My Orders
Kenmore Dishwasher Pumps
GET YOUR OFFICIAL Kenmore PARTS TO ENSURE VICTORY
Popular Kenmore Dishwasher Pumps
This circulation pump is a genuine OEM replacement part designed for use in dishwashers. It is responsible for circulating water throughout the dishwasher during the wash and rinse cycles. The circulation pump draws water from the dishwasher tub, pressurizes it, and then distributes it to the spray arms, which spray the water onto the dishes to remove food particles and debris. The circulation pump may fail due to several reasons such as an electrical fault, a blockage in the pump impeller, motor failure, or physical damage. A faulty pump will result in water leakages, unusually loud noises during use, reduced water circulation, and poor cleaning performance.
This circulation pump is a genuine OEM replacement part designed for use in dishwashers. It is responsible for circulating water throughout the dishwasher during the wash and rinse cycles. The circulation pump draws water from the dishwasher tub, pressurizes it, and then distributes it to the spray arms, which spray the water onto the dishes to remove food particles and debris. The circulation pump may fail due to several reasons such as an electrical fault, a blockage in the pump impeller, motor failure, or physical damage. A faulty pump will result in water leakages, unusually loud noises during use, reduced water circulation, and poor cleaning performance.
Installation Instructions
Samoil from COOPER CITY, FL
The dish washer wasn’t cleaning dishes
The circulation pump is a super easy fix and the installation video parts select has on its website is accurate. I felt the most difficult part of the repair was removing the dishwasher from the kitchen counter to make the repairs. After you get the dishwasher out, you pretty much just pop the old pump out with your hands and a flat head
... Read more
screwdriver. (The supplied video is spot on ) Installing the new pump will require a pinch plier or a hose clamp. I chose a new hose clamp as it is cheaper and I would never use the pinch pliers after this job.
Read less
This drain pump is used in dishwashers to remove water from the dishwasher tub. If the impeller in the dishwasher is damaged or the motor has been shorted out and will not drain, it is possible the body is cracked, causing leakage. To prevent this from happening, replace the drain pump. The tools needed for this installation are: Phillips screwdriver, 5/16 inch nut driver, 5/8 inch wrench, and a flathead screwdriver. Remember to unplug your dishwasher from the power source before beginning this installation project. Refer to the manual provided by the manufacturer for further installation instructions.
This drain pump is used in dishwashers to remove water from the dishwasher tub. If the impeller in the dishwasher is damaged or the motor has been shorted out and will not drain, it is possible the body is cracked, causing leakage. To prevent this from happening, replace the drain pump. The tools needed for this installation are: Phillips screwdriver, 5/16 inch nut driver, 5/8 inch wrench, and a flathead screwdriver. Remember to unplug your dishwasher from the power source before beginning this installation project. Refer to the manual provided by the manufacturer for further installation instructions.
Installation Instructions
Andrew from Alexandria, VA
dishwasher not draining after wash cycle
Caviat: The actual repair is less than 15 minutes, but I spent a lot of time playing with it before I figured out it was that easy and fast. You don't need to remove the dishwasher from the counter to do this. And it will probably help to look at the new part closely so you can understand where the retainer clip is to press it and release
... Read more
the old pump.
First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done.
First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done.
Read less
The pump motor delivers water to the spray arms to clean the dishes during the wash cycle.
The pump motor delivers water to the spray arms to clean the dishes during the wash cycle.
What this part fixes:
- Not cleaning dishes properly
- Not draining
- Will not fill with water
If your dishwasher isn’t draining properly or leaving water behind, this drain pump motor assembly might be the fix you need. It helps clear water from the tub during the drain cycle, keeping your appliance running smoothly and your dishes clean. This genuine replacement part is made to fit a variety of models from Whirlpool and related brands like Kenmore, KitchenAid, and Amana, making installation straightforward and dependable.
If your dishwasher isn’t draining properly or leaving water behind, this drain pump motor assembly might be the fix you need. It helps clear water from the tub during the drain cycle, keeping your appliance running smoothly and your dishes clean. This genuine replacement part is made to fit a variety of models from Whirlpool and related brands like Kenmore, KitchenAid, and Amana, making installation straightforward and dependable.
Installation Instructions
Kelli from BURLINGTON, MA
Dish washer would not drain properly
Shut off breaker. Took off front skirt of dishwasher .
Used pliers to loosen the pressure clamp on drain pump , have towel handy as there will be some water. Turn pump to left as you push in on the clip on side of drain pump. It will come out. Remove wire plug from old pump and plug into new pump than insert new pump and turn an ... Read more d push in till it clicks. Use pliers to pinch hose clamp and push hose onto pump release hose clamp. Turn breaker on. Run a cycle and make sure all is tight before putting skirt on front.
Used pliers to loosen the pressure clamp on drain pump , have towel handy as there will be some water. Turn pump to left as you push in on the clip on side of drain pump. It will come out. Remove wire plug from old pump and plug into new pump than insert new pump and turn an ... Read more d push in till it clicks. Use pliers to pinch hose clamp and push hose onto pump release hose clamp. Turn breaker on. Run a cycle and make sure all is tight before putting skirt on front.
Read less
This is a drain pump assembly for various compatible models of dishwashers, that is responsible for draining the water from the dishwasher after every cycle. This drain pump assembly is made of plastic and fits within the sump assembly, which controls the flow of water into the drain. This drain pump assembly is a genuine OEM part and is made of a high-quality plastic but is sold as an individual component without any other parts, like its drain pump check ball which works within the pump to prevent water from backwashing into the pump, as well as the drain pump cover. If you notice your dishwasher is not draining or has a lot of water buildup at the bottom of the sump assembly, this filter may be damaged, clogged or broken, and in need of a replacement. To replace this pump assembly, you will only need a Philips-head screwdriver, but should start by removing your dishwasher racks. Then, pull up on the lower spray arm, and drain trap to remove them. Next, rotate the spray arm support and pull that up to remove it, at which point you can remove the base and filter for the drain pump. With those out, you can use your Philips-head screwdriver to disconnect and remove the cover and drain pump assembly. With the pump removed, you can inspect it or install the new drain pump assembly, with the same hardware as before. Then it is as simple as reassembling the rest of your dishwasher, ensuring each connection point is fastened tightly.
This is a drain pump assembly for various compatible models of dishwashers, that is responsible for draining the water from the dishwasher after every cycle. This drain pump assembly is made of plastic and fits within the sump assembly, which controls the flow of water into the drain. This drain pump assembly is a genuine OEM part and is made of a high-quality plastic but is sold as an individual component without any other parts, like its drain pump check ball which works within the pump to prevent water from backwashing into the pump, as well as the drain pump cover. If you notice your dishwasher is not draining or has a lot of water buildup at the bottom of the sump assembly, this filter may be damaged, clogged or broken, and in need of a replacement. To replace this pump assembly, you will only need a Philips-head screwdriver, but should start by removing your dishwasher racks. Then, pull up on the lower spray arm, and drain trap to remove them. Next, rotate the spray arm support and pull that up to remove it, at which point you can remove the base and filter for the drain pump. With those out, you can use your Philips-head screwdriver to disconnect and remove the cover and drain pump assembly. With the pump removed, you can inspect it or install the new drain pump assembly, with the same hardware as before. Then it is as simple as reassembling the rest of your dishwasher, ensuring each connection point is fastened tightly.
Installation Instructions
William from FRANKLIN, TN
Dishwasher stopped draining
Under sink: Disconnected drain hose to garbage disposal, shutoff water feed, unplugged power.
Under Dishwasher:
Removed water feed connection.
On top of Dishwasher:
Removed screws anchoring it to cabinet.
Pulled dishwasher out and flipped down so it’s resting on the front.
Removed drain hose on drain pump.
... Read more
/>Removed 3 torx screws on pump, greased o-ring on new pump and reinstalled doing the reverse of these instructions.
Took 1 hour and now it works great!
Under Dishwasher:
Removed water feed connection.
On top of Dishwasher:
Removed screws anchoring it to cabinet.
Pulled dishwasher out and flipped down so it’s resting on the front.
Removed drain hose on drain pump.
Took 1 hour and now it works great!
Read less
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
This pump casing assembly is compatible with various models of LG dishwashers. This assembly contains various components of the dishwasher pump. The pump is responsible for circulating water through the dishwasher during different cycles, such as washing and draining. The components included are the motor which provides the power that moves the water; the impeller, which helps to expel the water through the spray arms; the seals, which help to prevent water from leaking out, and the inlet and outlet ports which are responsible for pulling water from the tub and directing it outwards as needed; and finally, the outer housing. If any of these components fail, your dishwasher will have difficulties draining, dishes will not be cleaned thoroughly, and there will be grinding and buzzing noises during use.
This pump casing assembly is compatible with various models of LG dishwashers. This assembly contains various components of the dishwasher pump. The pump is responsible for circulating water through the dishwasher during different cycles, such as washing and draining. The components included are the motor which provides the power that moves the water; the impeller, which helps to expel the water through the spray arms; the seals, which help to prevent water from leaking out, and the inlet and outlet ports which are responsible for pulling water from the tub and directing it outwards as needed; and finally, the outer housing. If any of these components fail, your dishwasher will have difficulties draining, dishes will not be cleaned thoroughly, and there will be grinding and buzzing noises during use.
Installation Instructions
Mark from TEHACHAPI, CA
Loud noise when running - the infamous bad drive motor
Replacing this pump is pretty easy. Disconnect the power and drain hose, and pull your dishwasher out from the counter. Lay it on its side on a towel. There WILL be spillage. Disconnecting the pump is simple. There are a couple hoses, one single wire connection (the thermistor) and one multi-wire plug. The pump is held in place by a
... Read more
pair of thick rubber holders which can be pulled off by hand. That's it!
After removing the pump, I disassembled it to find out why these fail so soon. It's a very poor design. I found that the nose of the electric motor, where the bearings are located, sits in a plastic cup formed by the top of the pump body. Any leakage from the pump around the motor shaft will be held in place against the motor bearing. It has no place to go. This causes rusting of the bearing. I expect I'll be replacing this one in a few years. :(
But kudos to PartsSelect for getting the right pump assembly for me, after getting the wrong one from another supplier!
After removing the pump, I disassembled it to find out why these fail so soon. It's a very poor design. I found that the nose of the electric motor, where the bearings are located, sits in a plastic cup formed by the top of the pump body. Any leakage from the pump around the motor shaft will be held in place against the motor bearing. It has no place to go. This causes rusting of the bearing. I expect I'll be replacing this one in a few years. :(
But kudos to PartsSelect for getting the right pump assembly for me, after getting the wrong one from another supplier!
Read less
This is a chopper assembly or drain food chopper, and it is designed for your dishwasher. The chopper chops up/minces the food particles in your dishwasher to prevent them from clogging the pump. You may need to replace this part if your dishes are not being cleaned properly, your appliance is particularly noisy, or you are noticing draining problems. The tools you will need to make this repair include a number 20 and a number 15 torque screwdriver, a small flat blade screwdriver, and a pair of needle nose pliers.
This is a chopper assembly or drain food chopper, and it is designed for your dishwasher. The chopper chops up/minces the food particles in your dishwasher to prevent them from clogging the pump. You may need to replace this part if your dishes are not being cleaned properly, your appliance is particularly noisy, or you are noticing draining problems. The tools you will need to make this repair include a number 20 and a number 15 torque screwdriver, a small flat blade screwdriver, and a pair of needle nose pliers.
Installation Instructions
Bill from North Richland Hills, TX
Dishes on top rack of dishwasher were not being cleaned.
1) Remove top and bottom dish baskets from the dishwasher, this will give you room to work. To remove top basket there are clips at the end of the slide rails.
2) Remove lower spray arm by unscrewing plastic screw, it should only be hand tight.
3) In order to remove the strainer cover, you will need to remove the plastic tube th ... Read more at takes water to the middle and top spray arms. Unclip this tube from the top and middle clips and then work it out of the strainer assembly tube. Now you should be able to remove the tube at the bottom of the dishwasher by unscrewing it 1/4 turn.
4) Remove the strainer cover by unscrewing the 4 Torqs screws.
5) You will now see two smaller torqs screws that hold the hold the Chopper Assembly cover down. Take these two screws out and remove the two piece cover.
6) Pull out the broken Chopper Assembly, make sure you get all the pieces!
7) Install the new Chopper Assembly. Make sure that you install the Assembly with the small part of the screen towards the bottom of the housing. Also make sure you compress the spring as you install the part. I used a small pair of neddle nose pliers to compress the spring behind the screen in order to install the chopper assembly.
8) Put everything back together and make sure it works!
2) Remove lower spray arm by unscrewing plastic screw, it should only be hand tight.
3) In order to remove the strainer cover, you will need to remove the plastic tube th ... Read more at takes water to the middle and top spray arms. Unclip this tube from the top and middle clips and then work it out of the strainer assembly tube. Now you should be able to remove the tube at the bottom of the dishwasher by unscrewing it 1/4 turn.
4) Remove the strainer cover by unscrewing the 4 Torqs screws.
5) You will now see two smaller torqs screws that hold the hold the Chopper Assembly cover down. Take these two screws out and remove the two piece cover.
6) Pull out the broken Chopper Assembly, make sure you get all the pieces!
7) Install the new Chopper Assembly. Make sure that you install the Assembly with the small part of the screen towards the bottom of the housing. Also make sure you compress the spring as you install the part. I used a small pair of neddle nose pliers to compress the spring behind the screen in order to install the chopper assembly.
8) Put everything back together and make sure it works!
Read less
This drain pump is an authentic OEM replacement part for models of dishwasher. It is responsible for removing wastewater from the dishwasher during the drainage cycle. It is located at the bottom of the dishwasher and can be accessed by removing the lower access panel or by tipping the dishwasher on to its rear side. When activated, the drain pump pushes the wastewater through the drain hose and into the household plumbing system or garbage disposal. If the drain pump malfunctions or becomes clogged, it can lead to drainage issues, resulting in water pooling at the bottom of the dishwasher, foul odors and potentially resulting in incomplete cleaning of dishes.
This drain pump is an authentic OEM replacement part for models of dishwasher. It is responsible for removing wastewater from the dishwasher during the drainage cycle. It is located at the bottom of the dishwasher and can be accessed by removing the lower access panel or by tipping the dishwasher on to its rear side. When activated, the drain pump pushes the wastewater through the drain hose and into the household plumbing system or garbage disposal. If the drain pump malfunctions or becomes clogged, it can lead to drainage issues, resulting in water pooling at the bottom of the dishwasher, foul odors and potentially resulting in incomplete cleaning of dishes.
Installation Instructions
Douglas from SAINT JOHN, IN
Dishwasher was making a moaning sound when draining.
Unplug dishwasher. Remove lower front accessible panel. Disconnect wires to the drain pump. Rotate pump to unlock and remove. Apply plumbers grease to rubber seal and install new pump. Connect wires. Plug in dishwasher and run rinse cycle to check for no water leak. If all okay replace access panel. Done.
The pump ejects the water from the dishwasher through the drain hose.
The pump ejects the water from the dishwasher through the drain hose.
Installation Instructions
Steve from Broomfield, CO
Dishwasher not draining at end of cycle
My Bosch dishwasher is approx 11 years old. It was leaving water in the dishwasher pan at end of the cycle.
I replaced the drain pump component, which is accessible by removing the lower front panel. It is not necessary to remove the dishwasher door panel to access the pump, but may help with accessing the pump if you have di ... Read more fficulty getting it to come loose.
On the initial install of the new pump, It wasn't fully seated so it dropped a bit. Make sure the pump is fully inserted (push on it or use a bit of Vaseline on the rubber). Once fully seated it no longer dripped and the dishwasher is now draining properly.
Steps
1. Shutoff power at breaker
2. Remove lower access panel at front of dishwasher
3. Remove filter, drain and retaining clip from tub, empty water from tub with sponge or baster
4. Unplug drain plug wiring connector (small clip on right)
5. Twist old drain pump unit clockwise to remove
the old unit (have a towel ready to catch any water left in the tub)
6. Connect new pump to wiring harness
7. Insert the pump at 2 o'clock position, ensure it is fully seated (see note above).
8. Twist pump counterclockwise until it locks into place. The pump should not wiggle and be firmly connected to the unit.
9. Replace tub clip, drain screen and cover
10. Turn power back on, run cycle to test for operation and leaks
11. Reinstall lower access panel.
I replaced the drain pump component, which is accessible by removing the lower front panel. It is not necessary to remove the dishwasher door panel to access the pump, but may help with accessing the pump if you have di ... Read more fficulty getting it to come loose.
On the initial install of the new pump, It wasn't fully seated so it dropped a bit. Make sure the pump is fully inserted (push on it or use a bit of Vaseline on the rubber). Once fully seated it no longer dripped and the dishwasher is now draining properly.
Steps
1. Shutoff power at breaker
2. Remove lower access panel at front of dishwasher
3. Remove filter, drain and retaining clip from tub, empty water from tub with sponge or baster
4. Unplug drain plug wiring connector (small clip on right)
5. Twist old drain pump unit clockwise to remove
the old unit (have a towel ready to catch any water left in the tub)
6. Connect new pump to wiring harness
7. Insert the pump at 2 o'clock position, ensure it is fully seated (see note above).
8. Twist pump counterclockwise until it locks into place. The pump should not wiggle and be firmly connected to the unit.
9. Replace tub clip, drain screen and cover
10. Turn power back on, run cycle to test for operation and leaks
11. Reinstall lower access panel.
Read less
This dishwasher pump and motor assembly is compatible with dishwashers. It is supplied directly by the original manufacturer to ensure that it fits perfectly with your model. The pump and motor are responsible for moving water throughout the dishwasher during the wash cycle. The pump draws water from the tub and pumps it through various channels, such as the detergent dispenser, spray arms, and drain hose. The motor provides the power necessary to drive the circulation pump, causing the pump to rotate and circulate water. If the assembly is faulty, you will notice difficulties starting or filling the dishwasher, poor cleaning performance, incomplete cycles, and water leaks.
This dishwasher pump and motor assembly is compatible with dishwashers. It is supplied directly by the original manufacturer to ensure that it fits perfectly with your model. The pump and motor are responsible for moving water throughout the dishwasher during the wash cycle. The pump draws water from the tub and pumps it through various channels, such as the detergent dispenser, spray arms, and drain hose. The motor provides the power necessary to drive the circulation pump, causing the pump to rotate and circulate water. If the assembly is faulty, you will notice difficulties starting or filling the dishwasher, poor cleaning performance, incomplete cycles, and water leaks.