Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Ralph
February 10, 2022
I need actuator with "rev 011" stamped on it. Does this actuator have that revision on it
For model number wtw4800bq1
Hello Ralph, thank you for writing. We can confirm that this Actuator has "rev 011" stamped on it. Our part number is PartSelect Number PS16221077. Good luck with your repair.
3 people found this helpful.
Was this helpful?
Thank you for voting!
Sean
September 27, 2022
Washer agitated and drains, but won't spin at the end of the cycle.
For model number maytag washer mvwc565fwo
Hello Sean, thank you for your inquiry! Our research indicates that the issue is probably with the Drive Belt, part number PS11747978. If that is not the problem or if you have already fixed that, then the problem would be related to the Drive Hub Kit, part number PS6012095. Customer service is available 7 days a week if you need help placing an order. Glad to be of assistance!
Washer sticks on sensing mode, just keeps filling with water
For model number WTW5000DW1
Hello Ralph, Thank you for the question. When the Washer is stuck on Sensing Cycle and not proceed to the Wash cycle, it is most likely a defective Water Filter. We hope this helps!
My whirlpool washing machine stays in sensing mode and makes a buzzing noise sound. Is it the shift actuator that's messed up?
For model number WTW5000DW1
Hello Montona, Thank you for the question. Your washer senses the contents to determine the load size and balance to decide on the right amount of water to clean the load. If it is stuck in sensing mode, you can try to reset the appliance. To reset, unplug the washer and leave it for about 15 to 20 minutes before powering it on again. Lift and close the lid about six times within 12 seconds to reset the unit. We hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Glenn
December 12, 2022
actuator stim pops out hole pup backi works fine week or two
For model number mvwc565fw2
Hello Glenn, thank you for contacting us. If the issue is recurring, the most likely solution is to replace the shift actuator, part number PS11769864. Also, make sure it is mounted correctly. Please watch the attached video for proper installation instructions. Customer service is available 7 days a week if you need help placing an order. Glad to be of assistance!
I noticed this repairs agitator not spinning. My agitator spins but the tub does not spin on the spin cycle, but the agitator spins fast, then stops when the tub doesn’t spin. I’m thinking this switch is not working to engage the tub gear on the pulley. Does that sound accurate? Thank you!!!
For model number 11025132411
Hello Rob, thank you for contacting us. Yes, the most probable cause of the issue is a failed actuator, part number FIX16221077. It moves an inner gear inside the gear case to initiate the wash or spin cycle. Customer service is available 7 days a week if you require assistance placing an order. Thanks again for reaching out!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Jared
14 days ago
My washer fills with water and agitates but wont switch to the rinse cycle. It says it doesn’t detect water, but it just got plenty of water to go through the wash cycle. And I recently changed the water inlet.
For model number MVW6230hc2
Hi Jared, thank you for contacting us. First, we recommend checking if the inlet valve is installed correctly. If this does not help, we recommend checking the wire harness, part number PS16730931. If the issue persists, then you may need to change the control board, part number PS16660484. We hope this sorts out your problem!
I have changed out the pump, belt, and actuator on my washer it still will not spin out the clothes. The grinding noise is still sounding as well. What more can I do?
For model number MVWC415EW1
Hello Dorothy, thank you for contacting us. We recommend inspecting the following parts that could be the culprit and be making noise: the drive pulley, part number PS10057144, the gear case, part number PS16220910, the motor, part number PS11726282, the suspension rod, part number PS11703287. Customer service is always available to help you place an order if you are having trouble doing so. Good luck with your repair.
Does this part make iit spin and drain? Our washer will not spin.
For model number MVWX655DW1
Hello Todd, thank you for getting in touch. The washer belt is what is used to spin the drum. We recommend you check the following parts: drive belt, part number PS11747978, gearcase, part number PS16220911, drive motor, part number PS12584593, and drive hub kit, part number PS6012095. Please reach out to customer service if you need help placing an order, anyone will be happy to assist you. We hope that helps.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Machine would stop at spin cycle
After disconnecting water lines and power, tip machine onto its back. The actuator is located under the drum. Remove the cover over the motor/ drive belt. Actuator is located by the transmission and held on by several screws. Unplug the wiring harness and remove three screws with Phillips screwdriver. Install new actuator..
Steven from COHOES, NY
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
4 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer was stuck on rinse cycle
Research showed it was the transmission and the actuator . Parts were super easy to install and it solved the issue 100%
PS - I put some light lithium grease on the transmission and it’s quieter than it was when new
When to PartSelect Web site, used their trouble shooting guide, Used their advice, which was to replace the actuator. bought and installed the actuator which took around 20 minutes or so. washer started working fine after replacing. Thanks to the website I save a lot of money. Thanks PartSelect
The Fix App makes it easy to manage all your stuff in one place. Just snap a photo and we'll find and store your user manuals, receipts, and product information in one easy-to-find place!
"Like magic. I took a picture of the model number on my refrigerator, and the app identified it right away … Very convenient. I'm impressed." ★★★★★ - Clever Jeff
Stay on this site
Go to Canadian site
In Stock
