Whirlpool Washer Belts

Videos!

Your Price

$19.71

Whirlpool Washer Drive Belt

★★★★★

20 Reviews

PartSelect Number PS11747978

Manufacturer Part Number WPW10006384

The main drive belt is designed to ride on the pulley until the basket gets up to speed.

Fixes these symptoms

Burning smell
Spinning Issues
Spins slowly
See more...

Installation Instructions

Jerry from WALLA WALLA, WA

Noise on bottom of Washer louder as time went on. 1 1/2 years

Well, first investigated and found loose nut on drive clutch. First take off the two screws with nut drive then cover off using a screwdriver blade to snap off the cover. Then socket ratchet to take off the nut on drive clutch. take off belt by slowly rotating the drive gear. two screws that hold the electronics to the upper drive clutch and put aside, so you can snap off the cover for drive clutch on upper part with screwdriver and off the parts come and install whole unit back as took it apart. Line up the new upper clutch so that is position as was before. (Using parts diagram helps a lot as www. partsselect.com has for you or Maytag.com.) Then put the electronic part board back on and the gear and nut. Make sure it is tight by several attempts to make sure it's snugged up good and then slowly roll belt back on the pulley and motor drive. Put your cover guard back on with two screws and done. Read more...

Videos!

Your Price

$52.85

Whirlpool Washer Drive Belt

★★★★★

12 Reviews

PartSelect Number PS11754067

Manufacturer Part Number WPW10388414

This drive belt is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt get wear and tear. NOTE: Per Manufacture, belt measures 48.22" long uninstalled and the belt will stretch To 51.53" when installed.

Fixes these symptoms

Burning smell
Spins slowly
Will not agitate
See more...

Installation Instructions

Francis from Rochester, NY

Washer made loud banging noise during spin cycle

I first removed the back panel held on by about 10 screws. I removed the drive belt from the pulley, then removed the lock nut securing the pulley to the drum & removed the pulley. Attached the new pulley to the drum, tightened on the lock nut, attached the new belt & ran a spin cycle. When that went OK I replaced the back panel & the washer was back in service. Read more...

Videos!

Your Price

$50.31

Whirlpool Washer Drive Belt

★★★★★

13 Reviews

PartSelect Number PS11746258

Manufacturer Part Number WP8540101

This part is the replacement drive belt for your washer. It is made of black rubber and is approximately ½ an inch wide and 48 inches long. It has 6 grooves and is sold individually. The drive belt is found between the motor pulley and the drive pulley, and it connects the motor to the drive system. When the belt is running, it allows the basket or tub to spin. If the belt is stretched, worn, or broken, the tub will not turn. A warped belt can also cause the washer to be noisy while operating. This part is an authentic OEM part sourced directly from the manufacturer.

Fixes these symptoms

Burning smell
Spins slowly
Will not agitate
See more...

Installation Instructions

Keith from Austin, TX

Bad drum belt

Our whirlpool washer drum wasn't turning and there was a thunking noise from the machine when the drum should have been rotating.

I opened the top and back of the washer using a ratchet wrench. There were 4 screws holding on the top (at the top rear of the machine) and about 12 or more holding on the back panel. Removing these I could see the belt had become frayed, had come off of the drum, and was bunched around the motor drive wheel. The old belt was still usable, but clearly not going to last much longer so I purchased a new belt. The new belt was tighter than the old belt (which is good) and so took a fair amount of effort to get back onto the drum. I had to hold in place while turning the drum, something hard to do because of the braces on the back of the washer get in your way. But, I eventually got the belt propery seated. I then replaced the back and top panels. All appears to be working as it should. Read more...

Your Price

$45.97

Whirlpool Washer Belt

★★★★★

1 Review

PartSelect Number PS11751386

Manufacturer Part Number WPW10260319

Your Price

$45.18

Whirlpool Washer Belt

PartSelect Number PS11749958

Manufacturer Part Number WPW10192984

Fixes these symptoms

Spins slowly
See more...

Installation Instructions

Diane from Kenna, WV

Clothes not spinning on high speed

Removed braces, then removed belt. Started the belt on, then when I got to a point that I couldn't turn it any more I put the cable tie over belt and wheel,tighten them as tight as I could. When the belt got about on I watched close if you don't it will come off going around motor. Read more...

Your Price

$60.51

Whirlpool Washer Drive Belt

★★★★★

5 Reviews

PartSelect Number PS11754068

Manufacturer Part Number WPW10388418

The main drive belt is designed to ride on the pulley until the basket gets up to speed.

Fixes these symptoms

Will not agitate
See more...

Installation Instructions

Robert from OAKDALE, CT

Replace worn washer belt

Remove old belt, rotate large washer belt wheel, guiding belt off large wheel.
Guide new belt onto Washer Large Wheel. Use a pair of pliers to hold belt onto wheel as one turns the large washer belt wheel, guiding belt onto wheel. Note belt will be tight. Seems like belt will not fix but keep going it will fit, you might even hear it pop on.
Old Part number (W10116215) new replacement Part number (W10388418).
New replacement washer belt fits tight, that is ok. Read more...