Whirlpool Washer Pumps

Whirlpool Appliance Parts
Shop By Part Type

Popular Whirlpool Washer Pumps

Your Price
$38.59
  On Order
Direct Drive Water Pump
★★★★★
★★★★★
(79)
PartSelect Number PS11741239
Manufacturer Part Number WP3363394
The direct drive drain pump (Whirlpool Direct Drive Washer Pump, Drain Pump, Washer Drain Pump, Water Pump) removes water from the washer during the drain cycle without the use of a belt. The pump is supposed to drain the water from the washer; if the water isn’t draining or if there is a leak, you may have a problem with your pump. You must replace this part if there is a blockage or clog. Although the symptoms may point to a malfunctioning drain pump, there could actually be a problem with one of the connecting hoses. This pump connected directly to the motor, and comes in white plastic. This replacement part features 1 direct drive water pump with 2 ports for water to pass through: a large one and a smaller one.
Fixes these symptoms
  • Fills and drains at the same time
  • Leaking
  • Leaks water
  • See more...
Installation Instructions
RICHARD from PHILA, PA
Replace Water Pump Coupling
Removed casing tip over washer disconnected water pump. Disconnected motor then replace coupling then reassemble motor then replaced water pump. Read more...
Your Price
$128.50
  In Stock
Washer Drain Pump
★★★★★
★★★★★
(80)
PartSelect Number PS11757304
Manufacturer Part Number WPW10730972
This is a manufacturer-approved replacement drain pump for your washing machine. To complete this repair you will need a 1/4 inch nut driver, 5/16ths nut driver, a flat blade screwdriver, and a pair of pliers. Make sure to disconnect power to the washer before beginning this repair.
Fixes these symptoms
  • Burning smell
  • Engine runs but does not pump water
  • Leaking
  • See more...
Installation Instructions
Andrew from St.Louis, MO
F 21 error
Removed the front panel unplugged
The washer drained water out, lift the washer up to un screw the drain pump. Then unhooked the hoses from pump put the other pump in.
Read more...
Your Price
$55.27
  On Order
Drain Pump
★★★★★
★★★★★
(18)
PartSelect Number PS11756700
Manufacturer Part Number WPW10605427
Fixes these symptoms
Installation Instructions
JASON from HILLIARD, FL
Drain pump was cracked
Turned washer on its side. Pulled the bottom plate off. Then unplugged the electrical lines. Then unbolted the drain pump and bolted the new drain pump in. Then reversed the process. Read more...
Your Price
$175.99
  On Order
Drain Pump Kit
★★★★★
★★★★★
(42)
PartSelect Number PS1485610
Manufacturer Part Number 280187
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. This part is used on front load models.
Fixes these symptoms
Installation Instructions
Donald from Wichita, KS
Washer would not drain ,F02 and SUD code displaying
(1) First I unpluged the washer then I removed the water from the tube with a water vac.(2) Then I removed the three (3) screws that holds the front panel, using a Torx T-20 socket. ( this is a front load washer ). The panel is below the loading door.
(3) I packed towels under the washer.
(4) I slowly removed the cleanout in the front of the pump, using the water vac to catch the water as it leaked out.
(5) I removed the wiring to the motor.
(6) I removed the screw that holds the pump in place with a Torx T-20 socket.
(7) I pulled the pump forward so the clamps that hold the drain hose and discharge hose could be removed using the hose clamp pliers. ( they come off much easier then they go back on ).
(8) I tested the pump and found it would run but was making a lot of noise and running slow.
(9) To reinstall start with number (7) and work backwards to number (1) skipping (3) and (4).
Don Kramer
Wichita, Kansas
Read more...
Your Price
$129.60
  In Stock
Drain Pump
★★★★★
★★★★★
(18)
PartSelect Number PS5136124
Manufacturer Part Number W10536347
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.
Fixes these symptoms
Installation Instructions
ROBERT from BARRINGTON, IL
Loose change entered drain pump, cracked housing leaked all water out
Disconnect power, hot/cold supply and drain hose. Tip washer onto front side, expect some additional water to leak out. Remove the cracked drain pump, 3 screws, hose clamps, and electrical plug.

Tip washer back up, use the putty knife to pop the top cover up (clips are about 6.5in in from sides). Unclip the white plastic cover over the outer and inner tubs. Pop the center cap from inside the inner tub, exposing the bolt holding the inner tub down. Remove bolt, pull inner tub up and out.

At bottom of outer tub remove 2 screws from drain access cover, should find some change under there (or in the pump).

Re-assemble using new pump.

Note:
Before new pump arrived I was able to use some silicone sealant, epoxy, and black tape to temporarily fix the cracked pump housing after pulling it out.
Read more...
Your Price
$127.92
  In Stock
Drain Pump - 120V 60Hz
★★★★★
★★★★★
(9)
PartSelect Number PS11751719
Manufacturer Part Number WPW10276397
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time
Fixes these symptoms
Installation Instructions
REED from BUCHANAN, NY
Wouldn’t drain pump made loud noise
Removed old drain pump and found a sock in the inlet - must have burned out pump because after removing it pump was still defective. Installed new pump in about 30 minutes and off to the races no more issues Read more...
Your Price
$60.57
  On Order
PUMP-WATER
★★★★★
★★★★★
(8)
PartSelect Number PS11757016
Manufacturer Part Number WPW10661045
Fixes these symptoms
Your Price
$76.81
  In Stock
Water Drain Pump
★★★★★
★★★★★
(4)
PartSelect Number PS11756530
Manufacturer Part Number WPW10581874
Genuine OEM WPW10581874 Washer Drain Pump. The drain pump removes water from the washer during the drain portion of the cycle.
Fixes these symptoms
Installation Instructions
Jim from DOVER, TN
Washing machine would not drain and a drn code would show in the display. Once the machine filled all the way up with water. Sometimes it would not refill to rinse.
I removed the 2 hose clamps connecting to the pump, removed 3 screws holding pump in place, and disconnected 2 wires plugged into pump. Put the new pump on in reverse order. Read more...
Your Price
$75.40
  In Stock
Direct Drive Water Pump
★★★★★
★★★★★
(7)
PartSelect Number PS11741242
Manufacturer Part Number WP3363892
This white direct drive drain pump is intended for use with washing machines that do not have belts. This pump has a backflow flapper valve, and two large ports for water to pass through.
Fixes these symptoms
Installation Instructions
Gary from Huntington, WV
Pump was leaking a little at the seam joint
Tilted washer onto its back and removed the "cardboard" bottom sound absorption cover (2 sheet metal screws). This provides access to the pump that is located on top of the motor. Slid off each of the 2 clamps that secure the two drain hoses using slip joint pliers. Then popped loose the 2 metal holddown bracket clamps that secure the pump housing to the motor.
The next step gave me a real fit... the pump housing is supposed to just lift off the motor shaft with little effort but mine was a bear. No matter how much I pulled and tugged, it didn't want to budge. Because the motor assembly is mounted on a semi-moveable suspension, when I grabbed the pump and pulled, the whole motor assembly tended to move too. I eventually had to resort to using 2 large flat blade screwdrivers to pry the pump off ... CAUTION!!! Be careful not to put too much force because you can dent the motor shaft grease housing (which I did). Fortunately, I didn't dent it enough to poke a hole in it but it was deformed...
And the reason it didn't want to come off easily was - the shaft had been getting wet which caused some rusting/pitting of the shaft. Although the pump housing is all plastic, the shaft was rusted tight on it. It did come off after much tugging and prying. Otherwise this would be a very easy repair.
Put the new pump in place but it wouldn't go on the shaft until I took some sandpaper and removed as much of the rust as I could. I put a little grease (vaseline) on the motor shaft and pump housing connection to make it easier to slip on. Aligned the motor shaft and pump housing - it is keyed (meaning it only goes on one way due to the shape of the motor shaft). Once keyed on properly, it slid down easily. Reattached the 2 metal holdown brackets and reattached the 2 drain hoses. Replaced the bottom cover.
I did not encounter very much water in the hoses but be advised there can be enough water to get things wet (motor, floor) so you may want to have a small container to get as much water out of the hoses. Also having towels to catch any water remaining in the pump housing so it doesn't end up spilling onto the motor (a bad thing). Of course one has to UNPLUG the electrical cord BEFORE beginning this repair! Also you will most certainly need to shut off the incoming water lines and disconnect the hoses to allow you to move the washer to a position that makes it easy to get to bottom.
That's all I can think of... a simple repair that should go quick if the motor shaft isn't rusted on!
Good Luck...

P.S. I figured the drain pump was leaking AFTER I removed the bottom cover and looked for water evidence here and there. Suspected the pump but couldn't be sure until I set the washer back up normally and ran a cycle. Using a mirror I checked to see where the drips were coming from.
Read more...
Your Price
$126.13
  In Stock
Drain Pump
★★★★★
★★★★★
(4)
PartSelect Number PS11754363
Manufacturer Part Number WPW10409079
Fixes these symptoms
Installation Instructions
Raymond from SEBASTIAN, FL
water would not discharge from tub.
replaced the drain pump which took about 10 minutes. removed 3 screws, unplug elec. wire, remove 2 water hoses, put back together in reverse. Read more...

Related Parts