Kenmore Dishwasher Parts

Kenmore Appliance Parts
Shop By Appliance Type Shop By Part Type

Popular Kenmore Dishwasher Parts

Your Price
$6.14
  In Stock
Rack Track Stop
★★★★★
★★★★★
(41)
PartSelect Number PS11746591
Manufacturer Part Number WP8565925
The rack track stop on your dishwasher is designed to stop the dish rack at the appropriate place when opening and closing the rack. If your dishwasher is not cleaning your dishes properly, the rack stop may need to be replaced. The replacement part may differ slightly from the broken part, depending on the model. However, the different styles are interchangeable. This product is sold individually and comes in both a white and grey plastic version. Many of our customers found this repair to be very easy and takes less than 30 minutes to complete. Simply snap the old part out and snap the new part into place. You will not require any tools to complete the job. This is an authentic part approved by the manufacturer.
Fixes these symptoms
  • Door latch failure
  • Door won’t close
  • Not cleaning dishes properly
  • See more...
Installation Instructions
Steven from WASHINGTON, DC
Upper rack wheels had begun to break off. Shoddy design and materials.
I carefully followed the video instructions step by step. They were detailed, clear, and pointed out how to avoid installation mistakes. WIthout the video I would have been tempted to just figure it out myself - ("Hey, I'm a handy guy. How hard could it be, right?"). With the video I sailed right through with no dumb errors. The new rack adjuster wheel set is much sturdier than the Whirlpool original. It made sense to get new rack stops at the same time. Thank you, PartSelect. Read more...
Your Price
$14.48
  In Stock
Mounting Bracket
★★★★★
★★★★★
(12)
PartSelect Number PS11745496
Manufacturer Part Number WP8269145
The mounting bracket is sold individually, without screws. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking, or tilting forward. The bracket is made entirely of metal. It is recommended to check all brackets, if applicable, because they often wear at the same rate and both may need to be replaced. This is an OEM part that is sourced from the authentic manufacturer. Tools needed are a pair of needle nose pliers and a screwdriver.
Fixes these symptoms
Installation Instructions
Judith from Essex, MA
Lost dishwasher brackets
I called an experienced plumber, who balanced and installed my new dishwasher properly, using the brackets I ordered from Parts Select, after an INEXPERIENCED plumber had tossed the factory-provided mounting brackets out with the shipping carton. Relief! Read more...
Your Price
$8.69
  On Order
Touch-Up Paint - White
★★★★★
★★★★★
(1)
PartSelect Number PS385132
Manufacturer Part Number 72017
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is an 18 ml, or.6 fluid ounces, bottle of touch-up paint. It also features a brush for easy application. This quick-drying, long-lasting paint is perfect for fixing any nicks, scratches, or chips on the exterior of your appliance. This paint is white in color, and provides a durable finish.
Installation Instructions
Michelle from Richardson, TX
Scratches in Surface
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great. Read more...
Your Price
$34.02
  In Stock
Dishwasher Lower Dishrack Wheel Assembly - Gray
★★★★★
★★★★★
(272)
PartSelect Number PS11722152
Manufacturer Part Number W10195416V
This OEM gray Dishwasher Lower Dishrack Wheel Assembly is a plastic kit that allows the rack to slide in and out of the dishwasher easily. If it breaks or becomes damaged. sliding will feel difficult. This can happen due to normal wear and tear, and the part should be replaced if this occurs. Check your model number and user manual to make sure this part is correct. It attaches directly to the dishrack. To repair, open the dishwasher door and pull out the lower dishrack. Next, push the tab from both sides and it should pop out. To install the new wheel assembly, place it on the rack and make sure the caps overlap the wire from the inside before you clip it in place by pushing the wheel. It measures roughly 3x6 inches.
Fixes these symptoms
  • Door latch failure
  • Door won’t close
  • Leaking
  • See more...
Installation Instructions
Thomas from WEST OLIVE, MI
Broken wheel unit on the bottom dish rack
All you do is pop out the old wheel unit at two (2) points on the plastic wheel housing and pop in the new one. Easy fix. Less than a 5 minute fix. Read more...
Your Price
$33.33
  In Stock
Door Balance Link Kit
★★★★★
★★★★★
(180)
PartSelect Number PS972325
Manufacturer Part Number 8194001
This part is a door balance link kit, also sometimes known as door cable or door spring cable kit, that helps support the door as it opens and closes by connecting to the dishwasher door hinges. The kit includes two door balance links and two door balance mounts with wheels, which will replace both the left and right sides. The only tool needed is a 5/16 nut driver. Before removing the existing kit, take note of how the door balance link kit is assembled for a smooth replacement process. It is recommended to check the door springs in case they need to be replaced as well.
Fixes these symptoms
  • Door latch failure
  • Door won’t close
  • Leaking
  • See more...
Installation Instructions
Scott from Fort Lauderdale, FL
Replaced Hinge Link
Pulled dishwasher from under counter, attached link to spring, hooked spring back into frame/chassis, threaded link through pulleys, attached other end of link onto door, reinstalled dishwasher under counter. All's well. Note-I purchased an extra link anticipating that the other one will fail. They're cheap enough. Read more...
Your Price
$20.22
  In Stock
Dishwasher Bottom Door Gasket
★★★★★
★★★★★
(165)
PartSelect Number PS9495545
Manufacturer Part Number 809006501
This dishwasher door gasket (Bottom Gasket, Gasket, Door Seal, Dishwasher Door Lower Seal) helps prevent water from leaking out of the bottom edge of your dishwasher door by creating a watertight seal. This part is attached to the bottom of your dishwasher inner door panel. It is frequently exposed to water and detergent during its lifetime. The water and chemicals can eventually wear down the gasket and compromise the integrity of the seal. If the gasket is malfunctioning, the integrity of the door seal will be effected. You will notice leaking through the bottom of your dishwasher door. If your dishwasher is leaking water from the bottom of the door, first inspect the seal for food particles near the bottom and sides, and remove the buildup, as it can stop the door from closing properly and keeping a tight seal; if not, you may need to replace the bottom door gasket. Check the door gasket for tears, cuts, or wear. This part is sold individually and measures 22.5 inches by 1.25 inches. It is constructed of plastic, and comes in yellow/grey. Includes one lower door gasket.
Fixes these symptoms
  • Door latch failure
  • Door won’t close
  • Leaking
  • See more...
Installation Instructions
Scott from Flowood, MS
Bottom Door Seal fell apart and started leaking.
First I opened the door all the way. Second I reached down to the bottom gasket then grabed it on the right end of the seal that is on the right side of the door. Then I pulled the end outward from the bottom of the door toward the heater coil in the bottom of the washer. It came out real easy. You see it just snaps into a little plastic groove under the door. I then cleaned up the area for food and soap particules. I then placed the new gasket in place by lining up the notch toward the right end with the piece of plastic that encloses the right end of the plastic notch on the bottom right end of the door. Then push it in untill it stops going into the notch. It snaps in but does not make a snaping sound. It just won't go in no more. Read more...
Your Price
$6.14
  In Stock
Rail Stop Clip
★★★★★
★★★★★
(25)
PartSelect Number PS11748191
Manufacturer Part Number WPW10082861
This part goes at the end of the rail to stop the dishrack from falling out.
Installation Instructions
Greg from LEAGUE CITY, TX
Broken lower rack wheels, tine pivot, and rail stop clip
Easy, 5 minute repair. Snap off old, snap on new. I looked up on the manufacturer's website and got the replacement part numbers, then ordered on partselect for half the price. Read more...
Your Price
$6.39
  In Stock
Front Track Stop
★★★★★
★★★★★
(24)
PartSelect Number PS11755805
Manufacturer Part Number WPW10508950
This stopper is attached to the front of the top dishrack track. This stop keeps the upper rack from pulling out too far and falling from the track.
Fixes these symptoms
Installation Instructions
Sheila from FAYETTEVILLE, NY
Lost stop from one side of top rack. Rack could be pulled off track.
Looked at other side of top rack which still had the stop. Just had to orient the direction of the stop and push it firmly onto the rack arm. Took a couple tries, but it went in and locked. Works perfectly. Inexpensive and easy fix to to very annoying problem. Read more...
Your Price
$94.72
  In Stock
Dishwasher Drain Pump
★★★★★
★★★★★
(50)
PartSelect Number PS11753379
Manufacturer Part Number WPW10348269
This drain pump is used in dishwashers to remove water from the dishwasher tub. If the impeller in the dishwasher is damaged or the motor has been shorted out and will not drain, it is possible the body is cracked, causing leakage. To prevent this from happening, replace the drain pump. The tools needed for this installation are: Phillips screwdriver, 5/16 inch nut driver, 5/8 inch wrench, and a flathead screwdriver. Remember to unplug your dishwasher from the power source before beginning this installation project. Refer to the manual provided by the manufacturer for further installation instructions.
Fixes these symptoms
  • Leaking
  • Noisy
  • Not cleaning dishes properly
  • See more...
Installation Instructions
Andrew from Alexandria, VA
dishwasher not draining after wash cycle
Caviat: The actual repair is less than 15 minutes, but I spent a lot of time playing with it before I figured out it was that easy and fast. You don't need to remove the dishwasher from the counter to do this. And it will probably help to look at the new part closely so you can understand where the retainer clip is to press it and release the old pump.

First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done.
Read more...
Your Price
$40.18
  In Stock
Upper Rack Adjuster Kit - White Wheels, Left and Right Sides
★★★★★
★★★★★
(290)
PartSelect Number PS10065979
Manufacturer Part Number W10712395
This authentic Dishwasher Upper Rack Adjuster Kit with white wheels is a kit made up of primarily plastic and metal components, and which will require a screwdriver to install. This kit comes with all the necessary parts for a dishwasher rack adjuster. It fits onto dishwasher rack and connects it to the track allowing it to slide in and out. If broken then the rack will no longer slide properly, and the part must be replaced. In many cases, our customers have reported the top rack of their dishwasher hanging down or sagging due to the adjuster kit, particularly the wheels, have broken or failed. If you are having problems in this area, this kit will help get your dishwasher back up and running. Check your model number and user manual to see if this part is right for you. The parts for this kit come as a package and are not generally sold individually. Please see as follows for detailed repair instructions: First you will have to remove your upper dish rack and the old adjust kit. Now, when installing the new kit, count 4 rungs from the back of the basket toward the front. Take your new metal adjuster and thread the shaft through the fourth rung. You may have to tilt it to get it through. When you straighten the part the portion of the wheel should be on the outside of the rack and the shaft will be on the inside of the rack. Take your positioner clips and use them to secure the adjuster to the rack. You will see two front tabs and two back tabs. The back tabs will also need to be tilted into place so that they are on the inside of the rack. The flat part of the positioner clips should be on the outside of the rack. Then you will push the clips down on to the adjuster to clip them into place. Now you will have to install the adjuster body on to the adjuster. Pull your adjuster all the way down. Tilt the adjusted toward the inside of the rack, you will notice that the adjuster body has a channel that will fit the adjuster. Slide those two pieces into place together. You will have 4 notches on your adjuster body that fit perfectly with your rack. Pull-on your metal adjuster to lock it into place. Grab your actuator. You want to make sure that the thumb pad of your actuator is facing toward the inside of the rack and is closer to the front of the rack. Pull the adjuster arm up as far as you can, so that the body is a little bit above the top of the rack. The set the actuator inside of the two slots at the top of the body. You may have to tilt the body toward the inside of the rack to fit the actuator into place. Once you have that part in place, push the whole assembly down and press it back up against the side of the rack into place again. Now you will take the adjuster cover and install it on to the body from the outside of the rack. There is a little tab at the top of the cover, you will have to push that into place in the slot at the top of the adjuster body. That just snaps down into place. Then you install your two T15 Torx screws into the cover to hold it into place. This installation is the same for both sides.
Fixes these symptoms
  • Door latch failure
  • Door won’t close
  • Not cleaning dishes properly
  • See more...
Installation Instructions
Richard from OAKLAND, CA
Instruction from Whirlpool Not Good (No problem with Part Select)
Trial and error. The instructions from Whirlpool included with the part had minuscule pictures so it was hard to follow. The written instructions were good. But "a picture is worth a thousand words." Eventually it worked. The metal replacement part is much better the the plastic original. Not a good reflection on Whirlpool. Read more...

Appliance Type

Related Parts

Popular Kenmore Dishwasher Models

Below are the most popular Kenmore Dishwasher models we have. Enter your model number in the search box to find your model.