Kenmore Freezer Caps and Lids
Find your part
Enter your model number or a part number and click "Search"
Popular Kenmore Freezer Caps and Lids
Interior Drain Plug
PartSelect Number PS426014
Manufacturer Part Number 216502600
This is a plastic OEM drain plug that is attached to the drain system of your appliance and is compatible with several different makes and models of refrigerators, freezers, and air conditioners. This drain plug is used to prevent water from leaking out of the incorrect drain system within the appliance and is normally removed for cleaning and maintenance. If you notice water leaking inside of your appliance, the plug may be improperly positioned or may need replacing. To replace, simply pull off the damaged plug and insert the new plug in its place.
Installation Instructions
paul from LISLE, IL
While defrosting freezer tossed the drain plug with ice and water into the sewer system.
Opened mailer and bag and place the drain plug into the drain. fit perfectly. In fact it is better than the one lost since the original needed a screwdriver or tool to remove the plug. This one has a flang or finger turner on it so that it can be removed. Also, does not interfere with items in bottom of freezer.
Read more...
Drain Plug
PartSelect Number PS977294
Manufacturer Part Number 297013600
Installation Instructions
Barbara from Shaker Heights, OH
Manual Defrost-Extreme heat caused ice build-up
Defrosted freezer, hose broke due to dry-rot. Used towels to let water drain into pan. Now with the plug minimal frost build-up. No ice at all. Now if I could get a new hose to drain the water that would be great.
Read more...
Your Price
$9.52
In Stock
Hinge Sleeve Hole Plug - White
PartSelect Number PS11739707
Manufacturer Part Number WP2212648
Sold individually.
Installation Instructions
william from williamstown, NJ
bottom hinge on refrigm door squeaked
removed all items stored on door,removed screws holding bottom hinge to frame, placed door on floor while cleaning bottom of door, placed washer on hinge, reinstalled door on fridge, placed hinge on frame and secured with screws.
Read more...
Shelf End Cap - Right Side - Tilt-out
PartSelect Number PS426051
Manufacturer Part Number 216514000
Installation Instructions
wissam farhat from medley, FL
End cap for side door shelf broken
Both end caps were missing on the door side bottom metal shelf. succesfully installed no tools needed
Read more...
Terminal Cover
PartSelect Number PS11738947
Manufacturer Part Number WP2162358
This is a terminal cover for the compressor in a refrigerator. This covers the relay and overload switch on the compressor. Once you have gained access to the terminal cover, you will see that the cover is held on by a tension or retaining clip. Simply pop the cover off and replace with the new cover. The cover is made of plastic and is black in color. It measure less than 3 inches long and less than 3 inches wide. This is a genuine replacement part from the original manufacturer.
Door Hinge Cover
The end cap kit went in rather straightforwardly; the visual drawing in the part envelope was sufficient.
The glass shelf was only slightly more of a problem as I did not realize that a back piece could be pulled off (minor effort), the new glass placed in position, and then the back clamping piece placed over the rear of the bracket, clamping the glass.
Couldn't have been simpler and saved quite a bit of money if a repair person would have had to come out, first to provide an estimate, and then, the actual repairs; probably two hour minimum. :-) Read more...
PartSelect Number PS316229
Manufacturer Part Number 1119787
Installation Instructions
Michael from Albuquerque, NM
Movers broke a glass shelf, cracked a cover, and an end-cap
The old cover came off in two pieces (broken) and the new cover, rather than screwing on, simply snapped in place - a huge improvement over original part.The end cap kit went in rather straightforwardly; the visual drawing in the part envelope was sufficient.
The glass shelf was only slightly more of a problem as I did not realize that a back piece could be pulled off (minor effort), the new glass placed in position, and then the back clamping piece placed over the rear of the bracket, clamping the glass.
Couldn't have been simpler and saved quite a bit of money if a repair person would have had to come out, first to provide an estimate, and then, the actual repairs; probably two hour minimum. :-) Read more...
Related Parts
- All Kenmore Freezer parts
- Kenmore Freezer Brackets and Flanges
- Kenmore Freezer Circuit Boards and Touch Pads
- Kenmore Freezer Compressors
- Kenmore Freezer Drawers and Glides
- Kenmore Freezer Electronics
- Kenmore Freezer Grilles and Kickplates
- Kenmore Freezer Handles
- Kenmore Freezer Hardware
- Kenmore Freezer Hinges
- Kenmore Freezer Hoses and Tubes
- Kenmore Freezer Ice Makers
- Kenmore Freezer Lights and Bulbs
- Kenmore Freezer Motors
- Kenmore Freezer Panels
- Kenmore Freezer Seals and Gaskets
- Kenmore Freezer Sensors
- Kenmore Freezer Switches
- Kenmore Freezer Thermostats
- Kenmore Freezer Trays and Shelves
- Kenmore Freezer Valves
- Kenmore Freezer Wire Plugs and Connectors