KitchenAid Dishwasher Pumps
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular KitchenAid Dishwasher Pumps
Your Price
$62.60
In Stock
KitchenAid Dishwasher Drain Pump
First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done. Read more...
PartSelect Number PS11753379
Manufacturer Part Number WPW10348269
This drain pump is used in dishwashers to remove water from the dishwasher tub. If the impeller in the dishwasher is damaged or the motor has been shorted out and will not drain, it is possible the body is cracked, causing leakage. To prevent this from happening, replace the drain pump. The tools needed for this installation are: Phillips screwdriver, 5/16 inch nut driver, 5/8 inch wrench, and a flathead screwdriver. Remember to unplug your dishwasher from the power source before beginning this installation project. Refer to the manual provided by the manufacturer for further installation instructions.
Fixes these symptoms
- Leaking
- Noisy
- Not cleaning dishes properly
- See more...
Installation Instructions
Andrew from Alexandria, VA
dishwasher not draining after wash cycle
Caviat: The actual repair is less than 15 minutes, but I spent a lot of time playing with it before I figured out it was that easy and fast. You don't need to remove the dishwasher from the counter to do this. And it will probably help to look at the new part closely so you can understand where the retainer clip is to press it and release the old pump.First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done. Read more...
Your Price
$74.08
In Stock
KitchenAid Dishwasher Circulation Pump
PartSelect Number PS16744935
Manufacturer Part Number W11612327
The pump motor delivers water to the spray arms to clean the dishes during the wash cycle.
Fixes these symptoms
- Not cleaning dishes properly
- Not draining
- Will not fill with water
- See more...
Your Price
$65.73
In Stock
KitchenAid Dishwasher Drain Pump
Used pliers to loosen the pressure clamp on drain pump , have towel handy as there will be some water. Turn pump to left as you push in on the clip on side of drain pump. It will come out. Remove wire plug from old pump and plug into new pump than insert new pump and turn and push in till it clicks. Use pliers to pinch hose clamp and push hose onto pump release hose clamp. Turn breaker on. Run a cycle and make sure all is tight before putting skirt on front. Read more...
PartSelect Number PS11738151
Manufacturer Part Number W10876537
If your dishwasher isn’t draining properly or leaving water behind, this drain pump motor assembly might be the fix you need. It helps clear water from the tub during the drain cycle, keeping your appliance running smoothly and your dishes clean. This genuine replacement part is made to fit a variety of models from Whirlpool and related brands like Kenmore, KitchenAid, and Amana, making installation straightforward and dependable.
Fixes these symptoms
- Leaking
- Not draining
- See more...
Installation Instructions
Kelli from BURLINGTON, MA
Dish washer would not drain properly
Shut off breaker. Took off front skirt of dishwasher . Used pliers to loosen the pressure clamp on drain pump , have towel handy as there will be some water. Turn pump to left as you push in on the clip on side of drain pump. It will come out. Remove wire plug from old pump and plug into new pump than insert new pump and turn and push in till it clicks. Use pliers to pinch hose clamp and push hose onto pump release hose clamp. Turn breaker on. Run a cycle and make sure all is tight before putting skirt on front. Read more...
Your Price
$34.74
In Stock
KitchenAid Dishwasher Chopper Assembly
2) Remove lower spray arm by unscrewing plastic screw, it should only be hand tight.
3) In order to remove the strainer cover, you will need to remove the plastic tube that takes water to the middle and top spray arms. Unclip this tube from the top and middle clips and then work it out of the strainer assembly tube. Now you should be able to remove the tube at the bottom of the dishwasher by unscrewing it 1/4 turn.
4) Remove the strainer cover by unscrewing the 4 Torqs screws.
5) You will now see two smaller torqs screws that hold the hold the Chopper Assembly cover down. Take these two screws out and remove the two piece cover.
6) Pull out the broken Chopper Assembly, make sure you get all the pieces!
7) Install the new Chopper Assembly. Make sure that you install the Assembly with the small part of the screen towards the bottom of the housing. Also make sure you compress the spring as you install the part. I used a small pair of neddle nose pliers to compress the spring behind the screen in order to install the chopper assembly.
8) Put everything back together and make sure it works! Read more...
PartSelect Number PS1734917
Manufacturer Part Number W10083957
This is a chopper assembly or drain food chopper, and it is designed for your dishwasher. The chopper chops up/minces the food particles in your dishwasher to prevent them from clogging the pump. You may need to replace this part if your dishes are not being cleaned properly, your appliance is particularly noisy, or you are noticing draining problems. The tools you will need to make this repair include a number 20 and a number 15 torque screwdriver, a small flat blade screwdriver, and a pair of needle nose pliers.
Fixes these symptoms
- Leaking
- Noisy
- Not cleaning dishes properly
- See more...
Installation Instructions
Bill from North Richland Hills, TX
Dishes on top rack of dishwasher were not being cleaned.
1) Remove top and bottom dish baskets from the dishwasher, this will give you room to work. To remove top basket there are clips at the end of the slide rails.2) Remove lower spray arm by unscrewing plastic screw, it should only be hand tight.
3) In order to remove the strainer cover, you will need to remove the plastic tube that takes water to the middle and top spray arms. Unclip this tube from the top and middle clips and then work it out of the strainer assembly tube. Now you should be able to remove the tube at the bottom of the dishwasher by unscrewing it 1/4 turn.
4) Remove the strainer cover by unscrewing the 4 Torqs screws.
5) You will now see two smaller torqs screws that hold the hold the Chopper Assembly cover down. Take these two screws out and remove the two piece cover.
6) Pull out the broken Chopper Assembly, make sure you get all the pieces!
7) Install the new Chopper Assembly. Make sure that you install the Assembly with the small part of the screen towards the bottom of the housing. Also make sure you compress the spring as you install the part. I used a small pair of neddle nose pliers to compress the spring behind the screen in order to install the chopper assembly.
8) Put everything back together and make sure it works! Read more...
Your Price
$200.31
In Stock
KitchenAid Dishwasher Circulation Pump And Motor
Never done any repair before on an appliance, but a lot less expensive than repair person who wanted $665 + tax. Read more...
PartSelect Number PS12745416
Manufacturer Part Number W11414076
The circulation pump and motor assembly is essential for delivering water to the spray arms in your dishwasher to ensure clean dishes. This genuine OEM replacement part is compatible with several dishwasher models. Be sure to disconnect the power before installing the part and wear gloves to avoid injury.
Fixes these symptoms
- Noisy
- Not cleaning dishes properly
- Will Not Start
- See more...
Installation Instructions
Dennis from Bradley Beach, NJ
No Water Going to Spray Arms
Disconnected water, drain and electricity. Pulled machine out and put on its back to access bottom. It's a matter of swapping out the part. You do have to "move" some blocking parts, but no big deal. Only issue is you need to have traditional hose clamps as the 2 OEM clamps are 1 time use and if you do not have the crimper, you need to replace with standard ones. Also, no one tells you that you may need to "reset" the machine when you put the power back on. I had an error /fault code of FA E5 which is a drain issue. Just cut the power for a couple of minutes, open the door, hit CANCEL twice ( you may need to hit HEATED DRY too), put power back on, and the fault code will go away. Not sure if this is what the factory says, but a bit of trial and error solved it.Never done any repair before on an appliance, but a lot less expensive than repair person who wanted $665 + tax. Read more...
Your Price
$60.51
In Stock
KitchenAid Dishwasher Drain Pump
PartSelect Number PS11756031
Manufacturer Part Number WPW10531320
This drain pump is an authentic OEM replacement part for models of dishwasher. It is responsible for removing wastewater from the dishwasher during the drainage cycle. It is located at the bottom of the dishwasher and can be accessed by removing the lower access panel or by tipping the dishwasher on to its rear side. When activated, the drain pump pushes the wastewater through the drain hose and into the household plumbing system or garbage disposal. If the drain pump malfunctions or becomes clogged, it can lead to drainage issues, resulting in water pooling at the bottom of the dishwasher, foul odors and potentially resulting in incomplete cleaning of dishes.
Fixes these symptoms
- Leaking
- Noisy
- Not draining
- See more...
Installation Instructions
Douglas from SAINT JOHN, IN
Dishwasher was making a moaning sound when draining.
Unplug dishwasher. Remove lower front accessible panel. Disconnect wires to the drain pump. Rotate pump to unlock and remove. Apply plumbers grease to rubber seal and install new pump. Connect wires. Plug in dishwasher and run rinse cycle to check for no water leak. If all okay replace access panel. Done.
Read more...
Your Price
$157.45
In Stock
KitchenAid Dishwasher Pump And Motor Assembly
PartSelect Number PS16875975
Manufacturer Part Number W11665769
This dishwasher pump and motor assembly is compatible with dishwashers. It is supplied directly by the original manufacturer to ensure that it fits perfectly with your model. The pump and motor are responsible for moving water throughout the dishwasher during the wash cycle. The pump draws water from the tub and pumps it through various channels, such as the detergent dispenser, spray arms, and drain hose. The motor provides the power necessary to drive the circulation pump, causing the pump to rotate and circulate water. If the assembly is faulty, you will notice difficulties starting or filling the dishwasher, poor cleaning performance, incomplete cycles, and water leaks.
Fixes these symptoms
- Leaking
- Not cleaning dishes properly
- See more...
Your Price
$85.55
In Stock
KitchenAid Dishwasher Drain Pump
PartSelect Number PS12741766
Manufacturer Part Number W11412291
Introducing the Whirlpool Drain Pump: a key component to optimize the functionality of your dishwasher. This authentic OEM part specially developed for Whirlpool is compatible with various models of Whirlpool dishwashers. Gone are the days of standing water as this dependable pump expertly removes water during the crucial drain phase of your dishwashing cycle. Before installation, remember to disconnect your dishwasher and turn off the water supply for safety reasons; gloves are encouraged to safeguard your hands during the process. Distinguished for its superb reliability, this is a Drain Pump that will notably elevate your dishwashing routine. Please always confirm that this part aligns with the specifications of your model to ensure optimum performance.
Fixes these symptoms
- Not draining
- See more...
Installation Instructions
Bruce from MADISON, MS
I was getting the F9 E1 error code intermittently then consistently.
Checked drain hose and it was clear without kinks. I shut of the electrical breaker. Verified no power to washer. Removed the lower trim panel. Lowered the adjustable feet to allow me to slide my unit out. Disconnected drain hose from unit. Pulled unit from cabinet. My drain pump is located on the right bottom side when facing the door of the unit. I did not need to lay the unit on its side and have enough power cable to not have to disconnect it while still pulling the unit all the way out of the cabinet. The pump is easily accessed from the right side hidden behind insulation. Disconnected power wire from pump. Pressed down locking latch and turned pump counter clockwise removed then replaced in opposite order. I have run 3 load’s before posting this and as of now my dishwasher is functioning perfectly.
Read more...
Your Price
$105.35
In Stock
KitchenAid Dishwasher Drain And Wash Impeller Kit
PartSelect Number PS382822
Manufacturer Part Number 675806
This dishwasher drain and wash impeller kit comes with both the drain and wash impeller, gaskets, chopper, and installation screw. This part helps stop your dishwasher from leaking and helps with the proper draining of the dishwasher. If you notice that your dishes are not cleaning, the dishwasher is not draining properly, or is making any unusually loud sounds or grinding noises, this could indicate the impeller and seal kit have broken down and need to be replaced. You will need a #15 and #20 torx driver, a small flat-blade screwdriver, 1/4-inch nut driver, adjustable wrench, and a small hammer and a sharp chisel.
Fixes these symptoms
- Leaking
- Noisy
- Not cleaning dishes properly
- See more...
Installation Instructions
Daniel from Sarasota, FL
leaking from tub above motor
Disconnect unit and remove from under counter. remove lower spray arm, tip over dishwasher on it's back, diconnect wires from motor , unscrew drain fitting rotate motor mounts to and lift pump and motor assembly up and out from inside the dishwasher. thoughly clean all parts during pump disassembly( under running water and a toothbrush works well) . Looking at a parts diagram,and using your memory from disassembly replace the new seals and put it all back together, with patience you can do anything and use common sense.
Read more...
Your Price
$191.91
In Stock
KitchenAid Dishwasher Pump And Motor Assembly
PartSelect Number PS11756692
Manufacturer Part Number WPW10605057
This pump and motor assembly circulates water in dishwashers during the wash cycle. Check the motor’s resistance if water isn't circulating, and replace if needed. Verify compatibility with your model.
Fixes these symptoms
- Leaking
- Not cleaning dishes properly
- See more...
Installation Instructions
J.D, from COCOA, FL
Washer pump wasn't working
I found a video on youtube that was very detailed explaining how to change out the same unit I purchased (Pump and Motor Assembly Model # KDFE104DBL0). If you have basic mechanical skills and the proper tools this video will make installation much easier. https://www.youtube.com/watch?v=Johlq5qbmEI
Read more...
Related KitchenAid Dishwasher Parts
- All KitchenAid Dishwasher parts
- KitchenAid Dishwasher Brackets and Flanges
- KitchenAid Dishwasher Caps and Lids
- KitchenAid Dishwasher Circuit Boards and Touch Pads
- KitchenAid Dishwasher Dishracks
- KitchenAid Dishwasher Dispensers
- KitchenAid Dishwasher Doors
- KitchenAid Dishwasher Ducts and Vents
- KitchenAid Dishwasher Filters
- KitchenAid Dishwasher Fuses
- KitchenAid Dishwasher Handles
- KitchenAid Dishwasher Hardware
- KitchenAid Dishwasher Hoses and Tubes
- KitchenAid Dishwasher Insulations
- KitchenAid Dishwasher Latches
- KitchenAid Dishwasher Lights and Bulbs
- KitchenAid Dishwasher Manuals and Literatures
- KitchenAid Dishwasher Motors
- KitchenAid Dishwasher Panels
- KitchenAid Dishwasher Seals and Gaskets
- KitchenAid Dishwasher Spray Arms
- KitchenAid Dishwasher Springs and Shock Absorbers
- KitchenAid Dishwasher Switches
- KitchenAid Dishwasher Valves
- KitchenAid Dishwasher Wheels and Rollers
- KitchenAid Dishwasher Wire Plugs and Connectors