Maytag/Maytag_Thumb/DBALC0A5.gif
See part 1 in the diagram
Replacing your Whirlpool Washer Drain Pump play video
( Grid squares measure 1x1 inch )

Get in touch, we're here to help!

Open until 12am EST

customerservice@partselect.com

Drain Pump

★★★★★
★★★★★
22 Reviews
$117.19   In Stock

Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS5136124
Manufacturer Part Number W10536347
Manufactured by Whirlpool
Product Description

Drain Pump Specifications

This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.
How Buying OEM Parts Can Save You Time and Money play video

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part fixes the following symptoms:
Leaking | Will not drain | Noisy | Pumps but will not spin
This part works with the following products:
Washer.
This part works with the following products:
Whirlpool, Kenmore, Maytag.
Part# W10536347 replaces these:
AP5650269, 2392433, W10536347, 8542672, W10049390, W10155921, W10217134, W10281682
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

12 questions answered by our experts.
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Ryan
August 21, 2017
I am looking for a part : Drain pump. But as i am searching i see there is a "drain pump" and a "water pump circulator". I am searching for a friend so i am unsure which part that i actually need. Question: Are these the same parts? Or is one different from the other. They both look similar in the photos.
For model number WTW6800WW1
Dear Ryan, Thank you for your inquiry. Yes there are 2 pumps for your washer. To verify which one is causing the issue you will need to use a multimeter to check the continuity of each pump. I hope this helps. Thank you and have a great day!

12 people found this helpful.

Was this helpful?
Thank you for voting!
A.O.
January 19, 2018
My Whirlpool washer yesterday washed a heavy load and did not completely unload and gave an Ld code. After stopping and starting about 3 times I got it to finish. There was dirt in the bottom of washer. I ran the wash again and was able to finish the wash. I then ran a lite color load and no problem. I went to run a heavy load this morning of jeans and shirts and the same thing happened as it did yesterday. Took load out of wash and got as much water out as could and turned on its side . Took unload pump off with no obstructions noted. I then took the hose off to check the impeller and nothing was noted. I was able to turn the impeller but had a little resistance at one point each time it turned. It would go past and about another half turn the same resistance. It did not matter which way it was turned, like a gasoline engine with a spark plug in. Can you help?
For model number WTW6800WW1
Hello A.O., Thanks for your question. This error code will appear if unit takes longer than 5 minutes to pump out water to the point where the pressure switch resets. Press 'Stop/Cancel' to clear display. You may want to test your drain pump with a multimeter as well to see if it has electrical continuity, but since there is little resistance that would already be a sign that the impeller is failing, and as such should be a cause to replace the pump. I hope this helps.

8 people found this helpful.

Was this helpful?
Thank you for voting!
Darryn
February 12, 2018
Pump makes a rattling noise like there is a coin stuck in it, is that a possibility or is an impeller broken
For model number MVWB800VQ0
Hi Darryn, Thank you for the question. It is actually common for coins or small objects to become lodged in the pump. Most times you can remove the pump and remove the object, hopefully before it has caused damage to the impeller. Hope this helps!

5 people found this helpful.

Was this helpful?
Thank you for voting!
Robert
August 27, 2017
Is there a replacement part for just the pump hose housing? Pump works fine the hose clamp housing has been cracked by coins.
For model number wtw6340wwo
Hi Robert, Thank you for the question. Very sorry but I am showing the manufacture only sells the housing as part of the pump assembly, so you will need to order a full new pump. Hope this helps!

5 people found this helpful.

Was this helpful?
Thank you for voting!
Justin
September 25, 2017
Drain pump motor runs but it does not pump water out. Could the impeller be loosed? No blockage seen. Sd code given.
For model number WTW6600SW2
Hi Justin, Thank you for the question. The Sd error code indicates the Suds Lock (overdose of detergent detected during the wash cycle). If the problem continues after the correct amount and correct type of detergent is being used, I suggest running a "Clean Washer" cycle to remove detergent that might have built up in the washer. Hope this helps!

4 people found this helpful.

Was this helpful?
Thank you for voting!
Wayne
December 6, 2018
Is there a way to test my drain pump?
Hi Wayne, Thank you for your question. You can test the drain pump for continuity with a multimeter. I hope this helps. Thank you and have a great day!

2 people found this helpful.

Was this helpful?
Thank you for voting!
Jeff
April 24, 2019
Machine did fill did not agitate 35 min later the water was still in the drum, when unplugged then plugged in there was a mummming noise nothing happen can you tell me if its the pump or the board Jeff
For model number MVWB750WQ1
Hello Jeff, thank you for inquiring. For the combination of the symptoms mentioned, you will want to replace either the Basket Hub Kit part PS11723155, the Sensor part PS11749664, or the Drain Pump part PS5136124. We hope this helps.

2 people found this helpful.

Was this helpful?
Thank you for voting!
Susan
June 24, 2019
I purchased an oem part w10536347 thru another site, and it didn't come with the shield. Almost all of the sellers of this part don't offer it with a shield. How important is the shield? I am not able to buy it separately. My understanding is it is a waterproof shield to keep any water from falling on the pump. But why would any water drip on the pump?
For model number MVWB750WQ1
Hello Susan, Thank you for the question. Others have installed and are using the pump without the shield without issue. Hope this helps!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Lou
August 18, 2021
The machine is making roaring noise when in the spin cycle. I replaced the suspension springs and the basket hub assembly. Still makes the same sound. The tub does not shake. I see where a noisy unit can be caused by the pump. Do you believe that will solve the noisy problem? I bought the sensor but have not installed it yet. Considering ordering the pump and replacing them at the same time.
For model number WTW6200VW0
Hello Lou, Thank you for writing. The most likely issue would be the Tub Seal and Bearing Kit PartSelect Number PS3503261.This kit includes the shaft, 3 bearings, seals, grease, adhesive, and the spanner nut, which is NOT sold separately. Also, may require a bearing driver tool to install. PS3503307 After that the Pump PartSelect Number PS5136124 would we the next part to try. We hope this helps.

1 person found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
Loretta
November 23, 2017
My washer will pump all the water out but 2 gallons of water. I have taken it all apart and nothing it blocking anything. If i suck out the last 2 gallons of water it will then start to spin. It will through a suds code or a blockage code. What would you suggest is my problem
For model number MVWB800VQ0
Hi Loretta, Thank you for the question. Normally this happens when the using the wrong type of soap or to much soap. I suggest running a load with no dishes with a cup of vinegar to see if it clears the code and drainage system. Hope this helps!

Was this helpful?
Thank you for voting!
Part Videos

Replacing your Whirlpool Washer Drain Pump

Replacing your Whirlpool Washer Drain Pump play video
Customer Repair Stories
 Average Repair Rating: 3.5 / 5.0, 16 reviews. What's this?
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
Loose change entered drain pump, cracked housing leaked all water out
Disconnect power, hot/cold supply and drain hose. Tip washer onto front side, expect some additional water to leak out. Remove the cracked drain pump, 3 screws, hose clamps, and electrical plug.

Tip washer back up, use the putty knife to pop the top cover up (clips are about 6.5in in from sides). Unclip the white plastic cover over the outer and inner tubs. Pop the center cap from inside the inner tub, exposing the bolt holding the inner tub down. Remove bolt, pull inner tub up and out.

At bottom of outer tub remove 2 screws from drain access cover, should find some change under there (or in the pump).

Re-assemble using new pump.

Note:
Before new pump arrived I was able to use some silicone sealant, epoxy, and black tape to temporarily fix the cracked pump housing after pulling it out.
  • ROBERT from BARRINGTON, IL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Socket set
  • Parts Used:
    W10536347
197 of 225 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water pump for draining
The actual install of the pump was extremely easy. I removed the back cover, (After unhooking water, drain and electricity. I laid the machine on its front ( USE CAUTION WHEN DOING THIS, THERE ARE SHARP EDGES on the FRAME) After bandaging my cut fingers, I used a nut-driver/screwdriver to remove the screws, pliers to remove the Spring clamps, unhooked the wiring( its a single plug in) and reverse the procedure for installing.

I saw where a person had put the screws in the filter below the tub. I had to find the clips on the front of the machine, (about 7 in in from the sides) I removed the nut cover on the agitator, used a socket to remove the agitator, tub, and a nut driver to remove the filter. I found 3 areas where coins could get through the drain filter, and I used self tapping screws to make an obstruction that water could get through but not the coins. I reinstalled tub. Before re installing the agitator, I got some fiber glass window screening and cut a piece to go over the drain slots in the bottom of the tub but under the agitator, then reinstalled the agitator.

I noticed that the new pump had more re enforcing at the areas where the 1st pump broke. I doubt that it will break, but I am not taking any chances. I put the screen in to prevent the coins from getting to the drain filer 1st and the back up was the screws in the drain filter.
  • Kerry from Alleyton, tX, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Socket set
  • Parts Used:
    W10536347
59 of 71 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Original drain pump housing broke causing leak all over laundry room floor
What a mess!
Unplug the unit, disconnect the hot and cold water supply lines. Remove the drain hose from the wall and slide the unit away from the wall.
It's easier if you lay the unit on it's side, but not required.
Using the flat blade screwdriver, or a 1/4" nut driver, remove the 8 bolts that hold the back cover and lay that aside.
Locate the leaky pump. There are 2. One is the supply pump. One is the waste drain pump and they are not interchangeable.
Using the pliers, slide the spring clamps off of the 2 hoses connected to the pump.
Using a phillips-head screw driver, remove the 3 screws holding the pump to the unit.
Hinge open the cover to the electrical supply for the pump and pull out the connector. It only goes on one way, so reassembly is not an issue.
Throw pump across the street.
Take new pump and reverse instructions above.
  • tom from Vienna, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
  • Parts Used:
    W10536347
41 of 44 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
cracked water pump from change
first flipped washeron its front, took water pump off, put new water pump on and flipped it back upright.
then took basket out of washer to get remaining change out of washer. fairly simple the third time it has to be done,
I also put two short screws into the suction screen of the pump so that no change can reach the pump anymore
  • Kevin from Mount Gilead, OH
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
  • Parts Used:
    W10536347
27 of 30 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water drain pump leaks
This is the second time that I had to replace this pump. The plastic pumps do not handle pocket change very well.Unplug machine,disconnect water lines and discharge flex hose.Tip machine over to front side to gain access to pump.Remove back panel of washer(8 screws). Remove the three screws and hose clamps.Unplug power to pump. Look for coins in pump and in bottom of washer tub.Remove coins if you can.Install new pump and replace back panel.Tip machine back up right.To make sure that I had removed all coins I had to remove stainless steel tub.Use putty knife to release clips that hold the top of washer.These are about 6" in from both sides of front .Push in and lift top away and back.Remove plastic around out side of basket.It just snaps off. Pry off center cap in bottom of basket. Remove nut with socket wrench.It might be pretty snug.Lift out basket. This might be snug also but it will come out.Now you have access to whatever may be entering your pump. I found a quarter and a penny . Remove plastic cover at bottom of tub (2 screws). This is where I found the penny.Good time to clean washer is now. Mine was really scuzzy.Put everything back together and you are good to go.Make sure to check pockets for that loose change,so you don't have to do this a second time.
  • Kevin from Scribner, NE
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set
  • Parts Used:
    W10536347
27 of 33 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
would not pump out water
remove back cover plate to access pump replacement of the pump is rather simple the time consumption was because when I examined the pump I found a nickel which wiped out the impeller on the pump after further examination I found other small change in the suction side of the pump unit As a result of this I had to remove the barrel to further clean the reservoir to avoid damaging the new pump.I have repsaired this washer no less than six times over the years.This is a very poorly designed unit for the cost Thank you for the rapid delivery of the part.This wont be the last time I deal your on line service was excellent.Luckily my mechanical experience saved me a ton of money.
  • Phil from Bordentown, NJ
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers, Socket set
  • Parts Used:
    W10536347
26 of 30 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
coin in drain pump put a hole in casing
unscrew all the screws on the back of your cabrio washer just the bottom portion to access the drain pump which is located on bottom left underside of the wash drum, the drum on mine is plastic or plastic shroud i guess , theres 3 screws that hold the pump into place, also 2 hose clamps, and the power source, the cap that covers the power source is a bit of a pain to unsnap do this part last cause you'll be able to pull it out from under the drum and get to it easier. once the pump is free just do everything in reverse and you'll be good to go in about 30 to 40 mins . one more thing dont try to caulk or seal on the one thats broke its a lost cause just replace it and make sure like i have been lol no coins left in your pockets before they get washed......whirlpool cabrio other number i got off sticker besides model number is type 580 hope this is helpfull
  • jon from hannibal, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Socket set
  • Parts Used:
    W10536347
14 of 18 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drain Pump Leaking
Was pretty strait forward. Took the back panel off, removed the 3 mount screws and 2 clamps on the pump, and swapped it all out. Only thing, Paid for 2 day air shipping, took a week for the part to come in. But it was still faster and cheaper then my local parts dealer.
  • Shaun from Central Valley, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
  • Parts Used:
    W10536347
10 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
leaking water pump
The most difficult problem was to identify where the leak was and I tried to repair the old pump but that was a waste of my time. I was most impressed with this company in how fast the order was taken and the perfect part was shipped to me. I received the part in approx. 30 hours after I placed the order. The part was delivered by FedExpress to my front door. A very reasonable price for the part. Anyway, most anyone could have done the repair that I did without difficulty.
  • Houston from Ocoee, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
  • Parts Used:
    W10536347
10 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Slow leak from a cracked drain pump
I wasn't able to turn the washer on it's side or front, and instead had to prop it slightly up on cinder blocks due to the configuration of my laundry room. The actual repair was fairly simple, had the clamps supplied been easy to manuever, but they were not. The clamp that goes around the hose from the pump into the inlet valve wouldn't go down around the valve where it was supposed to. I had it too far up, so when I ran the washer, the whole hose popped out and flooded my laundry room. My husband suggested a better clamp, the type that actually opens and you can tighten with a screw system. $2.16 at Lowes. 2nd attempt at repair was successful, and so far no leaks. So...save yourself some time and when you get the replacement pump, take those clamps over to Lowes or Home Depot and buy a clamp that you can open fully, slip over the valve, and tighten as much as you need. If I had that type of clamp to begin with, this project would have taken an hour, tops. And by the way, I'm a 36 year old woman with NO experience fixing appliances, but plenty of experience paying other people too much money to fix things that never should have broken in the first place!
  • Sarah from Olympia, WA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Pliers, Screw drivers, Wrench (Adjustable)
  • Parts Used:
    W10536347
9 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer Reviews
Average Rating:
★★★★★
★★★★★
22 Reviews
4.7
Filter By Rating:
  • 5 Stars
    17
  • 4 Stars
    4
  • 3 Stars
    1
  • 2 Stars
    0
  • 1 Star
    0
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
Model Cross Reference
This part works with the following models:
PartSelect Number: PS5136124
Manufacturer Part Number: W10536347
Brand
Model Number
Description
Kenmore
11027032600
Washer
Kenmore
11027032601
Washer
Kenmore
11027032602
Washer
Kenmore
11027032603
Washer
Kenmore
11027042600
Washer
Kenmore
11027042601
Washer
Kenmore
11027042602
Washer
Kenmore
11027042603
Washer
Kenmore
11027052600
Washer
Kenmore
11027052601
Washer
Kenmore
11027052602
Washer
Kenmore
11027062600
Washer
Kenmore
11027062601
Washer
Kenmore
11027062602
Washer
Kenmore
11027062603
Washer
Kenmore
11027062604
Washer
Kenmore
11027072600
Washer
Kenmore
11027072601
Washer
Kenmore
11027072602
Washer
Kenmore
11027072603
Washer
Kenmore
11027072604
Washer
Kenmore
11027082600
Washer
Kenmore
11027082601
Washer
Kenmore
11027082602
Washer
Kenmore
11027082603
Washer
Kenmore
11027082604
Washer
Kenmore
11027082605
Washer
Kenmore
11027086600
Washer - RESIDENTIAL WASHER
Kenmore
11027086601
Washer
Kenmore
11027086602
Washer

Get in touch, we're here to help!

Open until 1am EST

Contact Customer Service