Kenmore Dishwasher Hinges

Popular Kenmore Dishwasher Hinges

Your Price
$33.09
  In Stock
Kenmore Dishwasher Door Balance Link Kit
★★★★★
★★★★★
202 Reviews
PartSelect Number PS972325
Manufacturer Part Number 8194001
This part is a door balance link kit, also sometimes known as door cable or door spring cable kit, that helps support the door as it opens and closes by connecting to the dishwasher door hinges. The kit includes two door balance links and two door balance mounts with wheels, which will replace both the left and right sides. The only tool needed is a 5/16 nut driver. Before removing the existing kit, take note of how the door balance link kit is assembled for a smooth replacement process. It is recommended to check the door springs in case they need to be replaced as well.
Fixes these symptoms
  • Door latch failure
  • Door won’t close
  • Leaking
  • See more...
Installation Instructions
Scott from Fort Lauderdale, FL
Replaced Hinge Link
Pulled dishwasher from under counter, attached link to spring, hooked spring back into frame/chassis, threaded link through pulleys, attached other end of link onto door, reinstalled dishwasher under counter. All's well. Note-I purchased an extra link anticipating that the other one will fail. They're cheap enough. Read more...
Your Price
$17.88
  In Stock
Kenmore Dishwasher Hinge Cable
★★★★★
★★★★★
27 Reviews
PartSelect Number PS3524406
Manufacturer Part Number 4933DD3001B
This dishwasher door hinge cable assembly connects the door to the spring. The door hinge cable and the door spring apply tension to the door to prevent it from dropping open too quickly. This part contains two plastic pieces which are approximately 2 inches in length by 3/4-inch in width, as well as a rope portion that measures approximately 8 inches in length. When beginning this repair, be sure to use caution when replacing the door hinge cable. The spring to which the door hinge cable attaches is under tension and could snap. This part is sold individually.
Fixes these symptoms
Installation Instructions
Charles from DENNIS, MA
Dishwasher door became heavy and would fall to the floor if you didn't hold it up.
Removed mounting screws from sides of disher. Removed broken piece of connector assy still attached to hinge. Attached new connector assy to hinge then looped it around pulley with spring attached to opposite end. Need both hands to pull spring up to side of tub and connect it. I would suggest replacing both connector assemblies while you have the dishwasher pulled out. Push dishwasher back in and mount with screws. Read more...
Your Price
$7.49
  In Stock
Kenmore Dishwasher Friction Sleeve
★★★★★
★★★★★
34 Reviews
PartSelect Number PS11745488
Manufacturer Part Number WP8268961
This part helps to keep your door quiet when it opens and closes.
Fixes these symptoms
  • Door latch failure
  • Door won’t close
  • Noisy
  • See more...
Installation Instructions
Arthur from YORKTOWN HTS, NY
Door will fall down after opening
unscrewed dishwasher from cabinet ...,moved out slightly....while door closed ...reached with long nosed pliers door spring pulled forward...and allowing white plastic part that fits through sleeve and fit new sleeve over it...pulled spring attaching white plastic part and pushed unit back to cabinet and replaced screws DONE. Read more...
Your Price
$8.54
  In Stock
Kenmore Dishwasher Hinge Arm Link
★★★★★
★★★★★
9 Reviews
PartSelect Number PS259336
Manufacturer Part Number WD14X10009
The hinge link on your dishwasher connects the spring to the dishwasher door hinge. If the hinge link becomes cracked or damaged, you may not be able to shut or lock your dishwasher door properly. In this case, you will need to replace the hinge link. Pull out your dishwasher to inspect the hinge and spring, if the link is broken, it may be disconnected and on the ground already. If not, you can remove the hinge arm link by simply disconnecting it from the hinge and spring, then replacing it with the new part. The hinge arm link is a small piece of white plastic about an inch and a half long. It is sold individually, and is an OEM part from the manufacturer.
Fixes these symptoms
Installation Instructions
Margaret from Meridian, MS
plastic hinge arm link broke causing door to flop open
First I had to unscrew screws under the counter then pulled built in dishwasher out from under the counter, attached hing arm link to right side bracket on door, and the other end I attatched to a spring at the back of the unit. Thats it! and pushed the dishwasher back into place. All back to normal....by the way Im a 67 yr old great grandmother... Read more...
Your Price
$13.01
  In Stock
Kenmore Dishwasher Door Cable
★★★★★
★★★★★
2 Reviews
PartSelect Number PS8727128
Manufacturer Part Number 00610087
This door cable is for dishwashers. Door cable helps balance and support the weight of the door as it opens and closes.
Fixes these symptoms
Your Price
$31.41
  In Stock
Kenmore Dishwasher Spring Linkage
★★★★★
★★★★★
2 Reviews
PartSelect Number PS420766
Manufacturer Part Number 154325201
This linkage attaches to the door spring.
Fixes these symptoms
Installation Instructions
Michael from Redmond, WA
One of the door tension springs and related plastic clip failed causing door to open under full weight
Per the recommendation from PartSelect.com, I purchased 2 new springs and 2 new clips - one set for each side. With the bottom cover plate removed below the door, I removed the remaining spring and clip and installed the 2 new springs and clips by hand. The door now opens with resistance and won't even stay completely opened unless the lower dishwasher tray is rolled out on it. it's like new.
This is the second repair to this dishwasher. Last year I replaced the door latch that had broken with a replacement purchased from partselect.com. That repair was also quite easy.
PartSelect's full part brochures by model made identifying the needed parts simple, and the replacement a breeze.
I even repaired my refrigerator ice maker a couple months ago after purchasing a new control module, and saving both a service fee and the probable full price for a new ice maker.
I've repaired my electric clothes dryer too, and hadn't even thought about all the repairs I'd done thanks to this website, until I told the story of my dishwasher.
I've probably saved $1000 already. Wow!
I love this site.
Read more...
Your Price
$25.94
  In Stock
Kenmore Dishwasher Door Cable and Eyelet
★★★★★
★★★★★
14 Reviews
PartSelect Number PS263918
Manufacturer Part Number WD7X14
This part is sold individually. It is recommended that both sides are changed when replacing one.
Fixes these symptoms
Installation Instructions
Karthik from Springfield, VA
Dishwasher door became really heavy to operate
Note: This procedure assumes replacement of both eyelet cables. It is recommended that both eyelet cables be replaced at the same time.

1. Using a Philips' head screwdriver, remove the four screws holding the lower front panel (below dishwasher door).
2. Remove the faulty eyelet cable(s) hooked into the springs at one end and the door hinges at the other.
3. Take the new eyelet cables and hook them onto the door hinge on either side. Ensure a secure fit.
4. Guide the eyelet cable around the spinwheel on one side and insert the hooks of the springs into the eyelets.
5. Pull on the springs and insert their hooks into the eyelets of the other cable, ensuring a secure fit.
6. Test the door by opening and closing it a few times to ensure the spring has tension.
7. Replace the lower front panel cover removed in step 1 with its screws.
Read more...
Your Price
$139.03
  In Stock
Kenmore Dishwasher Door Hinge - Right Side
PartSelect Number PS11746183
Manufacturer Part Number WP8534853
Fixes these symptoms
Installation Instructions
Tom from UNION GROVE, WI
A small water leak at door
After replacing broken door cables I had a small leak at the door corner. I replaced door seal with that not fixing the leak and found that the door hinges were bent a little from the cables being broke for awile. Installed new hinges and leak is fixed now. A little difficult but once unit was pulled out about 6 inches the hinges were not bad to replace Read more...
Your Price
$24.82
  In Stock
Kenmore Dishwasher Mount
★★★★★
★★★★★
1 Review
PartSelect Number PS11748211
Manufacturer Part Number WPW10084086
Your Price
$75.12
  In Stock
Kenmore Dishwasher Hinge Bushing
★★★★★
★★★★★
1 Review
PartSelect Number PS11745491
Manufacturer Part Number WP8268990

Related Kenmore Dishwasher Parts