My Orders
Kenmore Dishwasher Valves
GET YOUR OFFICIAL Kenmore PARTS TO ENSURE VICTORY
Popular Kenmore Dishwasher Valves
This water inlet valve is usually located behind the lower kickplate panel in either the right or left corner of the dishwasher. The attaching solenoids on the valve open and close according to the desired amount of water needed. The water inlet valve on your dishwasher supplies water to the dishwasher. If your dishwasher is leaking because it has overflowed, the water inlet valve may be the cause. If your dishwasher continues to fill above the heating element, try opening the door latch to see if it stops filling. If it continues to fill, you have a defective inlet valve that will need to be replaced.
This water inlet valve is usually located behind the lower kickplate panel in either the right or left corner of the dishwasher. The attaching solenoids on the valve open and close according to the desired amount of water needed. The water inlet valve on your dishwasher supplies water to the dishwasher. If your dishwasher is leaking because it has overflowed, the water inlet valve may be the cause. If your dishwasher continues to fill above the heating element, try opening the door latch to see if it stops filling. If it continues to fill, you have a defective inlet valve that will need to be replaced.
Installation Instructions
CHRIS from ROANOKE, VA
Water leaking from Inlet Valve
Remove the bottom cover plate. Disconnect the water inlet and black rubber hose. Remove 2 mounting screws. Pull out electrical connector. Reverse order. Be sure to get the brass inlet connector really tight so it won't leak. I did the final tightning after the part is mounted. Not a bad repair at all. The only problem was that it
... Read more
leaked in the first place and messed up my subfloor and laminate flooring.
Read less
This water inlet valve should be located behind the lower kick plate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.
This water inlet valve should be located behind the lower kick plate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.
Installation Instructions
Melissa from AIKEN, SC
Inlet valve wasn't working
Put thread tape on threads. Screwed water hose to part. Pushed hose onto part. Pushed electric clip to part. Screwed part onto washer. Done
The water inlet valve assembly is a crucial component of dishwashers that controls the flow of water into the unit. This genuine OEM replacement part includes the inlet valve, inlet hose, and hose clamp to ensure the proper water supply for your dishwasher’s operation. Designed for specific models, this part ensures that water is fed into the dishwasher during the wash cycle, promoting efficient cleaning. Before installation, it is important to unplug the dishwasher and turn off the water supply to avoid any accidents. Wear work gloves for your safety during the installation process. Be sure to verify the compatibility with your dishwasher’s model number, as similar-looking parts may have slight variations in size or design.
The water inlet valve assembly is a crucial component of dishwashers that controls the flow of water into the unit. This genuine OEM replacement part includes the inlet valve, inlet hose, and hose clamp to ensure the proper water supply for your dishwasher’s operation. Designed for specific models, this part ensures that water is fed into the dishwasher during the wash cycle, promoting efficient cleaning. Before installation, it is important to unplug the dishwasher and turn off the water supply to avoid any accidents. Wear work gloves for your safety during the installation process. Be sure to verify the compatibility with your dishwasher’s model number, as similar-looking parts may have slight variations in size or design.
Installation Instructions
Joseph from BIRMINGHAM, MI
Inlet valve leaking at water connection
The valve has a plastic fitting to attach the the water line with a hose fitting. Was not carful enough with the original and damaged it attaching the water line. Ordered a replacement fitting. While it is possible to replace the water inlet valve without pulling the dishwasher out from the cabinet found it was easier to get at with the m
... Read more
achine out. The video does and good job of showing the removal and replacing the valve. Easy job, don't be like me and be careful attaching the water line.
Read less
This dishwasher water inlet valve regulates the flow of water into the appliance during each cycle, helping ensure proper filling and efficient operation. If your dishwasher is leaking, overfilling, or not filling at all, this component may need to be replaced. Designed for compatibility with a wide range of models, it offers reliable performance and a secure fit. To ensure the correct part, always verify your dishwasher’s model number before ordering, as similar-looking parts may vary in size or shape. Before installation, disconnect the appliance from its power source and wear protective gloves for safety.
This dishwasher water inlet valve regulates the flow of water into the appliance during each cycle, helping ensure proper filling and efficient operation. If your dishwasher is leaking, overfilling, or not filling at all, this component may need to be replaced. Designed for compatibility with a wide range of models, it offers reliable performance and a secure fit. To ensure the correct part, always verify your dishwasher’s model number before ordering, as similar-looking parts may vary in size or shape. Before installation, disconnect the appliance from its power source and wear protective gloves for safety.
Installation Instructions
Robert from E GRAND FORKS, MN
High pitched noise when the washer filled at the beginning of the cycle.
Watched the video, it went as advertised. Easy repair and the noise is gone.
The dishwasher water inlet valve controls the water flow into your appliance, ensuring proper fill levels for effective cleaning. This genuine OEM replacement part is compatible with select Bosch, Thermador, and Gaggenau models and meets strict quality standards. If the valve is defective, the dishwasher may fail to fill or underfill. To install, unplug the dishwasher, shut off the water supply, and wear gloves for safety. Verify compatibility before ordering.
The dishwasher water inlet valve controls the water flow into your appliance, ensuring proper fill levels for effective cleaning. This genuine OEM replacement part is compatible with select Bosch, Thermador, and Gaggenau models and meets strict quality standards. If the valve is defective, the dishwasher may fail to fill or underfill. To install, unplug the dishwasher, shut off the water supply, and wear gloves for safety. Verify compatibility before ordering.
Installation Instructions
Bill from NORTH HALEDON, NJ
The valve allowed water to fill the dishwasher when not in use.
This was the third time I replaced a fill valve in a Bosch diswasher, twice in this unit and once in a previous unit. I read the installation hints on your web site and want to add the following suggestion.
The notes on your web site say you can remove the valve from behind the toe face and pull it out to reach the hose and plu ... Read more g. I found that the Bosch designers called for both the hose and wire to on the short side. I found that pulling the dishwasher forward 6" to 9" allows you to access these connections from the side at least to hold them while making the connection. I hope this helps. Thank you, Bill
The notes on your web site say you can remove the valve from behind the toe face and pull it out to reach the hose and plu ... Read more g. I found that the Bosch designers called for both the hose and wire to on the short side. I found that pulling the dishwasher forward 6" to 9" allows you to access these connections from the side at least to hold them while making the connection. I hope this helps. Thank you, Bill
Read less
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
This dishwasher water inlet valve is a single-coil solenoid component responsible for regulating the flow of water into the appliance. It ensures the correct amount of water is delivered during each cycle, supporting optimal cleaning performance and preventing issues such as underfilling, overfilling, or leaks. By electronically opening and closing based on the cycle’s requirements, the valve helps maintain proper water pressure and temperature balance. Replacing a faulty valve can resolve symptoms like the dishwasher not filling, leaking, or failing to clean effectively. This component is engineered for durability and consistent operation.
This dishwasher water inlet valve is a single-coil solenoid component responsible for regulating the flow of water into the appliance. It ensures the correct amount of water is delivered during each cycle, supporting optimal cleaning performance and preventing issues such as underfilling, overfilling, or leaks. By electronically opening and closing based on the cycle’s requirements, the valve helps maintain proper water pressure and temperature balance. Replacing a faulty valve can resolve symptoms like the dishwasher not filling, leaking, or failing to clean effectively. This component is engineered for durability and consistent operation.
Installation Instructions
MICHELLE from EDEN VALLEY, MN
water leaking out of bottom of machine
removes the 1 screw that held the old one in and removed the water lines the supply line with a adjustable wrench and the internal line had a hose clamp on it then i just went in reverse...
This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.
This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.
Installation Instructions
Bruce from GRANDVIEW, MO
washer filled in when off..
replaced the valve
This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed. NOTE: As per the manufacture this part has been updated from the original part. It may be a different color, and you may need to order an elbow (# W10685193) for the new designed valve to work.
This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed. NOTE: As per the manufacture this part has been updated from the original part. It may be a different color, and you may need to order an elbow (# W10685193) for the new designed valve to work.
Installation Instructions
David from Lexington, NC
Inlet valve was leaking from crack in brass fitting
Removed the lower panels from beneath the dishwasher door. 4 screws. Turned off the water.
Removed one screw holding the inlet valve to the side rail of the dishwasher. It was attached to the hot water line and then the washer water input line. Removed the electrical connector..Pull straight off, and use a pair of pliers to ... Read more open the squeeze clamp on the washer hose. The hot water supply hose has a brass fitting to loosen and remove.
Replaced the inlet valve, reconnected the electrical and also replaced the hot water line from under the sink to the washer. Used a new braided 5' hose with fittings. Used teflon tape on the screws and did not over tighten the brass fittings.
Turned on the hot water supply and checked for leaks. Operated the washer and checked for leaks. Replaced the lower covers.
Removed one screw holding the inlet valve to the side rail of the dishwasher. It was attached to the hot water line and then the washer water input line. Removed the electrical connector..Pull straight off, and use a pair of pliers to ... Read more open the squeeze clamp on the washer hose. The hot water supply hose has a brass fitting to loosen and remove.
Replaced the inlet valve, reconnected the electrical and also replaced the hot water line from under the sink to the washer. Used a new braided 5' hose with fittings. Used teflon tape on the screws and did not over tighten the brass fittings.
Turned on the hot water supply and checked for leaks. Operated the washer and checked for leaks. Replaced the lower covers.
Read less
This water inlet valve is for dishwashers.
Water inlet valve supplies water to the dishwasher.
Unplug the dishwasher and shut off the water supply before installing this part
This water inlet valve is for dishwashers.
Water inlet valve supplies water to the dishwasher.
Unplug the dishwasher and shut off the water supply before installing this part
Installation Instructions
CHERI from CREEKSIDE, PA
Dishwasher was not filling up at the start of the cycle.
This was really easy. Have done it before on other older dishwashers in the past.
Turned off the breaker for the dishwasher. Turned off the water supply valve. Unscrewed the screws in the panel that hides the parts under the dishwasher. Unscrewed the screws anchoring the dishwasher to the counter. Slid the dishwasher out about a foo ... Read more t. Inlet valve was located on the front left side of the dishwasher. Unclipped the wire harness. Placed a cookie sheet under the water line. Unscrewed the water line from the inlet valve. Unscrewed the two Phillips head screws holding the valve to the dishwasher frame. Got the new part. Put the screws back into the frame. Reconnected the water line and wire harness. Slid the washer back into place. Turned on the water valve. Watched for leaks. Turned the breaker back on and started the cycle. Watched for leaks. Once I saw there weren’t any replaced the screws anchoring it to the counter and replaced the cover on the bottom. That was it! Took me longer to type out the steps than it did to actually do the repair.
Turned off the breaker for the dishwasher. Turned off the water supply valve. Unscrewed the screws in the panel that hides the parts under the dishwasher. Unscrewed the screws anchoring the dishwasher to the counter. Slid the dishwasher out about a foo ... Read more t. Inlet valve was located on the front left side of the dishwasher. Unclipped the wire harness. Placed a cookie sheet under the water line. Unscrewed the water line from the inlet valve. Unscrewed the two Phillips head screws holding the valve to the dishwasher frame. Got the new part. Put the screws back into the frame. Reconnected the water line and wire harness. Slid the washer back into place. Turned on the water valve. Watched for leaks. Turned the breaker back on and started the cycle. Watched for leaks. Once I saw there weren’t any replaced the screws anchoring it to the counter and replaced the cover on the bottom. That was it! Took me longer to type out the steps than it did to actually do the repair.
Read less