice maker turned on, the sound
... Read more
I'm getting now is clunking and not making ice. My debate is whether or not to purchase a new ice maker or revert to the tried and true method with ice trays which work every time.
Read less
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
This water inlet valve is a genuine replacement component designed to regulate the flow of water to both the ice maker and water dispenser in select refrigerator models. It ensures a steady and controlled supply of water, supporting consistent ice production and reliable dispensing. If the valve is faulty, symptoms may include no ice production, a non-functioning water dispenser, water leaks near the valve, or unusual noises during operation. Replacing the valve can restore proper performance and improve overall efficiency. Installation should be performed with the appliance unplugged or the water supply turned off. Always verify compatibility with your specific model before installation.
This water inlet valve is a genuine replacement component designed to regulate the flow of water to both the ice maker and water dispenser in select refrigerator models. It ensures a steady and controlled supply of water, supporting consistent ice production and reliable dispensing. If the valve is faulty, symptoms may include no ice production, a non-functioning water dispenser, water leaks near the valve, or unusual noises during operation. Replacing the valve can restore proper performance and improve overall efficiency. Installation should be performed with the appliance unplugged or the water supply turned off. Always verify compatibility with your specific model before installation.
This part is a solenoid-operated switch located at the bottom of the refrigerator. When the water inlet valve is turned on, water is released from the supply line through the water valve and into the compact icemaker mold. The kit includes the mounting hardware and bracket plastic tubing fittings. The retaining nut must be cut off the plastic water line and gently pushed into the new valve. To remove, press down on the ring that the tube slides into. Refer to the installation instructions for further guidance. Please note: the manufacturer has redesigned this part and it can appear different than the original. It has a new quick connection.
This part is a solenoid-operated switch located at the bottom of the refrigerator. When the water inlet valve is turned on, water is released from the supply line through the water valve and into the compact icemaker mold. The kit includes the mounting hardware and bracket plastic tubing fittings. The retaining nut must be cut off the plastic water line and gently pushed into the new valve. To remove, press down on the ring that the tube slides into. Refer to the installation instructions for further guidance. Please note: the manufacturer has redesigned this part and it can appear different than the original. It has a new quick connection.
Installation Instructions
Kevin from Boston, MA
no water getting to ice maker
The ice maker had been slowly dying and one day just stopped making ice. No water was getting to the trays.
I read that this could be caused by a failure of the valve, even though the continuity test indicated that the solenoid was okay.
I ordered the part Friday afternoon. It was delivered Saturday. I did the repai ... Read more r in 10 minutes.
I pulled the fridge away from the wall.
I unplugged the fridge. I closed the water supply valve.
I unscrewed the two mounting screws using a flat head screwdriver.
I pulled the old valve out from refrigerator.
Using an adjustable wrench I detached the water supply from the valve. I detached the hose leading to the ice maker from the valve.
I pulled the electrical connectors from the connectors on the valve.
I attached the hoses to the new valve, attached the electrical connector, screwed the new valve in its place, opened the water supply, plugged the fridge back in, checked for leaks, and waited for a few hours.
My ice maker is working better than it has in at least two years.
I read that this could be caused by a failure of the valve, even though the continuity test indicated that the solenoid was okay.
I ordered the part Friday afternoon. It was delivered Saturday. I did the repai ... Read more r in 10 minutes.
I pulled the fridge away from the wall.
I unplugged the fridge. I closed the water supply valve.
I unscrewed the two mounting screws using a flat head screwdriver.
I pulled the old valve out from refrigerator.
Using an adjustable wrench I detached the water supply from the valve. I detached the hose leading to the ice maker from the valve.
I pulled the electrical connectors from the connectors on the valve.
I attached the hoses to the new valve, attached the electrical connector, screwed the new valve in its place, opened the water supply, plugged the fridge back in, checked for leaks, and waited for a few hours.
My ice maker is working better than it has in at least two years.
Read less
This water inlet valve is a genuine replacement part that controls the flow of water to your refrigerator’s ice maker and dispenser, helping ensure steady ice production and proper dispensing. It features a single-valve design with an attached wire harness and is used to replace a valve that may be leaking, failing to supply water, or causing slow ice and water output. Installing a new valve helps restore smooth, reliable operation. Be sure to disconnect power and the water line before replacing the part, and check your refrigerator’s model number to confirm the correct fit.
This water inlet valve is a genuine replacement part that controls the flow of water to your refrigerator’s ice maker and dispenser, helping ensure steady ice production and proper dispensing. It features a single-valve design with an attached wire harness and is used to replace a valve that may be leaking, failing to supply water, or causing slow ice and water output. Installing a new valve helps restore smooth, reliable operation. Be sure to disconnect power and the water line before replacing the part, and check your refrigerator’s model number to confirm the correct fit.
Installation Instructions
William from NEWPORT NEWS, VA
The ice maker fill valve died.
Went on line to see how difficult it would be to replace the valve. Through Google there was a video which showed in exact detail how to remove and replace the valve. Then went on line to find the replacement part which was readily available. The only problem was that the connection on the valve where the fill water enters the valve was l
... Read more
arger than the old valve. To fix that I went to a local Ace hardware store and found a nut that would fit the valve connection. Also don't forget to use a compression ring to keep the fill line secured when replaced.
Over all it was very simple and was in my "pay grade"
Over all it was very simple and was in my "pay grade"
Read less
Please note plastic tube is sold separately.
Please note plastic tube is sold separately.