This is a replacement clutch assembly or cam kit for your washer. The clutch assembly is mounted on the drive shaft on the bottom of your washer. You may need to replace the clutch assembly if the spl...
$54.38
In Stock
Order within the next 6 hrs and your part ships today!
This drive hub kit (part number W10528947VP) is for washers.
Drive hub kit W10528947VP connects the spin basket to the spin shaft that spins the basket. The kit may include multiple parts; refer to...
$33.94
In Stock
Order within the next 6 hrs and your part ships today!
This water inlet valve is for washers.
The water inlet valve controls the water flow into the washer.
Unplug the washer and shut off the water supply before installing this part. Wear work glove...
$70.56
In Stock
Order within the next 6 hrs and your part ships today!
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installat...
$11.10
In Stock
Order within the next 6 hrs and your part ships today!
Order within the next 6 hrs and your part ships today!
Questions And Answers for 11022352510
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
5 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jerry
December 30, 2019
Lid lock broken. Machine will not spin and drain?
For model number 11022352510
Hello Jerry,
Thank you for your question. The lid lock assembly for your model is under part PS12704713. We hope this helps!
Washer makes clicking sound when washing. It also doesn't completely drain water all the time. What may be causing this problem.
For model number 11022352510
Hello Lawrence, thank you for getting in touch. According to our research, we would recommend checking the door lock first. If it is fine, then the issue is most probably with the electronic control board, part number PS12114299. It manages the washer's functions such as filling, washing, draining and spinning. You may need to replace it to fix the issue. We hope this information helps!
Always has balance issues no matter what size of load . Is the sensor the problem
For model number 11022352510
Hi Patty, thank you for contacting us. Based on our understanding of the issue, we would suggest that you make sure the washer is level. If that is not causing the issue, then you may need to check the suspension rods, part number PS12347546, as they are most likely faulty and may need to be replaced. We hope this helps!
Hi Sandy, thank you for writing in. Here are the steps to remove the agitator from your washer...To replace your washers agitator first
0:09
remove the fabric softener dispenser and
0:11
lint cap if applicable to your model
0:16
then use a 7/16 inch socket with a 12
0:19
inch extension to loosen the mounting
0:22
bolt with the bolt loosened pull the old
0:26
agitator up and out
0:32
install the new agitator by first
0:35
inserting the mounting bolt now slide
0:41
the new agitator onto the drive shaft
0:45
and tighten the bolt to secure replace
0:53
the lint cap if necessary and the fabric
0:58
softener dispenser with the new agitator
1:02
installed make sure all tub components
1:04
are functioning properly during the wash
1:06
cycle
We hopw this helps.
Well, first investigated and found loose nut on drive clutch. First take off the two screws with nut drive then cover off using a screwdriver blade to snap off the cover. Then socket ratchet to take off the nut on drive clutch. take off belt by slowly rotating the drive gear. two screws that hold the electronics to the upper drive clutch
... Read moreand put aside, so you can snap off the cover for drive clutch on upper part with screwdriver and off the parts come and install whole unit back as took it apart. Line up the new upper clutch so that is position as was before. (Using parts diagram helps a lot as www. partsselect.com has for you or Maytag.com.) Then put the electronic part board back on and the gear and nut. Make sure it is tight by several attempts to make sure it's snugged up good and then slowly roll belt back on the pulley and motor drive. Put your cover guard back on with two screws and done.
ordered hub and it shipped quickly. I was able to put the hub in place and screw the screws in. you want to tighten them down slowly and go around to each screw tightening a little at a time so you don't break the hub. as you tighten the screws down the hub slides down flush. its impossible to just push the hub on with your hand. Buttoned
... Read more it back up and got caught up on laundry. good day when the washer is fixed.
